6657H-English_Manuals 1/28/13 1:45 PM Page 1 Machine Mountable Electronic Level with Bluetooth Model No. 40-6250 Instruction Manual Congratulations on your choice of this Machine Mountable Electronic Level with Bluetooth. We suggest you read this instruction manual thoroughly before using the instrument. Save this instruction manual for future use. Additional copies are available at www.johnsonlevel.com. Bluetooth is a trademark of Bluetooth SIG, Inc. ©2013 Johnson Level & Tool - Rev.
6657H-English_Manuals 1/28/13 1:45 PM Page 2 Table of Contents 1. Kit Contents 2. Features and Functions 3. Safety Instructions 4. Location of Parts/Components 5. Operating Instructions 6. Using the Remote Control/Receiver 7. Technical Specifications 8. Care and Handling 9. Product Warranty 10. Warranty Registration 1. Kit Contents Model No.
6657H-English_Manuals 1/28/13 1:45 PM Page 3 3. Safety Instructions Please read and understand all of the following instructions, prior to using this tool. Failure to do so, may void the warranty. ATTENTION IMPORTANT • Read all instructions prior to operating this tool. Do not remove any labels from tool. • Always turn the tool off when not in use or left unattended for a period of time.
6657H-English_Manuals 1/28/13 1:45 PM Page 4 4. Location of Parts/Components Sensor/Slaver Remote Control/Receiver Port Scan Channel Light Red Power Light Data Transfer Port Out Supply Port Link Light Power Button Data Transfer Light 4 Dust-proof Lid Port ©2013 Johnson Level & Tool - Rev.
6657H-English_Manuals 1/28/13 1:45 PM Page 5 5. Operating Instructions Sensor/Slaver Battery Installation The Sensor/Slaver requires 3 “AA” alkaline batteries to operate. Locate the battery door on bottom as shown in photo. Loosen screws, remove cover and install the batteries with correct polarity. Securely re-install battery door. Power On and Off Hold the power button for one second to power on the Sensor/Slaver. An audible beep and visual LED light will confirm the power is on.
657H-English_Manuals 1/28/13 1:45 PM Page 6 6. Using the Remote Control/Receiver Remote Display 1. Power Button (POW) a. Hold for one second to power up Sensor/Slaver with beep. b. Hold for two seconds to turn off Remote Control/Receiver with beep. 2. Measure Button (MEAS) a. Push button to enable measuring and lock control pad with beep and visual LED is lit. b. Push button again to disable measuring and unlock control pad with beep and visual LED is off. 6 ©2013 Johnson Level & Tool - Rev.
6657H-English_Manuals 1/28/13 1:45 PM Page 7 Note: All operation buttons will be non-responsive, except buttons 1, 2, & 7. Push the MEAS button again so light turns off to utilize buttons 3, 4 and 5 below. Begin measuring only after the link light of the Remote Control/Receiver and Sensor/Slaver are illuminated. If there is a delay in the illumination or the units are not connected, power down and then power up again. 3. Resolution Button (SEN/DEG) Pushing this button will switch resolutions a. 0.002º - 0.
6657H-English_Manuals 1/28/13 1:45 PM Page 8 3. Then press MEAS and move sensor to another desired X2 and Y2. 4. Pause MEAS again and hold same button until 3 beeps are heard for set degree 2, LCD will display “2”. 5. Remote Control/Receiver will beep when Sensor/Slaver is out of range (1 and 2). 6. To disable alert, press this button to enable 1 and 2. Note: X & Y axis must be set independently. Preset minimum and maximum alarm prior to setting on surface to be leveled. 6.
6657H-English_Manuals 1/28/13 1:45 PM Page 9 Calibration Procedure: 1. Put sensor on a flat plate (±3°) 2. Power up sensor and remote. Red LED power light is on both devices. 3. Hold the X/Y back LED icon for 5 seconds to enter calibration mode. There will be five beeps. 4. The LCD screen is flashing except for the number 1. This means you have entered calibration step 1. 5. Press the X/Y back LED icon again to enter calibration step 2. First beep acknowledges the button press.
6657H-English_Manuals 1/28/13 1:45 PM Page 10 7. Technical Specifications Operation Range Axis Resolution Repeatability Absolute Accuracy (25ºC) Temperature Drifting Response Time Operation Temperature Storage Temperature Weight Dimension Communication from Electronic Level to Remote Control Power Supply Range for Bluetooth LCD Backlight Color Battery Life -10º to +10º X axis, Y axis 0.002º, 0.01º, 0.1º, 1º < 0.005º (2δ) < 0.01º (±3º) < 0.04º (±10º) < 1” / ºC (0º) < 1.
6657H-English_Manuals 1/28/13 1:45 PM Page 11 8. Care and Handling • Store instrument in a safe and dry climate controlled environment at standard room temperature. • Do not throw, knock, or shake the instrument as this may damage the inner circuit boards. • Remote Control/Receiver IS NOT water resistant. Should the instrument come into contact with water, be sure to wipe immediately with a dry towel and discontinue use until fully dry. • Sensor/Slave IS NOT water resistant.
6657H-English_Manuals 1/28/13 1:45 PM Page 12 9. Product Warranty Johnson Level & Tool offers a one-year limited warranty on our Machine Mountable Electronic Level with Bluetooth. You can obtain a copy of the limited warranty for a Johnson Level & Tool product by contacting Johnson Level & Tool's Customer Service Department, as provided below, or by visiting our web site at www.johnsonlevel.com. The limited warranty for each product contains various limitations and exclusions.