Installation Guide

ManualsBrandsJONATHAN Y Lighting ManualsChandeliersEldora 4 Light 26" Wide LED Antler Chandelier

Item Number: JYL6301

WARNING (To reduce the risk of fire, electric shock, or injury to persons):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work

is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in

the“OFF”position. B).Place the wall switch in the “OFF” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all

side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before fixture.

6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.Please use Type "B"

Bulb max 40-watt or CFL Bulb max 13-watt or LED Bulb max 9-watt there is LED 4pcs 4-watt Bulb in

the Box.

7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.

8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as

bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that

may occur. It must be understood that common sense, caution and care must be used with any electrical

products.

IMAGE FOR FINISHED PRODUCT：

第 1 页

Summary of content (4 pages)

PAGE 1
Item Number: JYL6301 WARNING (To reduce the risk of fire, electric shock, or injury to persons): 1. We suggest installation by a licensed electrician. 2. Please read the instruction carefully and save it as you may need it at later time. 3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the“OFF”position. B).Place the wall switch in the “OFF” position. 4.
PAGE 2
TOOLS REQUIRED (NOT INCLUDED): Before doing assembly and installation please prepare the needed tools as below picture PARTS TYPE & QTY INCLUDING: (A) Plastic wire connector (3) (B) Hex nut (6) (C) Green ground screw (1) (D) Mounting plate (1) (E) Mounting screw (2) (F) Threaded nipple (2) (G)Canopy (1) (H) Screw collar loop (1) (I) Quick link (1) (J) Threaded ring (1) (K) Chain (1) (L) Loop (1) (M) Antler chandelier main body (1) (N) Trim (1) (O) Finid (1) (P) Deer-horn Stellar arm (3) (Q) Round iron plat
PAGE 3
2. Make pre‐installation Step B1: Unscrew the ball nuts(N), hex nust(B) from the antler(P). Carefully push the antler to make the threaded nipple through the hole on trim, then secure with hex nuts(B),The sleeve (R) screw into the antler chandelier main body(M), then the cover plate(Q) and the teeth are screwed ,through trim(N) into the other end of the sleeve(R),then secure with hex nuts(B).Fix the loop(L) onto the threaded nipple(F).
PAGE 4
.Make installation Step C1: Attach single bar(D) to outlet box with mounting screws(E). The side of single bar marked "GND" must face out Step C2: Raise the canopy(G) through screw collar loop(H) and screw the collar loop(J) to a proper position by measuring.Unscrew threaded ring(J) from screw collar loop(J) and remove the canopy(G). In this way, you would know the proper position on which collar loop it should be located.