Submittal Sheet

ManualsBrandsJohnson Controls ManualsHVAC Replacement PartsT-5210 Pneumatic Temperature Transmitter w/ 5-1/2" Copper Capillary (50 to 150°F)

Table Of Contents

24- 3910- 0, Rev. G

Part No. 24-3910-0, Rev. G www.johnsoncontrols.com

Code No. LIT-7171170

Product/Technical Bulletin

Issue Date March 2016

T-5210

Pneumatic Temperature Transmitter

Features

• Ball type control port for

increased accuracy

• New lever with reinforced

edges for increased linearity

• New bimetal element to

compensate for ambient

temperature effect

• Integral hypodermic needle

test point

The T-5210 Pneumatic

Temperature Transmitter is

designed to measure a

temperature and convert this

measurement to an air pressure

signal that is transmitted to a

pneumatic receiver, controller, or

receiver-indicator. When used

with a Dewcel



(purchased

locally), the T-5210 can also be

used as a dew point transmitter.

Pneumatic feedback is

incorporated into the transmitter

design to provide an exact

proportional relationship

between the measured

temperature and the transmitted

signal.

Various models are furnished

with appropriate brackets for

mounting to ductwork, walls, or

directly to the hub of a duct

flange or separable well.

Mounting

The T-5210 operates in any

position and should be mounted

on a rigid flat surface. The

instrument requires a .007 in.

restricted supply.

Transmitters with averaging

elements or bulb elements with4

ft (122 cm) capillaries are

furnished with a sheet metal

bracket for surface mounting

using #8 sheet metal screws.

Using the bracket as a template,

mark the two mounting hole

locations and drill a 1/8 in. hole

at each of the marked positions.

Transmitters with bulb elements

and 5-1/2 in. (140 mm)

capillaries are furnished with an

angle bracket for mounting on

the hub of a duct flange or

separable well. The T-5210 is

secured to the flange or well by

tightening the spring locknut

furnished with the well or flange.

Note: When inserting the

bulb into a well other than a

Johnson Controls® well, fill it

one third full of thermal

conductive material

(F-1000-182) and insert the

bulb until it hits the bottom of

the well.

Repair Information

Field repairs must not be made.

For a replacement T-5210, contact

the nearest Johnson Controls

branch office. Replacement covers

are available, order T-5210-602.

Fig. 1: T-5210

Pneumatic Temperature

Transmitter

Specifications

Summary of content (9 pages)

PAGE 1
24- 3910- 0, Rev .
PAGE 2
T-5210 Product Bulletin
PAGE 3
Fig. 2: T-5210 with Dewcel Element Replacement Cover T-5210-602 Thermal Conductive Material F-1000-182 ∗ Lb x 0.
PAGE 4
Fig. 8: Single Brass Well (See Table 3) Fig.
PAGE 5
Fig. 10: T-5210 with Averaging Element Fig.
PAGE 6
Fig. 12: T-5210 with Bulb Element and Duct Flange Fig.
PAGE 7
Fig. 14: Bulb Element Dimensions, in./mm (See Table 4) Application and Drawing Identification Fig.
PAGE 8
Fig. 16: Temperature vs. Output Pressure Calibration The T-5210 has a fixed span and is factory calibrated. The only adjustment necessary is for shifting the span for special applications or for fine tuning the instrument. 1. Accurately measure the temperature at the element. 2. From the graph in Fig. 17, find the proper transmission pressure corresponding to the measured temperature. Be sure to use the vertical scale on the graph which matches the range of the transmitter. 3.
PAGE 9
Building Efficiency 507 E. Michigan Street, Milwaukee, WI 53202 Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc. All other marks herein are the marks of their respective owners.