Install Instructions

8 M9108, M9116, M9124, and M9132 Series Electric Non-Spring Return Actuators Installation Instructions
Repairs and Replacement
Do not field repair the M9100 Series actuators. To
order a replacement or an accessory, refer to the
Ordering Information section in the M9108, M9116,
M9124, and M9132 Series Electric Non-spring Return
Actuators Product Bulletin (LIT-2681058).
Technical Specifications
Product
M9108, M9116, M9124, and M9132 Series Electric Non-Spring Return Actuators
Power Requirements
M9108-, M9116-AGx: 20 to 30 VAC at 50/60 Hz or 24 VDC ±10%; 6.5 VA supply, Class 2
All Other Models: 20 to 30 VAC at 50/60 Hz or 24 VDC ±10%; 7.5 VA supply, Class 2
Input Signal
AGx: 24 VAC at 50/60 Hz or 24 VDC
GGx, HGx: 0 (2) to 10 VDC, 0 (4) to 20 VDC, or 0 (4) to 20 mA
JGx: Potentiometer value is 100 ohms minimum to
10,000 ohms maximum
Input Signal Adjustments
AGx: Factory Setting: Terminals 1 and 2, CW rotation
Terminals 1 and 3, CCW rotation
GGx, HGx (Voltage Input or Current Input):
Factory Setting: 0 to 10 VDC, 0 to 20 mA, CW rotation with
signal increase
Jumper Selectable: 0 (2) to 10 VDC, 0 (4) to 20 VDC, or
0 (4) to 20 mA
HGx Adjustable Zero: 0 to 6 VDC, 0 to 12 VDC, or 0 to 12 mA
Adjustable Span: 2 to 10 VDC, 4 to 20 VDC, or 4 to 20 mA
GGx, HGx, JGx: Action is jumper selectable Direct (CW) or Reverse (CCW) with
signal increase.
Input Impedance
GGx, HGx: Voltage Input: 205,000 ohms for 0 (2) to 10 V and
410,000 ohms for 0 (4) to 20 V
Current Input: 500 ohms
JGx: Potentiometer Input: 1.8 megohms
Feedback Signal
AGD: 135 ohm feedback potentiometer
AGE: 1,000 ohm feedback potentiometer
GGx, HGx: 0 to 10 VDC or 2 to 10 VDC for 90° (10 VDC at 1 mA)
Corresponds to input signal span selection.
JGx: 0 to 10 VDC for 90° (10 VDC at 1 mA)
Auxiliary Switch Rating
xGC: Two Single-Pole, Double-Throw (SPDT) switches rated at 24 VAC
1.5 A inductive, 3.0 A resistive; 35.0 VA maximum per switch, Class 2
Mechanical Output
(Running Torque)
M9108 Series: 70 lb∙in (8 N∙m) for one unit; not intended for tandem use
M9116 Series: 140 lb∙in (16 N∙m) for one unit
M9116 (in tandem) 280 lb∙in (32 N∙m) for two units (GGx, HGx)
M9124 Series: 210 lb∙in (24 N∙m) for one unit
M9124 (in tandem) 420 lb∙in (48 N∙m) for two units (AGx, GGx, HGx)
M9132 Series: 280 lb∙in (32 N∙m) for one unit,
M9132 (in tandem) 560 lb∙in (64 N∙m) for two units (AGx, GGx)
Audible Noise Rating
45 dBA at 1 m
Rotation Range
0 to 90° in 5-degree increments, mechanically limited to 93°
Rotation Time
M9108: 30 seconds at 50% rated load,
25 to 50 seconds for 0 to 70 lb∙in (0 to 8 N∙m)
M9116: 80 seconds at 50% rated load
70 to 115 seconds for 0 to 140 lb∙in (0 to 16 N∙m)
M9124: 130 seconds at 50% rated load
115 to 175 seconds for 0 to 210 lb∙in (0 to 24 N∙m)
M9132: 140 seconds at 50% rated load
115 to 205 seconds for 0 to 280 lb∙in (0 to 32 N∙m)
Continued on next page. . .