3I847AW/CW Mobile Ivy Bridge 1047UE/i3/i7 + HM76 / DDR3 1333/1600 MHz HDMI / DVI / LAN / Audio /USB / PCIe mini card All-In-One Intel Mobile Ivy Bridge 1047UE/i3/i7 VGA, DVI, HDMI, PCIe mini card Multi-COM Board, Audio, LAN, SATA, USB, LVDS , Touch screen NO. 3I847AW/CW Release date: Nov.
Contents 3I847AW/CW Warning!........................................................................................................................... 1 Hardware Notice Guide ............................................................................................. 2 CHAPTER 1 GENERAL INFORMATION ........................................................................ 4 1-1 MAJOR FEATURE........................................................................................................
-11 DIGITAL INPUT / OUTPUT / WATCH DOG TIME .................................................... 32 3-11-1 IO DEVICE : F75111 UNDER DOS ....................................................................... 33 3-11-2 IO DEVICE : F75111 UNDER WINDOWS ............................................................. 34 3-11-3 IO DEVICE : F75111 VB6 UNDER WINDOWS ..................................................... 37 3-11-4 IO DEVICE : F75111 UNDER LINUX ........................................................
-8 CHIPSET .................................................................................................................... 63 4-8-1 PCH-IO CONFIGURATION ..................................................................................... 63 4-8-1-1 PCI EXPRESS CONFIGURATION ...................................................................... 64 4-8-1-1-1 MINI PCIE 1 ...................................................................................................... 64 4-8-1-2 USB CONFUGURATION ..
Copyright This manual is copyrighted and all rights are reserved. It does not allow any non authorization in copied, photocopied, translated or reproduced to any electronic or machine readable form in whole or in part without prior written consent from the manufacturer. In general, the manufacturer will not be liable for any direct, indirect, special, incidental or consequential damages arising from the use of inability to use the product or documentation, even if advised of the possibility of such damages.
Warning ! 1. Battery Battery on board is consumables. We doesn’t guarantee the life time of it. 2. Fanless solution with HDD Please be aware of specification & limitation for HDD when fanless solution is implemented. 3. We will not give further notification if there is any change about the product information and the manual. 4. SATA does not support Hot SWAP. 5. There would be +- 20% difference of WDT at room temperature. 6.
* Hardware Notice Guide 1. Before installing the power supply with this motherboard, please attach the 12V/DC ( 2 pin connector )of the adapter to motherboard first. After that, plug the adapter power to AC outlet. Always normally shut down the computer before you move the system unit or remove the power supply from the motherboard. Please unplug the 12V/DC ( 2 pin connector ) of the adapter from motherboard first. Then unplug the adapter from the AC outlet. Please refer to procedure from the photo 1 2.
Photo 1 Insert 1 2 3 Unplug 3 2 1 3
Chapter-1 General lnformation The 3I847AW/CW is a 3.5-inch compact embedded system board that features Intel® 1. Mobile Ivy Bridge 1047UE/i3/i5/i7 Processor paired with HM76 chipset to support two super speed USB 3.0 ports, and one DDR3 SO-DIMM memory socket up to 8GB DDR3 SDRAM/ 1600MHz.
1-1 Major Feature 1. Mobile Ivy Bridge 1047UE/i3/i7 Processor 2. Intel® HM76 Express Chipset 3. DDR3 up to 8GB; data transfer rates of 1333MT/s and 1600 MT/s 4. 2 x Intel® Giga LAN 5. On board SSD 2/4/8/16/32/64 GBytes (Option) 6. Support expanded PCIe Mini card for PCIe x1 and USB interface, PCIe Mini card for PCIe x1 or mSATA and USB interface 7. Support up to 4 SATA ports 8. Hardware digital Input & Output, 8 x DI / 8 x DO Hardware Watch Dog Timer, 0~255 sec programmable 9. On board DC +12V 10.
1-2 Specification 1. CPU+Chipset: 1. Intel Chief River platform; the two-chip platform consists of a Mobile Ivy Bridge 1047UE/i3/i5/i7 Processor and the Platform Controller Hub (PCH) Panther Point HM76 chipset 2. Memory: Single Channel DDR3 SODRAM 204pin, Max. 8GB, DDR3 data transfer rates of 1600 MT/s 3. VGA: Intel Mobile Ivy Bridge 1047UE Processor Integrated Graphics 4. SATA: Integrated Serial ATA Host Controller Up to 4 SATA ports: 1 SATA port 3.0 Data transfer rates up to 6.
