Product Manual

ManualsBrandsJohnson Level ManualsIndustrial EquipmentLaser Precision Level

L100M MX LASER PRECISION LEVEL™

Operating instructions:

The Model L100M MX Laser Precision Level™ is a hand carried precision level with a built in LASER! This

Laser projects a beam of light from the end of the level and produces an eye visible laser dot that can be seen on

almost any surface even in direct sunlight. The laser actually extends the level reference to over 500 FEET and is

ten times brighter than standard red laser beams.

Here's How It Works....

1. Measure level or plumb using the precision level vial or two plumb vials. They're built in and factory

set.

2. Turn the laser on by turning the battery cap switch.

3. Mark the center of the laser dot and subtract 1/2 inch to reference the bottom of the level.

IT'S THAT SIMPLE!

Avoid Exposure

Battery Extension Level Vial Warning and Certification Label

Battery Cap 2 Plumb Vials Product Identification

ON-OFF Label

Caution - Use of controls or adjustments or performance of procedures other than those specified herein may

result in hazardous radiation exposure.

The level and plumb vials built into the L100M MX Laser Precision Level™ are used just like standard spirit

levels. Just center the bubble between the long index lines for a level indication. Remember, the more accurate the

bubble is centered between the lines, the more accurate the laser beam will be for referencing level. Note: Give

the bubble a few seconds to settle after moving the level.

Turn the laser beam on by rotating the battery compartment end cap clockwise. To turn the beam off,

turn the end cap counter-clockwise a quarter turn. Avoid over tightening since it isn't necessary. (CDRH:

The battery cap On/Off is an alternate to the beam attenuator requirement.)

The laser beam produces a bright green spot on most any reflective surface. However, the laser dot can be seen

best when the surface is of a lighter color (i.e. wooden 2x4s, white wallboards, forms, and anything colored White

or Red.) Dark colors soak up the light so the laser dot will be less bright. The L100 MX Laser Precision Level™

is bright enough to be seen in direct sunlight. The laser dot can be seen better when the sun is shaded from shining

directly onto the laser dot. Standing in front of the sun or using a sun screen (your hand, your helper’s body, a

piece of paper, etc.) will work.

Summary of content (4 pages)

PAGE 1
L100M MX LASER PRECISION LEVEL™ Operating instructions: The Model L100M MX Laser Precision Level™ is a hand carried precision level with a built in LASER! This Laser projects a beam of light from the end of the level and produces an eye visible laser dot that can be seen on almost any surface even in direct sunlight. The laser actually extends the level reference to over 500 FEET and is ten times brighter than standard red laser beams. Here's How It Works.... 1.
PAGE 2
The laser beam center is positioned 1/2 inch from the bottom of the level. This means that a half inch needs to be subtracted from the center spot of the laser dot to reference the actual bottom of the level. Mark the bull’s eye of the circular "target" and subtract 1/2 inch. This second mark is level with the bottom of the L100M MX Laser Precision Level™ within 1/8 inch out to 100 feet or any distance in between! Helpful hints: 1.
PAGE 3
Accessories: The L100M MX Laser Precision Level™ can be mounted to standard camera tripods for stand alone operation. However, to speed up the fine tuning of the level vial, the AP100A Leveling Adapter Plate or the AP1000 Transit Adapter Plate is recommended. Both the AP100A and AP1000 are designed with a 3 or 4 position adjustment system that quickly and accurately centers the bubble within the level.
PAGE 4
L100M MX MSHA Laser Precision Level™ with Battery Extension Warranty: This L100M MX Laser Precision Level™ is warranted to the original purchaser to be free from defects in workmanship and material. Laser Tools Co., Inc. will repair or replace any defective part, which may develop under normal and proper use within a period of one year from the date of purchase, without charge of parts and labor, once delivered, shipped prepaid to Laser Tools Co., Inc., together with proof of date and place of purchase.