Instructions / Assembly

Table of Contents - - - - - - - - - - - - - - - - - 2
Safety Information - - - - - - - - - - - - - - - - 2
Warranty - - - - - - - - - - - - - - - - - - - - - - - 3
Pre-Installation - - - - - - - - - - - - - - - - - - 3
Assembly1- - - - - - - - - - - - - - - - - - - - - - 8
Option1-2 - - - - - - - - - - - - - - - - - - - - - - 9
Assembly- - - - - - - - - - - - - - - - - - - - - - - 11
Operation - - - - - - - - - - - - - - - - - - - - - - 14
Use of remote control - - - - - - - - - - - - - - 15
Fans Balance - - - - - - - - - - - - - - - - - - - - 16
Care and cleaning - - - - - - - - - - - - - - - - 17
Troubleshooting - - - - - - - - - - - - - - - - - - 17
Table of Contents
Safety Information
Please note changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
READ AND SAVE THESE INSTRUCTIONS
1. To reduce the risk of electric shock, ensure the electricity has been
turned off at the circuit breaker or fuse box before you begin.
2. All wiring must be in accordance with the National Electrical Code
ANSI/NFPA 70-1999 and local electrical codes. Electrical
installation should be performed by a qualified licensed electrician.
3. The outlet box and support structure must be securely mounted and
capable of reliably supporting 35 lbs (15.9 kg). Use only UL Listed
outlet boxes marked “Acceptable for Fan Support of 35 lbs (15.9 kg)
or less.”
4.CAUTlON: The fan must be mounted with a minimum of 7 ft. (2.1 m)
clearance from the trailing edge of the blades to the floor.
5. Do not operate the reversing switch while the fan blades are in
motion. You must turn the fan off and stop the blades before you
reverse the blade direction.
6. Do not place objects in the path of the blades.
7. To avoid personal injury or damage to the fan and other items, use
caution when working around or cleaning the fan.
8.Electrical diagrams are for reference only. Light kits that are not
packed with the fan must be UL-listed and marked suitable for use
with the model fan you are installing. Switches must be UL General
Use Switches. Refer to the instructions packaged with the light kits
and switches for proper assembly.
9.After making electrical connections, spliced conductors should be
turned upward and pushed carefully up into the outlet box. The
wires should be spread apart with the grounded conductor and the
equipment-grounding conductor on one side of the outlet box.
10.All setscrews must be checked and retightened where necessary
before installation.
WARNING: To reduce the risk of personal injury, do
not bend the blade brackets (also referred to as
flanges) during assembly or after installation. Do not
insert objects in the path of the blades.
WARNING: To reduce the risk of fire or electric
shock, thisfan must be installed with an isolating wall
switch.
WARNING: To avoid possible electrical shock, turn
theelectricity off at the main fuse box before wiring. lf
youfeel you do not have enough electrical wiring
knowledge orexperience, contact a licensed
electrician.
WARNING: Electrical diagrams are for reference
only.Optional use of any light kit shall be UL-listed
and markedsuitable for use with this fan.
WARNING: To reduce the risk of fire, electric shock,
or personal injury, mount to outlet box marked
“Acceptable for fan support of 35 lbs.(15.9 kg) or
less," and use the screws provided with the outlet
box.
WARNING: To reduce the risk of electrical shock or
fire ,do not use this fan with any solid-state fan speed
controdevice . lt will permanently damage the
electronic circuitry.
CAUTION: To reduce the risk of personal injury,
use only thescrews provided with the outlet box.