1-3 Installing the SO-DIMM 1. Align the SO-DIMM with the connector at a 45 degree angle. 2. Press the SO-DIMM into the connector until you hear a click.
Notices: 1.The connectors are designed to ensure the correct insertion. If you feel resistance, check the connectors & golden finger direction, and realign the card. 2. Make sure the retaining clips (on two sides of the slot) lock onto the notches of the card firmly.
1-3-1.1 Removing the SO-DIMM 1. Release the SO-DIMM by pulling outward the two retaining clips and the SO-DIMM pops up slightly. 2. Lift the SO-DIMM out of its connector carefully.
1-4 Directions for installing the Mini Card 2. Plug in the Mini Card in a 45 angle 1. Unscrew the screw on the board 3. Gently push down the Mini Card and screw the screw back.
1-5 Packing List ( 3I847AW / CW ) Material Code Description Detail Specification Quantit 1 7G1901-1353001-0 MB-3I847A-3C4-00-001 LF,3I847A-3C4-00,Rev.:001 1 2 6G8006-2344-0100 DVD LF,Intel Cedarview-M/D,Sandy Bridge 1 3 6G6001-2203-0100 SATA DATA Cable (Red) LF,L=25cm 2 4 6G6001-2005-0100 COM FK LF,2.0 2*5P/DB9P,L=15cm 5 5 6G6002-8006-0100 USB RK,(USB*1 to 1*4/1.
Chapter-2 Hardware Installation This chapter provides the information how to install the hardware of 3I847AW/CW. Please follow section 1-6, 2-1 and 2-2 to check the delivery package and unpack carefully. Please follow the jumper setting procedure. 2-1 Unpacking Precaution The 3I847AW/CW board has been well packed with an anti-static bag to protect its sensitive components and circuitry from damage due to static electric discharge. NOTE! 1.
2-2 Unpacking checkup First of all, please follow all necessary steps of section 2-1 to protect 3I847AW/CW from electricity discharge. With reference to section 1-6 / 1-7 / 1-8, please check the delivery package again with following steps: 1. Unpack the 3I847AW/CW board and keep all packing material, manual and driver disc etc, do not dispose ! 2. Is there any components lose or drops from the board? DO NOT CONTINUE TO INSTALL THIS BOARD! CONTACT THE DEALER YOU PURCHASED THIS BOARD FROM, IMMEDIATELY. 3.
2-3 Dimension 145 x102 mm (3.
2-4 Layout - 3I847AW / CW CU8 CC2 JSC2 CKM1 MPCE1 JVU9 CU7 JVC1 CG1 CC1 CU1 MPCE2 CFP1 SIM1 SWP1 CU9 CU2 CPO2 FAN1 CU12 CPO1 LED1 CT1 CL2 CC6 CL1 CC5 JVL1 CPP1 CA2 CC4 JVP1 JSD1 CAR1 CA1 CC3 JVC3 CAL1 JSB2 JSB1 CIO2 CIO1 BAT1 DVI1 SIDIM1 HDMI1 CPI11 CPI13 CPI12 CO1 LVDS1 15
2-5 Diagram- 3I847AW CU8 CC2 JSC2 CKM1 MPCE1 JVU9 CU7 JVC1 CG1 CU1 CC1 MPCE2 CFP1 SIM1 SWP1 CU9 CU2 FAN1 CPO1 CU12 LED1 CT1 CL2 CC6 A CL1 CC5 JVL1 CPP1 CA2 JVP1 JSD1 CC4 CAR1 CA1 CC3 JVC3 CAL1 JSB2 JSB1 CIO2 CIO1 BAT1 DVI1 SIDIM1 HDMI1 CPI12 CO1 LVDS1 16
2-5-1 Diagram- 3I847CW CU8 CC2 JSC2 CKM1 MPCE1 JVU9 CU7 JVC1 CG1 CU1 CC1 MPCE2 CFP1 SIM1 SWP1 CU9 CU2 FAN1 CPO1 CU12 LED1 CT1 CL2 CC6 CL1 CC5 JVL1 CPP1 CA2 JVP1 JSD1 CC4 CAR1 CA1 CC3 JVC3 CAL1 JSB2 JSB1 CIO2 CIO1 BAT1 DVI1 SIDIM1 HDMI1 CPI12 CO1 LVDS1 17
2-5-2 Bottom Side Diagram- 3I847A / 3I847C COH1 COS1 CU5 CU6 SATA1 SATA2 Back Panel-3I847A / 3I847C LAN2 Mic-In LAN1 USB3.0 Line-Out USB2.
