Install Instructions

ManualsBrandsJohnson Controls ManualsHeating SuppliesTemp Sensor - 1K Nickel OHM w/ Phone Jack, Dual Setpoint, Scaled & Liquid Bulb Thermometer

Installation Instructions TE-6700

Issue Date April 17, 2007

Part No. 24-7701-209, Rev. B www.johnsoncontrols.com

TE-6700 Series 2nd Generation Temperature Elements

Installation

Refer to the Mounting section for a complete list of

tools required for installation of both surface and

wallbox mounting styles.

Parts Included

• mounting base for U.S. wallbox or surface

mounting

• No. 6-32 x 7/8 in. (22 mm) oval-head screw (2)

• No. 4-40 x 1/4 in. (6.4 mm) hex-head cover screw

(comes installed)

• drywall clip mounting kit (includes two each

No. 6-20 x 1-1/4 in. (32 mm) pan-head, tapping

screws, spring clips, and spacers)

IMPORTANT: Do not remove the Printed

Circuit Board. Removing the Printed Circuit Board

voids the product warranty.

IMPORTANT: Use this TE-6700 Series 2nd

Generation Temperature Element only to provide

input to equipment under normal operating

conditions. Where failure or malfunction of the

TE-6700 Series element could lead to personal

injury or property damage to the controlled

equipment or other property, additional precautions

must be designed into the control system.

Incorporate and maintain other devices, such as

supervisory or alarm systems or safety or limit

controls intended to warn of, or protect against,

failure or malfunction of the TE-6700 Series element.

Accessories

Table 1: Accessories

Product Code Number Description

ACC-DWCLIP-0

Drywall Mounting Clip Kit (10 per package)

ACC-INSL-0*

Foam Pad Kit for Wallbox Mounting (10 per package)

ACC-INSL-1*

Foam Pad Kit for Surface Mounting (10 per package)

GRD10A-608

Plastic Guard with Baseplate and Mounting Ring

T-4000-119

Allen-head Adjustment Tool (order in multiples of 30)

TE-67L-600

Fahrenheit Label Replacement Kit

TE-67L-601

Celsius Label Replacement Kit

TE-67MB-600

Mounting Base Kit (order in multiples of 10)

TE-67D0-601**

Door Replacement Kit with Johnson Controls® logo (order in multiples of 10)

TE-67D0-602**

Door Replacement Kit without logo (order in multiples of 10)

* These foam pads help prevent drafts from entering the unit through the wall and make installation easier when mounting

on an uneven surface.

** Contains 1 original style and 1 new style door.

Summary of content (8 pages)

PAGE 1
Installation Instructions Issue Date TE-6700 April 17, 2007 TE-6700 Series 2nd Generation Temperature Elements Installation Refer to the Mounting section for a complete list of tools required for installation of both surface and wallbox mounting styles. Parts Included • mounting base for U.S. wallbox or surface mounting • No. 6-32 x 7/8 in. (22 mm) oval-head screw (2) • No. 4-40 x 1/4 in. (6.4 mm) hex-head cover screw (comes installed) • drywall clip mounting kit (includes two each No.
PAGE 2
Mounting The TE-6700 is shipped with one mounting base for both surface and wallbox mounting. To mount the TE-6700, release the cover from the base as described in Figure 1. 2. Swing the cover 1. Loosen (do not down from the remove) the cover base. screw with a 1/16 in. (1.5 mm) Allen wrench. 2. Rotate the mounting base, so that one of the arrows on the base points up. 3. Fasten the base to the wallbox with the No. 6-32 x 7/8 in. (22 mm) screws provided.
PAGE 3
Surface Special Tools Needed • hole saw with 1-3/8 in. (35 mm) diameter blade • 1/16 in (1.5 mm) Allen wrench or T-4000-119 Allen-Head adjustment tool • drill with 1/8 in. (3 mm) drill bit Procedure To mount the surface model to drywall, refer to Figure 5 and proceed as follows: 1. Bend the top and bottom edges of the mounting base at the perforations until they break off. (See Figure 4.
PAGE 4
Wiring Manual Override ! Temperature Sensor CAUTION: Risk of Property Damage. Do not apply power to the system before checking all wiring connections. Short circuited or improperly connected wires may result in permanent damage to the equipment. sensor (Terminal 1 and Terminal 2) • setpoint (Terminal 3 and Terminal 4) • Zone Bus and Common (COM) (Terminals 6 and 7) Shielding is not required. If used, follow the system controller’s recommendations for grounding the shield.
PAGE 5
Phone Jack Wiring (TE-67xP Models) The phone jack connection is shown in Figure 9. Make electrical connections to the rear-facing 8-pin RJ-45 connector, using eight conductor standard or plenum-rated telephone cables. Terminals are identified in Table 3. Insert the phone jack connector with the proper polarity (not reversed). Misalignment can cause damage. Refer to the controller documentation to determine the appropriate cable assembly.
PAGE 6
Table 4: Controller Compatibility with LED Mode and PB Type of TE-6700 LED Mode (Figure 1) Single Setpoint LED Off* LED On Features Enabled on TE-6700 Features Recognized by Controller AHU UNT1100 Series VAV1xx or UNT1xx VMA1200 Series** VMA1400 Series** Sensor and Manual Override No Yes Yes Yes Yes Sensor, Manual Override, and LED No No No Yes Yes No PB Room Sensor Only Yes Yes Yes Yes Yes PB* Sensor and Manual Override No Yes Yes No No No PB Room Sensor Only Yes Yes
PAGE 7
To open the access door, push down on the pull tab and pull the door open. Adjust the setpoint as follows: • • For a TE-6700 with a single setpoint: Slide the adjustment lever upward to increase the setpoint (raise the space temperature) and downward to decrease the setpoint (lower the space temperature). For a TE-6700 with a dual setpoint: Use the lever on the right to adjust the cooling setpoint, and the lever on the left to adjust the heating setpoint.
PAGE 8
Technical Specifications Product TE-6700 Series 2nd Generation Temperature Elements Nickel Sensor Temperature Sensor: Temperature Coefficient: Reference Resistance: Accuracy: 1,000 ohm thin-film nickel Approximately 3 ohms per F° (5.4 ohms per C°) 1,000 ohms at 70°F (21°C) ±0.34F° at 70°F (±0.18C° at 21°C) Platinum Sensor Temperature Sensor: Temperature Coefficient: Reference Resistance: Accuracy: 1,000 ohm thin-film platinum Approximately 2 ohms per F° (3.9 ohms per C°) 1,000 ohms at 32°F (0°C) ±0.