User Guide

ManualsBrandsJohnson Controls ManualsFan Coil ThermostatsNon-programmable FCU and PTAC Thermostat, On/Off 3-Speed Fan Control w/o Johnson Control Logo

FCP-NA-701, FCP-PA-701

FCP Non-programmable and Progammable Fan Coil or PTAC

Thermostat

24-11482-00006 Rev. —

August 2020

Quick Start Guide

*241148200006-*

Parts included

• One FCP thermostat

• One Quick Start Guide

• Four mounting screws

• One lock screw

• Seven pre-installed terminal wires

• One wire label

• One coin cell battery (included only with FCP-PA-701)

Applications

The FCP-NA-701 non-programmable, non-connected fan coil unit (FCU) or package terminal air conditioning (PTAC) thermostat and

FCP-PA-701 programmable, non-connected FCU or PTAC thermostat are compatible with most 24 VAC FCU or PTAC equipment.

The following list shows the compatible congurations of the equipment:

• 2-Pipe with 3-speed fan

• 4-Pipe with 3-speed fan

• Conventional PTAC

• Heat pump PTAC with or without auxiliary heat

North American emissions compliance

United States

Canada

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment o󰀨 and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit di󰀨erent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

CAN ICES-3(B)/NMB-3(B). This Class (B) digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la Classe (B) respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Number Description

1 Schedule

2 Time

3 Room temperature

4 Temperature setpoint

5 Fan speed

6 Mode

7 Down

8 Up

9 Fan

10 Cool or heat status

11 Day

Figure 1: FCP dimensions, in. (mm) and UI layout Table 1: UI layout

Summary of content (10 pages)

PAGE 1
*241148200006-* FCP-NA-701, FCP-PA-701 FCP Non-programmable and Progammable Fan Coil or PTAC Thermostat 24-11482-00006 Rev. — August 2020 Quick Start Guide Figure 1: FCP dimensions, in.
PAGE 2
FCP-NA-701, FCP-PA-701 Risk of Electric Shock Disconnect the power supply before making electrical connections. Contact with components carrying hazardous voltage can cause electric shock and may result in severe personal injury or death. Risque de décharge électrique Débrancher l’alimentation avant de réaliser tout branchement électrique. Tout contact avec des composants conducteurs de tensions dangereuses risque d’entraîner une décharge électrique et de provoquer des blessures graves, voire mortelles.
PAGE 3
FCP-NA-701, FCP-PA-701 Figure 4: Attaching the trim plate to the junction box Figure 5: Attaching the back housing to the trim plate Figure 6: Attaching the front housing to the back housing Wiring Figure 7: 2-Pipe fan coil unit Figure 8: 4-Pipe fan coil unit 3 24-11482-00006 Rev.
PAGE 4
FCP-NA-701, FCP-PA-701 Figure 9: Conventional PTAC Figure 10: Heat pump PTAC Setup and adjustments Preset configuration profiles The FCP thermostat includes 20 preset configuration profiles. You can use these profiles to quickly configure essential settings, such as system type, remote sensor, and pipe sensor. The thermostat screen shows the preset configuration menu on the first power up or after a factory reset.
PAGE 5
FCP-NA-701, FCP-PA-701 Table 2: Preset configuration profiles Profile # Remote sensor Pipe System sensor type 2-pipe FCU with aux heat Available modes: 1: heat only 2: cool only 3: heat and cool with Auto 4: heat and cool without Auto HP valve type Remote sensor location: 0: in room 1: in duct Pipe state calendar Pipe state: 0: heat 1: cool Number of fan speeds 1 Yes Yes 2-pipe FCU Yes 3 - 0 Off - 3 2 Yes Yes 2-pipe FCU Yes 3 - 1 Off - 3 3 Yes Yes 2-pipe FCU No 4 - 0
PAGE 6
FCP-NA-701, FCP-PA-701 Control mode The FCP thermostat supports the following control modes: Table 4: FCP available modes System type Control mode 2-pipe FCU with aux heat Heat only Cool only Heat and cool without auto Heat and cool with auto 2-pipe FCU No    - 2-pipe FCU Yes  -   4-pipe FCU     PTAC conventional     PTAC heat pump     Press Mode to access the control mode menu. Press Mode again to select the required control mode.
PAGE 7
FCP-NA-701, FCP-PA-701 Table 5: User preference settings Menu item Description Setting options Default 01 Temperature scale F: Fahrenheit C: Celsius F 02 User temperature calibration Temperature with calibration value. Offset: +/- 5.4°F (+/3.0°C) 0.0°F (0.0°C) 03 Temperature calibration – remote sensor Temperature with calibration value. Offset: +/- 5.4°F (+/3.0°C) 0.0°F (0.0°C) 04 Temperature calibration – pipe sensor Temperature with calibration value. Offset: +/- 5.4°F (+/3.0°C) 0.
PAGE 8
FCP-NA-701, FCP-PA-701 Table 6: System configuration settings (part 2 of 2) Menu item Description Setting options Default 28 Pipe state – calendar ON OFF OFF 29 Heat to cool day (unavailable if pipe state – calendar = OFF) 1-Mar to 31-May 15-Apr 30 Cool to heat day (unavailable if pipe state – calendar = OFF) 1-Sep to 30-Nov 15-Oct 31 Pipe state (unavailable if system type ≠ 2FCU or if pipe sensor = true or if pipe state – calendar = ON) 0: heat 1: cool 0 32 Heat to cool threshold (una
PAGE 9
FCP-NA-701, FCP-PA-701 To calibrate the remote sensor, complete the following steps: 1. Press Mode to set the thermostat to OFF mode. 2. Press and hold Mode and Fan for 5 seconds to access the advanced settings menu. 3. Press Up to navigate to User Preference Settings, then press Mode to enter the menu. 4. Press Mode to navigate to 03. 5. Use the Up and Down buttons to change the option, then press Mode to confirm the change. 6.
PAGE 10
FCP-NA-701, FCP-PA-701 Table 7: Common errors (part 2 of 2) Error code Description Solution ER:12 Pipe sensor detected a too low temperature. • Verify if the pipe sensor is installed correctly in the pipe. • Contact technical support. ERROR_PIPE_ SENSOR_LO Technical specifications Table 8: FCP technical specifications Specification Description Models Non-programmable: FCP-NA-701-N, FCP-NA-701-B Programmable: FCP-PA-701-N, FCP-PA-701-B 20 VAC to 30 VAC, 60 Hz, max.