2-5-3 Bottom Side Diagram- 3I847AW / CW COH1 COS1 CU5 CU6 SATA1 SATA2 Back Panel-3I847AW / CW LAN2 Mic-In LAN1 USB3.0 Line-Out USB2.
2-6 Install Memory This motherboard provides one 204-pin Small Outline Dual In-line Memory Module (SODIMM) socket for memory expansion available maximum to of 2GB/4GB/8GB DDR3 SDRAM. DDR3 clock supports: DDR3 1333/1600MT/S Valid Memory Configurations Total Memory DIMM1 DS/SS System Accept or Not 8GB Accept DS: Double Sided DIMM Max. SS: Single Sided DIMM NOTE! The detected memory size is less than actual installed memory size since some memory has been allocated for system use.
NOTE! When you install SODIMM module fully into the SODIMM socket, the eject tab should be locked into the SODIMM module very firmly and fit into its indention on both sides. WARNING! Once you hear " Beep Beep Beep" sounds after turning on the power , please check if the DRAM is installed properly or not.
2-8 Jumper Setting Description A jumper is ON as a closed circuit with a plastic cap covering two pins. A jumper is OFF as an open circuit without the plastic cap. Some jumpers have three pins, labeled 1, 2, and 3. You could connect either pin 1 and 2 or 2 and 3. The below figure 2.2 shows the examples of different jumper settings in this manual. Figure 2.2 All jumpers already have its default setting with the plastic cap inserted as ON, or without the plastic cap as OFF.
JSB1: CMOS Data Clear JSB1 *open short Description Normal Set CMOS Data clear Note: Do not clear CMOS unless 1. Troubleshooting 2. Forget password 3. You fail over-clocking system Note：Normal work is open jumper JSB1 2 1 *Normal 2 1 Clear Setting 2-10 JSB2：ME RTC Data clear A battery must be used to retain the motherboard configuration in ME RAM. Close Pin1 and pin 2 of JSB2 to store the ME data. To clear the ME,follow the procedures below: 1. Turn off the system and unplug teh AC power 2.
2-11 JSC2：COM2 RS422/RS485 select JSC2 DESCRIPION *1-2 RS422 3-4 RS485 Note：RS422/485 setting by both H/W jumper and BIOS CMOS setting JSC2 2 1 3 4 2 1 *RS422 RS485 2-12 JSD1：DPC Duty set JSD1 DESCRIPION 1-2 Low 0% (Low level ) *2-3 Hi 100% (3.3V level) Note：For Panel backlight dimming default active set JSD1 3 2 1 3 2 1 Low level *3.
2-13 COM port pin9 select RI signal or Voltage source JVC1：COM1 PIN9 select JVC1/3 *1-2 3-4 5-6 JVC3：COM3 PIN9 select Descripion COM port pin9 use RI signal COM port pin9 use +5V voltage COM port pin9 use +12V voltage Note：1. Note：Attention ! Check Device Power in spec 2. If want to use +5V/+12V need check system power design spec 2 4 6 2 4 6 2 4 6 1 3 5 1 3 5 1 3 5 JVC1 1 3 5 JVC3 2 4 6 1 3 5 *RI signal +5V 2-14 JVL1：LCD panel power select JVL1 Descripion 1-2 +5V *2-3 +3.
2-15 JVP1：LVDS panel Inverter power select JVP1 1-2 *2-3 Descripion +12V +5V Note：Attention ! Check Device Power in spec JVP1 3 2 1 3 2 1 +12V *+5V 2-16 JVU9：USB Port 9 Voltage select JVU9 *1-2 2-3 Descripion +5V +3.3V Note：Attention ! Check Device Power in spec JVU9 1 2 3 1 2 3 *+5V +3.
Chapter-3 Connection This chapter provides all necessary information of the peripheral's connections, switches and indicators. Always power off the board before you install the peripherals. 3-1 List of Connectors CPI11：DC-in internal connector (2x2pin 4.2mm ATX connector) CPI12：DC-in 1x4 pin (2.0mm) Red wafer connector CPI13：DC-in 1x5 pin (2.0mm) wafer connector ( Option ) BAT1：Li 3V battery holder CPO1：DC +5/+12V output 1x4 pin(2.0mm) Black wafer connector CFP1：Front panel port 2x5 pin (2.
