Quick Start Guide

Wireless ratings
Standard IEEE 802.11
Band b/g/n
Frequency range 2412 MHz to 2462 MHz
Antenna 2 dBi Dipole
Transmission power 18.98 dBm EIRP
Component Specification
Differential pressure sensor specifications
Air flow sensor 0 Pa to 500 Pa per 0 in. to 2 in. of water
Controller processor and memory specifications
Main processor Qualcomm 560Mhz
Processor ARM Cortex 48 Mhz
Flash memory 32 MB
RAM 128 MB
Product temperature and humidity specifications
Dimension 230 mm or 9.1 in. x 104 mm or 4.1 in. x 44
cm or 1.7 in.
Material UL Approved
Weight 500 g
Physical specifications
Dimension 230 mm or 9.1 in. x 104 mm or 4.1 in. x 44
cm or 1.7 in.
Material UL Approved
Weight 500 g
Physical specifications
Dimension 230 mm or 9.1 in. x 104 mm or 4.1 in. x 44
cm or 1.7 in.
Material UL Approved
Weight 500 g
Building Technologies & Solutions
Headquarters: Milwaukee, Wisconsin, USA
Branch offices: Principal cities worldwide
Johnson Controls
®
is registered trademark of Johnson Controls.
All other marks herein are the marks of their respective owners.
© Copyright 2022 Johnson Controls. All rights reserved. Any unauthorized use or copying is strictly prohibited.
UL input, output, and communication ratings
Description Specification Terminal
Power supply Nominal 24 VAC H and G
Minimum 20 VAC
Maximum 30 VAC
50 Hz or 60 Hz
Power supply Class 2
Universal
inputs
Voltage 0 VDC to 10 VDC,
Class 2
UI1 and
COM to
UI4 and
COM
Resistance 400 ohm to
200,000 ohm
Digital outputs
(SPST N.O. dry
contact)
24 VAC, 0.5 A pilot duty, Class 2 DO1, DO2,
DO3
Analog output Voltage 0 VDC to 10 VDC AO1and
COM to
AO4 and
COM
Digital outputs
(SPST N.O.
dry
contact)
24 VAC, 0.5 A pilot duty, Class 2 sadfaf
asdf asd asdf f
DO1, DO2,
DO3
Analog
outputs
Voltage 0 VDC to 10 VDC AO1and
COM to
AO4 and
COM
EIA/RS-485 Class 2 SA Bus +,-
Ethernet Class 2 ETH 1,
ETH 2
Single point of contact
APAC Europe NA/SA
JOHNSON CONTROLS
C/O CONTROLS PRODUCT
MANAGEMENT
NO. 32 CHANGJIANG RD NEW
DISTRICT
WUXI JIANGSU PROVINCE 214028
CHINA
JOHNSON CONTROLS
VOLTAWEG 20
6101 XK ECHT
THE NETHERLANDS
JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA
Technical specifications
North America: UL 60730 Energy Management Equipment; FCC Class B , Part 15 , Subpart C
15.247
CE Compliant
Taiwan
取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大
功率或變更原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信；
經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前述合法通信指依電信
管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻
射性電機設備之干擾。
RED directive
The Equipment named above is confirmed to comply with the requirements set out in the European
Council Directive on the Approximation of the Laws of the Member States relating to 2014/53/EU
(RED).
The equipment passed the following test which was performed according to the following
European standards:
EN 300 328 V2.1.1, EN 301 489-1 V2.2.0, EN 301 489-17 V3.2.0, EN 62311: 2008
UKCA
Directive Electromagnetic Compatibility Regulations 2016:
BS EN 55032:2015+A11:2020, BS EN IEC 61000-3-2:2019, BS EN 61000-3-:2013+A1:2019,
BS EN 55035:2017+A11:2020
FCC
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). This device complies with part 15 of the FCC Rules.
Operation is subject to the follow-ing two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential instal-lation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interfer-ence will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Limited by local law regulations, version for North America does not have region selection option.
This radio transmitter IC: 279A-FWVAV has been approved by Innovation, Science and Economic
Development Canada to operate with the antenna types listed below, with the maximum permissible gain
indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated
for any type listed are strictly prohibited for use with this device.
Gain of antenna: 2 dBi max
Type of antenna: 50 Ohm Dipole
Le présent émetteur radio IC: 279A-FWVAV a été approuvé par Innovation, Sciences et Développement
économique Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain
maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de
l'émetteur.
Gain d'antenne: 2 dBi maximal
Type d'antenne: 50 Ohm Dipole
To satisfy FCC
&IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the
antenna of this device and persons during device operation.
To ensure compliance, operations at closer than this distance is not recommended
Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une
distance de moin de 20 cm. Installer les antennes de facon à ce que le personnel ne puisse approcher à 20
cm ou moins de la position centrale de l’ antenne.
Compliance
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.