JOLIMARK NAIL PRINTER INSTRUCTION MANUAL NP311D 1 AIS CONFIDENTIAL
Contents Foreword 1.1 Warnings Installation guide 2.1 Unpacking 2.2 Package contents 2.3 Product placement and environment 2.4 Product Movement Product settings 3.1 Product Introduction 3.2 Power On 3.3 Connect to WIFI 3.4 Nail printer APP Introduction 3.5 Installation and replacement of ink cartridge 3.6 Ink cartridge testing and maintenance 3.7 Camera calibration 3.8 Printing position calibration 3.9 Start a printing job Gel description 4.1 Gel type 4.2 gel description 4.
Customer support 8.1 Customer Support Product safety instructions 9.1 Product Safety Instructions Certificate 10.
FOREWORD This manual mainly serves as a guide to provide basic operating procedures and precautions for the users when using the product to avoid problems such as product circuit abnormality, electric shock, fire hazard, operator injury and damage caused by improper use of the product.
Installation Guide Thank you for purchasing the Jolimark Nail Printer (the Product), please follow the instructions below to install and use this product. 2.1 Unpacking 1. Open the packaging box 2. Remove the packaging (cushioning) materials 3. Take out the product 2.2 Package contents 1. A Nail Printer 2. A set of power adapter and power cord 3. An accessory box (including) : - 8 bottles of nail gel - One piece of Ink cartridge - One piece if nail holder 2.
Figure 3.1 Parts of the product 3.2 Power On To use this product, first insert the round plug of the power adapter into the DC power socket of the product and then plug in the other end of the power adapter into the AC wall socket (110V~240V). Press the power switch to turn on the power of the product. 2. Press the power switch 1. The power adapter round plug is inserted into the DC power socket of this product. 3.3 Connect to Wi-Fi 1. Press the power switch and wait for the Android tablet to boot. 2.
Press the power switch and wait for the Android tablet to boot. Touch with your finger and slide down from the top of the screen to setting screen. Select WLAN option (in red circle). Press the specified WLAN name. Press the specified WLAN name and enter the WIFI connection is completed. password. Figure 3.3 Setup WIFI 3.4 Nail printer APP Introduction 3.4.1 Variety of nail solutions for you to choose from i.
ii. You can also create your own nail plan. Click the button in the upper right corner of the page to enter the “production plan” page, fill in the name of the plan, select the picture of the ten fingers in the gallery, and then select the style of the plan to generate a unique plan. 3.4.2 Rich Manicure Gallery You can download the favorite patterns in the gallery and download the images in batches by clicking the "Download" button at the top of the page.
3.4.3 Print nail art pattern i. In the first step, the Base Gel and the Color Gel are applied in turn, and both gels need to be illuminated to dry. After drying, apply Frame Gel to the edge of the nail, no need to illuminated; Tips： You can change the lighting time by going to "App Homepage - System Management - Drying Lamp Duration"； ii. In the second step, apply the printing Gel.
Graphic requirements: printing glue (transparent / sequin / cream) does not require lighting iii. In the third step, after opening the App to select the printing scheme / picture, a printing task will be automatically generated in "Task Management". Select the finger to be printed and click the "Print" button below to enter the printing Printed pages.
[Important] When you press “Print” button to print the nail, the display screen will be locked in printing procedure, you cannot do any other process before the printing job is finished. iv. Step 4. After printing the pattern, please peel off the anti-spill adhesive on the edge of the nail, and then light it for 2 ~ 3 minutes; The fifth step is to apply reinforcement glue and sealant glue in sequence. Both glues should be illuminated for 60 seconds.
3.5 Installation and replacement of ink cartridge 3.5.1 First time installation i. Please remove the front cover when starting the product for the first time. At this time, the cartridge holder will move to the front and the indicator light will be solid yellow. Figure 3.5.1.1 Turn on and open the front cover ii. Unpack the ink cartridge and remove the blue tape Open the paper cassette and remove the Remove the ink cartridge and peel off the ink tank blue tape Figure 3.5.1.2 Remove the ink tank iii.
Figure 3.5.3 Install the ink tank iv. Note When installing the ink cartridge, do not touch the yellow probe on the ink cartridge and the surface of the wafer. Figure 3.5.4 Do not touch the ink cartridge probe point and ink cartridge chip v. After installing the ink cartridge, in the ink cartridge replacement function screen, click the Replace Complete button. Figure 3.5.5 Completing the new ink cartridge installation 3.5.
i. Open the Nail printer APP-> System Management-> Replace Ink Cartridge and click to start replacement. ii. Open the front cover and remove the ink tank. iii. To install the ink cartridge, follow the steps 2 to 5 in section 3.5.1 to complete the replacement process. 3.6 Ink cartridge print test page and ink cartridge maintenance 3.6.
holder Enter the Nail printer App, select System Printing is complete, and the printout is Management-> Print Test, and click "Start shown below. Printing" Figure 3.6.1 Ink cartridge print test 3.6.
If white lines or ink does not appear on the inkjet, refer to this section to clean the ink cartridges. i. Please refer to section 3.5.2 to remove the ink cartridge ii. Please prepare paper towels and fold them into squares iii. Hold the ink cartridge wafer down and press lightly on the paper towel. iv. Wipe the ink cartridge wafer lightly with a dry paper towel after completion v. Replacing the ink cartridge to the ink cartridge stabilizer vi.
iv. Calibration method: The upper edge of the nail holder is aligned with the upper edge of the screen, and the center of the nail holder is aligned with the calibration separator. v.
