R CS2137 Instruction Manual Manuel d’instructions Betriebsanweisung Manual de instrucciones English Please read these instructions carefully and make sure you understand them before using this unit. Français Avant d’utiliser cet appareil, veuillez lire attentivement les instructions et assurez--vous de les avoir comprises. Deutsch Lesen Sie diese Hinweise zur Handhabung des Geräts aufmerksam durch. Verwenden Sie es erst, wenn Sie sicher sind, daß Sie alle Anweisungen verstanden haben.
IDENTIFICATION (WHAT IS WHAT?) Chain Adjustment Tool (Bar Tool) Front Handle Front Hand Guard Starter Rope Idle Speed Screw ON/STOP Switch Muffler Chain Primer Bulb Bumper Spike Bar Oil Fill Cap Starter Housing Fuel Mix Fill Cap Cylinder Cover Throttle Lockout Rear Handle Chain Direction of Travel Adjusting Screw Throttle Choke/ Trigger Fast Idle Chain Brake Lever Chain Catcher Chain Brake Nuts Guide Bar Bar Sprocket Hole IDENTIFICATION OF SYMBOLS WARNING! Read and understand the instruc
SAFETY RULES S Carefully plan your sawing operation in advance. Do not start cutting until you have a clear work area, secure footing, and, if you are felling trees, a planned retreat path. WARNING: Always disconnect spark plug wire and place wire where it cannot contact spark plug to prevent accidental starting when setting up, transporting, adjusting or making repairs except carburetor adjustments.
S Mix and pour fuel in an outdoor area on bare ground; store fuel in a cool, dry, well ventilated place; and use an approved, marked container for all fuel purposes. Wipe up all fuel spills before starting saw. S Move at least 10 feet (3 meters) from fueling site before starting engine. S Turn the engine off and let saw cool in a non-combustible area, not on dry leaves, straw, paper, etc. Slowly remove fuel cap and refuel unit.
Symmetrical Guide Bar Large Radius Tip Elbow locked S Low--Kickback Chain, designed with a contoured depth gauge and guard link which deflect kickback force and allow wood to gradually ride into the cutter. Low-Kickback Chain Contoured Depth Gauge Elongated Guard Link Deflects Kickback Force And Allows Wood To Gradually Ride Into Cutter S Handguard, designed to reduce the chance of your left hand contacting the chain if your hand slips off the front handlebar.
skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An anti-vibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool.
Adjusting the tension: Chain tension is very important. Chain stretches during use. This is especially true during the first few times you use your saw. Always check chain tension each time you use and refuel your saw. You can adjust the chain tension by loosening the chain brake nuts and turning the adjusting screw 1/4 of a turn while lifting up on the bar. S If chain is too tight, turn adjusting screw 1/4 turn counterclockwise. S If chain is too loose, turn adjusting screw 1/4 turn clockwise.
will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules relating to fuel before fueling your unit. 2. Pull the choke/fast idle lever out to the full extent. 3. Slowly press the primer bulb 6 times. 4. Pull the starter rope quickly with your right hand 5 times; then push the choke/ fast idle lever in completely (to the OFF CHOKE position). 5. Pull the starter rope quickly with your right hand until the engine starts. 6.
S The inertia activated chain brake is activated if the front hand guard is pushed forward, either manually or by centrifugal force. S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible. S When cutting with the saw, the chain brake must be disengaged. Disengaged should be placed on the ground with the engine running. Place the saw on firm ground.
NOTCH CUT AND FELLING THE TREE S Make notch cut by cutting the top of the notch first. Cut through 1/3 of the diameter of the tree. Next complete the notch by cutting the bottom of the notch. See illustration. Once the notch is cut remove the notch of wood from the tree. First cut Final cut here. 5 cm above center of notch. 5 cm Notch 5 cm Second cut S After removing the wood from the notch, make the felling cut on the opposite side of the notch.
S Roll the log over and finish with a second overcut. S Give special attention to logs under strain to prevent the saw from pinching. Make the first cut on the pressure side to relieve the stress on the log. BUCKING USING A LOG OR SUPPORT STAND S Remember your first cut is always on the pressure side of the log. S Your first cut should extend 1/3 of the diameter of the log. S Finish with your second cut. Using a log for support 2nd Cut 1st Cut 1st Cut IMPORTANT POINTS S Watch out for springpoles.
SERVICE AND ADJUSTMENTS WARNING: Disconnect the spark plug before performing maintenance, except for carburetor adjustments. We recommend all service and adjustments not listed in this manual be performed by an Authorized Service Dealer. MAINTENANCE SCHEDULE Check: Fuel mixture level . . . . Before each use Bar lubrication . . . . . . . Before each use Chain tension . . . . . . . Before each use Chain sharpness . . . . Before each use For damaged parts . . Before each use For loose caps . . . . . .
CHAIN SHARPENING STORAGE Chain sharpening is a complicated task that requires special tools. We recommend that you refer chain sharpening to a professional chain sharpener. WARNING: Stop engine and allow to cool, and secure the unit before storing or transporting in a vehicle. Store unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. Store unit with all guards in place.
DECLARATION OF CONFORMITY relating to 2000/14/EC EU Declaration of Conformity relating to 2000/14/EC We, Poulan/Weed Eater Division, Electrolux Home Products, Inc., Texarkana, TX, 75501, USA, Tél. : +1 903 223 4100, declare under sole responsibility that the Jonsered model CS2137 chain saw was assessed in accordance with Annex V of the DIRECTIVE and from serial numbers 2002--249(N or D)00001 and onwards, conforms to the provisions of the DIRECTIVE. The net power is 1,8 kW.
TECHNICAL DATA SHEET Engine Cylinder volume, cm3 Stroke, mm Idle speed, rpm Recommended max.