List of Connectors CU1/CU2/CU7/CU8/CU9：USB port 0/1/12/11/13 4pin(1.25mm) wafer CU12：Dual USB USB3.0/2.0 connector SATA1：SATA port 0 (Gen III) connectors 7pin SATA2：SATA port 2 (Gen II) connectors 7pin MPCE1/MPCE2：Mini card port 1/2 sockets 52pin SIM1：SIM port 1 card socket SODIM1：SO-DIM DDR3 1.
3-2 FAN Connector . FAN1：CPU FAN connector (3pin 2.5mm wafer) PIN NO. FAN1 Description 1 GND 2 +12V 3 FAN speed detect pin1 Note：DC in +12V by switch to FAN power +12V, so DC in need stable +12V input 3-3 VGA port Connector CG1 . CG1：VGA wafer (2x5pin 2.0mm wafer ) PIN NO. Description PIN NO. Description 1 BULE 2 GND 3 GND 4 DDC CLOCK 5 GREEN 6 V-SYNC 7 GND 8 H-SYNC 9 RED 10 DDC DATA 3-4 Front Panel connector . CFP1 Front panel connector (2x5pin 2.00mm wafer) PIN NO.
3-5 PS2 KB/MS . CKM1：KB/MS port 1x6pin (1.25mm) Wafer PIN NO. 1 2 3 4 5 6 Description +5V KB/DAT KB/CLK GND MS/DAT MS/CLK CKM1 pin1 3-6 USB Interface . CU5/CU6：USB4/5 ports ( USB Type A connector ) PIN NO. Description 1 +5V 2 USB DATA - 3 USB DATA + 4 GND Note : 1. Attention ! Check Device Power in spec . CU1/CU2/CU7/CU8： CU5 CU6 USB 0/1/12/11 ports (4pin 1.25mm Wafer) PIN NO. Description 1 +5V 2 USB DATA - 3 USB DATA + 4 GND pin1 CU9 . CU9：USB13 port (4pin 1.
. CU12：Dual USB3.0/2.0 port (Type A jack) PIN NO. Description 1 2 +5V USB 2.0 D- 3 4 USB 2.0 D+ GND PIN NO. 1 Description USB3.0 TX+ 2 3 4 USB3.0 TXGND USB3.0 RX+ 5 USB3.0 RX- CU12 Note：1. USB 3.0 and USB 2.0 combo Type A Jack 2. USB3.0/2.0 Keyboard and Mouse use CU12 can pitch Some OS install And wake up Keyboard and Mouse can’t work issue 3-7 LAN Interface . CL1 / CL2：LAN Giga/100Mb (RJ45 Jack) PIN NO 1 2 3 4 PIN NO.
3-8 I/O Interface . COM ports ( COM1~COM6 from support I/O ) COM1/3/4/5/6 default support RS232 mode COM2 default support RS422/RS485 mode . RS232 mode ports (2x5pin 2.0mm Wafer) CC1：COM1 CC3：COM3 CC5：COM5 CC2：COM2 CC4：COM4 CC6：COM6 PIN NO. Description 1 DCD PIN NO. 2 Description RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI/VOLTAGE 10 +5V pin1 CC2 pin1 CC1 pin1 Note：1. CC2 connector RS232 function for OEM BOM request 2. The Pin 9 Voltage set by JVC1/3 for CC1/CC3 .
2 3-9 I C Bus Interface . 2 CO1：I C(SM) bus connector (4 pin 1.25mm wafer) PIN NO. Description 1 2 3 4 +3.3V GND SMB_CLK SMB_DATA pin1 CO1 3-10 Audio interface The 3I847A / 3I847C has an on-board AC'97 3D sound interface. There are the connectors of LINE OUT, MIC-IN connectors. The MIC-IN Jack header are for audio sound input. The LINE-OUT connector is a 4-pin Jack for audio sound output. . CA1: Line out (3.5mm phone jack) PIN NO.
3-11 Digital Input / Output / Watch Dog Time . CIO1 DIO 0 ~ 3 (2x5pin 2.0mm wafer) PIN NO. Description 1 DI-0 PIN NO. 2 Description DO-3 3 DI-1 4 DO-2 5 DI-2 6 DO-1 7 DI-3 8 DO-0 9 GND 10 +5V Note：1. DI pin default pull up 10KΩ to +5V 2. If use need isolate circuit to control external device 3. F75111N-1 I2C bus address 0x9c . CIO2 DIO 4 ~ 7 (2x5pin 2.0mm wafer) PIN NO. Description PIN NO.