1.甲片固定座上緣 對齊螢幕上緣 2.校準豎線對齊 甲片固定座中心 攝像頭顯示移動選項 After calibration is complete, press Save to complete the camera calibration Figure 3.7 Camera calibration 3.8 Print Position Correction (Before performing this correction, please complete the camera calibration in section 3.7) When the nail print is found to be too different from the position specified by the nail app, you can refer to this chapter to correct the print position. i. Prepare a piece of printing paper that is 2.5 cm wide and 4 cm long ii.
Prepare blank paper and stick to nail holder Open the front cover and put the nail holder into the nail machine vii. Use your fingers to move the displayed test draft image, adjust its size and make the size of the displayed test draft image equal to the printed test draft image. (Two fingers: zoom on four sides; single finger: zoom on one side) viii. After adjustment, press Save to complete the print position calibration.
Open the Nail printer App, select Do not move the test draft in the screen and System Management-> Print Position press the print icon on the right Calibration 1.請勿移動測試稿位置 2.按下此圖示 After printing is completed (do not The correct position adjustment is as follows. move the nail holder), adjust the After finishing, press Save to complete the displayed test draft to be as large print correction.
Gel description 4.1 Gel type Gel name Label description UB Base Base UB Color Color layer UB Frame Spill glue UB Print-1 UBP1 UB Print-2 UBP2 UB Print-3 UBP3 UB Reinforce Anti-Spill Adhesive UB Seal Reinforce 4.
Nail Base (UB Base) Reinforcing bond strength between layers 30-60second Nail Color Layer (UB Background color as painted Color) pattern 60second Apply around nails to prevent Nail Spill Glue (UB skin contact when using nail Frame) polish No needed Nail Printing Apply on top of color glue before Adhesive (UB Print1) printing to make the printed (Transparent)* pattern clear 2-3 minutes Nail Printing Apply on top of color glue before Adhesive (UB Print2) printing to make the printed (Sequins)* patter
美甲封層膠(UB Seal) | 美甲加固膠 (UB Reinforce) 列印圖案 美甲列印膠 (UB Print) | 美甲防溢膠(UB Frame) 美甲色膠 (UB Color) 美甲底膠 (UB Base) Figure 4.3 Gluing process Specification 5.1 Product specification Table 5.1 Product Specifications Product name Nail Art Printer Model name NP311D Power Rated voltage 24Vdc specifications Rated current 2.5A Wireless Wi-Fi Wi-Fi IEEE 802.11 b/g/n connection Bluetooth Bluetooth 4.0 Width 233mm Physical Depth 177mm dimensions Height 326mm Weight 2.
Acoustic emission Sound pressure Operating Operating environment temperature Operating relative humidity Storage Storage environment temperature Storage relative humidity ≤67dB 5℃ ~ 35℃ 20% to 80% (non-condensing) -25℃ ~ 60℃ 20% ~ 93% (non-condensing) Ink cartridge specifications Ink Storage environment Dye: Ink Sealed：5℃~35℃ Unsealed：Please keep it inside the machine Proper way to place the ink cartridge Correct way Incorrect way Nail polish specifications Storage environment Shelf lif
Unsealed: one year AC power adapter The primary function of the power adapter is to convert the AC power (AC) from the wall outlet to the specific voltage DC power (DC) required by the product. Input voltage / current 100Vac – 240Vac / 50Hz –60Hz Rated voltage / current 24Vdc / 2.5A Use a power adapter that complies with the local country's certified power adapter or optional accessories for this product.
Green LED Green LED blinking USB is detected and its upgrade files are checked by the nail printer Software is upgrading Table 6-1 Display description of this product's light 6.2 Firmware upgrade i. App version upgrade In order to optimize features and user experience, the App will periodically release new versions for your use. Enter the App-System Management-Version Update page, and click the "Upgrade" button directly. If the button is gray, it means that it is the latest version. Troubleshooting 7.
Table.8-1 Customer Support Information Product safety instructions 9.1 Product Safety Instructions 1. Please read all the operation manuals. 2. This product can only be operated with the ink cartridge and accessories from original manufacturer. Do not use any unauthorized accessories or supplies. 3. Children should not use this product. 4. Please use 110V~240V as the power input voltage. 5. Do not use the power adapter for other products. 6.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
EU Declaration of Conformity Languages English Français Èeština Polski Românã Ðóññêèé Magyar Türkçe Óêðà¿íñüêà Slovenèina Deutsch Español Italiano Nederlands Português Norsk Svenska Dansk Statement This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, 2014/35/EU. Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2014/53/EU, 2014/35/EU.
forordninger i direktiv 2014/53/EU, 2014/35/EU. suomen kieli Tämä laite täyttää direktiivien 2014/53/EU, 2014/35/EU. oleelliset vaatimukset ja muut asiaankuuluvat määräykset. This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Waste Electrical and Electronic Equipment ( WEEE ) Statement This symbol on the product(s) and / or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product(s) to designated collection points where it will be accepted free of charge.
