Operation Manual

ManualsBrandsJolly Motor ManualsDomoticaJE50 RA9

enjoy motors ®

JE 50 RA 916 radio motor is a product from Jolly Motor España, s.l. www.enjoy-motors.com 1

JE50RA-916-STEEL_eng_ver. REM 2 & REM 2T

INSTRUCTIONS: how to program a radio motor or how to replace an old transmitter

ELECTRONIC TUBULAR MOTOR build in receiver ers916 “JE50 RA9”

JE50 RA9

! VERY IMPORTANT: BEFORE TO START ...

PLEASE VERIFY IN ADVANCE, WHICH IS THE VERSION OF YOUR MOTOR.

AFTER THAT, PROCEDED AS THE NEXT DIAGRAM TO CHANGE AN OLD

TRANSMITTER OR TO START WITH THE RIGHT PROCEDURE IN EACH CASE

YOU CAN FIND THE VERSION ON THE MOTOR HEAD LABEL

REM 2 916

Rev. 1.4

or previous

REM 2T 916

Rev. 1.5

or later

REM 2 916

Rev. 1.4

or previous

MOTOR IS INSTALLED

(it has its limit switch set up)

MOTOR IS NOT INSTALLED

(it hasn’t its limit switch set up)

ORIGINAL

TRANSMITTER

• doesn’t work

• it is missing

ORIGINAL

TRANSMITTER

• is working

IT HASN’T

ASSOCIATE A

TRANSMITTER

IT HAS

ASSOCIATE A

TRANSMITTER

• it works

• it doesn’t work

• it is missing

ORIGINAL

TRANSMITTER

REPLACEMENT

(9.1)

COPY STEEL

using the

original one

(7)

ASSOCIATE

THE FIRST

TRANSMITTER

(2)

ORIGINAL

TRANSMITTER

REPLACEMENT

(9.1)

PRECEDENT LIMIT SWITCHES

REMAIN WORKING

ON THE MOTOR

ENTRY ON PROGRAM MODE

TO CONTINE

(5)

DOWN LIMIT SWITCH set up

(4.1)

UP LIMIT SWITCH set up

(4.2)

MID POINT set up

(6)

MOTOR WORKS PROPERLY WITH

STEEL TRANSMITTER

MOTOR WORKS PROPERLY WITH

STEEL TRANSMITTER

REM 2T 916

Rev. 1.5

or later

MOTOR IS INSTALLED

(it has its limit switch set up)

MOTOR IS NOT INSTALLED

(it hasn’t its limit switch set up)

ORIGINAL

TRANSMITTER

• doesn’t work

• it is missing

ORIGINAL

TRANSMITTER

• is working

IT HASN’T

ASSOCIATE A

TRANSMITTER

IT HAS

ASSOCIATE A

TRANSMITTER

• it works

• it doesn’t work

• it is missing

ORIGINAL

TRANSMITTER

REPLACEMENT

(9.1)

COPY STEEL

using the

original one

(7)

ASSOCIATE

THE FIRST

TRANSMITTER

(2)

ORIGINAL

TRANSMITTER

REPLACEMENT

(9.2)

PRECEDENT LIMIT SWITCHES

REMAIN WORKING

ON THE MOTOR

ENTRY ON

PROGRAM

MODE

TO CONTINE

(5)

DOWN LIMIT SWITCH set up

(4.1)

UP LIMIT SWITCH set up

(4.2)

MID POINT set up

(6)

MOTOR WORKS PROPERLY

WITH STEEL TRANSMITTER

MOTOR WORKS PROPERLY WITH

STEEL TRANSMITTER

Summary of content (4 pages)

PAGE 1
INSTRUCTIONS: how to program a radio motor or how to replace an old transmitter ELECTRONIC TUBULAR MOTOR build in receiver ers916 “JE50 RA9” JE50 RA9 ! VERY IMPORTANT: BEFORE TO START ... PLEASE VERIFY IN ADVANCE, WHICH IS THE VERSION OF YOUR MOTOR. AFTER THAT, PROCEDED AS THE NEXT DIAGRAM TO CHANGE AN OLD TRANSMITTER OR TO START WITH THE RIGHT PROCEDURE IN EACH CASE YOU CAN FIND THE VERSION ON THE MOTOR HEAD LABEL REM 2 916 Rev. 1.4 REM 2T 916 Rev. 1.5 or previous REM 2 916 Rev. 1.
PAGE 2
INSTRUCTIONS TO: USE; SAFETY; INSTALLATION; PROGRAMMATION ELECTRONIC TUBULAR MOTOR build in receiver ers916 “JE50 RA9” JE50 RA9 2 FIRST EMITTER LEARNING (main transmitter) through a power switch OFF/ON 1 enjoy switch ON Connect the motor as the wires connect way above.
PAGE 3
LIMIT SWITCH DELETING- LOWER AND UPPER LIMIT SWITCH or also 5 ENTRY ON PROGRAM MODE hold pressing 5 ’ seconds 1/8 BIP 2/8 BIP 3/8 BIP 4/8 BIP 5/8 BIP 6/8 BIP 8/8 7/8 BIP BIP After 5 seconds holding P3 buttons, motor will make two tilt movement as Confirmation that limit switch UPPER and LOWER has been deleted Press EIGHT times the P3 button (located on the back of the emitter). Be sure to HOLD pressing on the EIGHT time.
PAGE 4
9-1 REPLACEMENT THE FIRST EMITTER (Main emitter) through the Switch Power Off/On 2 switch 2 ’’ ’ seconds minutes OFF/ON BIP Between 2 seconds and 2 minutes (and six seconds) after the power ON, the motor will make a single tilt movement as confirmation that it is ready to learn a new Main Switch power OFF, in the motor which we want replace the MAIN transmitetr.