3-11-1 IO Device:F75111 under DOS The Sample code source you can download from Source file: F75111_Dos_Src.rar http://tprd.info/lexwiki/index.php/IO_Device:F75111_under_DOS Binary file: F75111_Dos_Bin.rar USERNAME & PASSWORD: sf How to use this Demo Application 1.Boot Ms-Dos Operating System 2.execute "75WDT.EXE" binary file 3.Input 1 to Enable WDT timer or input 0 to Disable it. 4.
3-11-2 IO Device: F75111 under Windows The Sample code source you can download from Source file: F75111_DIOSrc.rar http://tprd.info/lexwiki/index.php/IO_Device:F75111 Binary file: F75111_DemoBin.rar USERNAME & PASSWORD: sf How to use this Demo Application 1. Press the "Start" button to test DIO function 2. Press the "Enable" button to test WDT function 3. Press the "Disable" button to disable WDT 4. Check the "Enable Loop" box and press "Enable" to do WDT loop test 5.
p.s. f75111 send "F75111_SetWDTEnable(BYTE byteTimer)" including a parameter "timer", if there's no disable signal (F75111_SetWDTDisable()) to stop it before timer countdown to 0, System will reboot.
Set output value void F75111::InterDigitalOutput(BYTE byteValue) { BYTE byteData = 0; byteData = (byteData & 0x01 )? byteValue + 0x01 : byteValue; byteData = (byteData & 0x02 )? byteValue + 0x02 : byteValue; byteData = (byteData & 0x04 )? byteValue + 0x04 : byteValue; byteData = (byteData & 0x80 )? byteValue + 0x08 : byteValue; byteData = (byteData & 0x40 )? byteValue + 0x10 : byteValue; byteData = (byteData & 0x20 )? byteValue + 0x20 : byteValue; byteData = (byteData & 0x10 )? byteValue + 0x40 : byteValue;
Disable WatchDog void F75111_SetWDTDisable () { WriteByte(F75111_INTERNAL_ADDR,WDT_CONFIGURATION,0x00); // Disable WatchDog } 3-11-3 IO Device: F75111 VB6 under Windows The Sample code source you can download from Source file: 75111_VB_v10.rar http://tprd.info/lexwiki/index.php/IO_Device:F75111_VB6 Binary file: 75111_VB_Src.
SDK Function Introduction Function EnableWDT Function EnableWDT(timer As Integer) Call WriteI2CByte(&H3, &H3) Call WriteI2CByte(&H37, timer) Call WriteI2CByte(&H36, &H73) End Function Function DisableWDT Function DisableWDT() Call WriteI2CByte(&H36, &H0) End Function Function SetDOValue Function SetDOValue(dovalue As Integer) Call WriteI2CByte(&H23, &H0) Call WriteI2CByte(&H20, &HFF) Call WriteI2CByte(&H2B, &HFF) Call WriteI2CByte(&H21, dovalue) End Function Function CheckDIValue Function CheckDIValue()
3-11-4 IO Device: F75111 under linux The Sample code source you can download from Source file: F75111v2.0L.tar.gz http://tprd.info/lexwiki/index.php/IO_Device:F75111_under_linux Binary file: F75111v2.0LBin.tar.gz USERNAME & PASSWORD: sf How to compile source code 1. Compile source code with Code::Blocks download and install the Code::Block with command "apt-get install codeblocks" Open an exist project(F75111.cbp) in Code::Blocks, click the compile button ( add an option 'pkg-config --libs gtk+-2.
1. Press the "Start" button to test DIO function 2. Press the "Enable" button to test WDT function 3. Press the "Disable" button to disable WDT 4. Check the "Enable Loop" box and press "Enable" to do WDT loop test 5. Press "Install" to set the system to autorun this application when booting, press "Uninstall" to remove this application when booting. 6. If WDT enable, system icon will be blinking. p.s.
