Instructions / Assembly

ManualsBrandsJONATHAN Y ManualsChandeliersEldora 28.5 in. 6-Light Adjustable Resin Antler 6-Light Brown Chandelier

Item Number: JYL6302

WARNING (To reduce the risk of fire, electric shock, or injury to persons):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.

A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the

“OFF”position. B). Place the wall switch in the “OFF” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all

side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as

required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before fixture.

6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.Please use Type "B"

Bulb max 40-watt or CFL Bulb max 13-watt or LED Bulb max 9-watt there is LED 6pcs 4-watt Bulb in the Box.

7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.

8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as

bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions

that may occur. It must be understood that common sense, caution and care must be used with any

electrical products.

IMAGE FOR FINISHED PRODUCT：

第 1 页

Summary of content (4 pages)

PAGE 1
Item Number: JYL6302 WARNING (To reduce the risk of fire, electric shock, or injury to persons): 1. We suggest installation by a licensed electrician. 2. Please read the instruction carefully and save it as you may need it at later time. 3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF”position. B). Place the wall switch in the “OFF” position. 4.
PAGE 2
TOOLS REQUIRED (NOT INCLUDED): Before doing assembly and installation please prepare the needed tools as below picture PARTS TYPE & QTY INCLUDING: (A) Plastic wire connector (3) (B) Hex nut (2) (C) Green ground screw (1) (D) Mounting plate (1) (E) Mounting screw (2) (F) Threaded nipple (1) (G)Canopy (1) (H) Screw collar loop (1) (I) Quick link (2) (J) Threaded ring (1) (K) Chain (1) (L) Loop (1) (M) Antler chandelier main body (1) (N) Bulb (6) ASSEMBLY & INSTALLATION INSTRUCTIONS: 1.
PAGE 3
2. Make pre‐installation Step B1: Open the quick links (I) to connect the loops (L) on the antler chandelier main body(M), and to connect the loop(L) Close the quick links(I) Step C1: By measuring,determine the correct length of links needed. Use the chain pliers, open and discard the remaining chain. Step C2: Attach a quick link(I) to the loop(L) and to connect the end of chain(K). Step C3: Gently lace wires through chain(K) to the top of the another quick link(I) and pull tillsung 3.
PAGE 4
.Make installation Step C1: Mounting plate(D) to outlet box with mounting screws(E). The side of single bar marked "GND" must face out Step C2: Raise the canopy(G) through screw collar loop(H) and screw the collar loop(J) to a proper position by measuring.Unscrew threaded ring(J)from screw collar loop(J)and remove the canopy(G). In this way, you would know the proper position on which collar loop it should be located.