52"X H14"-19"-24" Installation video
Table of Contents Table of Contents Safety Information Warranty - - - - - - Pre-Installation - Assembly1- - - - - Option1-2 - - - - - - - - - - - - - - - - - - - - - - 2 2 3 3 8 9 Assembly- - - - - - - - Operation - - - - - - - Use of remote control Fans Balance - - - - - Care and cleaning - Troubleshooting - - - - - - - - - - - - - - - - - - 11 14 15 16 17 17 Safety Information READ AND SAVE THESE INSTRUCTIONS 1.
Warranty The supplier warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a lifetime after the date of purchase by the original purchaser. The supplier also warrants that all other fan parts, excluding any glass or acrylic blades, to be free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase by the original purchaser.
Pre-Installation(continued) TOOLS REQUIRED Phillips screwdriver Drill Electrical tape Hammer Adjustable wrench Step ladder HARDWARE INCLUDED NOTE:Hardware not shown to actual size.
Pre-Installation(continued) PACKAGE CONTENTS NOTE:Hardware not shown to actual size. A B C D A Slide-on mounting bracket 1 B Canopy 1 C 12.
Installation-Hanging the Fan 14" 19" 24" Installation - Hanging bracket For wooden ceiling, use wood screw to drill on the wooden beam or the "junction box" to fix the hanging bracket (selection is made according to actual requirements of the customers). STEP 1A-WOODEN CEILING Mounting Bracker(A) SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX. 1)Use the Mounting Bracket (A) as a guide, mark the spots where the 2 Self Mounting Screws (AA) will be drilled.
Installation - Hanging bracke t(continued) 7
Assembly1-Standard Ceiling Mount 1.Preparing for standard mounting 2.Attaching the fan to the electical box NOTE: The magnet is pre-attached on the canopy bottom cover for you to remove and install easily. WARNING: To reduce the risk of fire, electric shock or personal injury, mount to an outlet box marked “Acceptable for fan support of 35 lbs.(15.9 kg) or less," and use the screws provided with the outlet box.
Option 1-Flushmount installation (continued) 4.Flushmount Installation 3.Install flushmount assembly NOTE: If lifting is required, skip steps 3-4; if flushmount installation is required, skip steps 5-8 NOTE: Before installing the canopy, wire it first, refer to step 9 on page 11 for wiring reference ¨ Loosen the Set Screws(HH) in the ¨ Slide the canopy up into place over Support Rod Coupler(PP) located on the top center of the motor housing until the inside channel is clear.
Option 2-The Downrod installation(continued) 5.Remove the hanger ball from the downrod 6.Install Downrod and routing the wires NOTE: Equipped with two long and short suspension rods (C) and (D) for installation Choose one according to your own needs.
Assembly-Hanging the Fan 8.Hanging the fan Mounting Bracket(A) ¨ Notice the hanger ball on the end of the Down Rod is grooved down one side. This keyway fits over the small Keyway Pin(S) on the inside of the Mounting Bracket(A) and keeps the celling fan from spinning on the Mounting Bracket(A). ¨ Using your step ladder, lift the fan and place the hanger ball in the center of the Mounting Bracket(A) with the Keyway Pin(S) inserted into the keyway on the ball.
Assembly-Hanging the Fan(continued) Receiver(L) 10.Install remote control 1 ¨ Place the Receiver(L) on the Mounting Bracket(A) ¨ Carefully push the Canopy(B) to the bottom of the Mounting Bracket(A), make two sliding holes aligned to the two prominent screws on the Mounting Bracket(A), and then turn clockwise until tight.
Assembly-Attaching the Lights 13.Connecting lamp wire 14.Tighten the screw of the box cover ¨ Take the wire into the lamp shade of the ¨ Insert the“white"line in the switching box of the motorinto the“white"line of the light and tie insulated rubber tape. ¨ Insert the“Blue"line in the switching box of the motor into the“Blue"line of the light and tie insuklated rubber tape.
Operation 14
Use of remote control Fan Speed Low level Fan Speed Middle level Fan Speed High level Fan Stop Preparing the remote control Installing remote control bracket NOTE: Screw wall anchors are included for extra support. The included screws are designed to screw easily into the wall. lf you would like a more permanent or secure hold, install the wallanchors prior to attaching the wall cradle to the wall. NOTE: The frequencies on your receiver and remote contro!have been preset at the factory.
Fans Balance 1 5 2 3 4 16
Care and Cleaning Troubleshooting 16 17