Set output value void F75111::InterDigitalOutput(BYTE byteValue) { BYTE byteData = 0; byteData = (byteData & 0x01 )? byteValue + 0x01 : byteValue; byteData = (byteData & 0x02 )? byteValue + 0x02 : byteValue; byteData = (byteData & 0x04 )? byteValue + 0x04 : byteValue; byteData = (byteData & 0x80 )? byteValue + 0x08 : byteValue; byteData = (byteData & 0x40 )? byteValue + 0x10 : byteValue; byteData = (byteData & 0x20 )? byteValue + 0x20 : byteValue; byteData = (byteData & 0x10 )? byteValue + 0x40 : byteValue;
Enable WatchDog void F75111_SetWDTEnable (BYTE byteTimer) { WriteByte(F75111_INTERNAL_ADDR,WDT_TIMER_RANGE ,byteTimer); // set WatchDog range and timer WriteByte(F75111_INTERNAL_ADDR,WDT_CONFIGURATION,WDT_TIMEOUT_FLAG | WDT_ENABLE | WDT_PULSE | WDT_PSWIDTH_100MS); // Enable WatchDog, Setting WatchDog configure } Disable WatchDog void F75111_SetWDTDisable () { WriteByte(F75111_INTERNAL_ADDR,WDT_CONFIGURATION,0x00); } 44 // Disable WatchDog
3-12 LVDS Interface Connector . LVDS1：LVDS interface (2x15 pin 1.25mm wafer) PIN NO. Description PIN NO. 1 PWM dimming 2 +5V 3 +LCD(5V or 3.3V) 4 +LCD(5V or 3.3V) 5 Channel-1-DATA3+ 6 Channel-0-DATA3+ 7 Channel-1-DATA3- 8 Channel-0-DATA3- 9 Channel-0-DATA2+ 10 Channel-0-CLK+ 11 Channel-0-DATA2- 12 Channel-0-CLK- 13 GND 14 GND 15 Channel-0-DATA1+ 16 Channel-0-DATA0+ 17 Channel-0-DATA1- 18 Channel-0-DATA0- 19 GND 20 GND 21 +LCD(5V or 3.3V) 22 +LCD(5V or 3.
3-13 Touch screen device . CT1：Touch screen (2x5 pin 2.0mm wafer) Default use USB interface, can change COM interface By OEM BOM. . For 8- wire type pin define PIN NO. Description PIN NO. Description 1 Bottom 2 Bottom Sense 3 Top Sense 4 Top 5 Right 6 Right Sense 7 Left 8 Left Sense 9 GND 10 KEY pin1 Note：1. For eight wire type cable Pin 3 and Pin4 need short. 2. Touch controller use USB port 8 . For 4- wire type pin define PIN NO. Description PIN NO.
3-14 DC power input . CPI1：DC-IN Internal Connector PIN NO. Description PIN NO. Description 1 GND 2 GND 3 NC / CAR_IN_ACC 4 DC-IN Note：1. DC in from adapter plug in 2. CPI11 Pin 3 for CPC function use for OEM option . CPI12：DC-IN Internal Connector (1 X 4 pin 2.0mm Red Wafer ) PIN NO. Description 1 GND 2 DC-IN 3 DC-IN 4 GND Note：DC in from adapter plug in . CPI13：DC-IN Internal Connector ( Option ) (1 X 5 pin 2.0mm Wafer ) PIN NO.
3-16 DC Power output . CPO1：+12V/+5V DC voltage output (4pin 2.00mm Black Wafer) PIN NO. Description 1 +5V 2 GND 3 GND 4 +12V * pin1 CPO1 *Note：DC in +12V by switch to DC-out voltage +12V, so DC in need stable +12V input 3-17 Battery Input . BAT1：3V Battery hold 2pin BAT1：Battery use Li 3V / 220mAh (CR2032) Note：1. When board without Adaptor plug in, this board power RTC consumption about 2.7uA 2. If adaptor always plug in RTC power consumption about 0.1uA BAT1 3-18 HDMI Connector .
3-19 SATA interface . SATA1/SATA2：The two SATA connectors PIN NO. Description 1 GND 2 DATA TX+ 3 DATA TX- 4 GND 5 DATA RX- 6 DATA RX+ 7 GND SATA1 SATA2 Note：1. SATA1 support SATA 3.0 spec update 6Gb/sec . 2. SATA2 support SATA 2.0 spec update 3Gb/sec . 3. CPO1 provide SATA HDD power +12V,GND ,+5V 3-20 SSD use at SATA3 channel Note：1. On board SSD for OEM option 3-21 SIM Socket . SIM1：SIM card socket pin define is follow ISO 7816-2 smart card standard. PIN NO.
3-22 Mini card & SIM card . MPCE1/MPCE2：Support USB and PCIe by one Interface (Mini card socket 52pin) PIN NO. 1 3 5 7 9 11 13 15 KEY 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 PIN NO. Description 2 NC 4 NC 6 NC 8 NC 10 GND 12 PCIe-CLK14 PCIe-CLK+ 16 GND KEY KEY 18 NC 20 NC 22 GND 24 PCIe-RX-/mSATA-RX+ 26 PCIe-RX+/mSATA-RX28 GND 30 GND 32 PCIe-TX-/mSATA-TX34 PCIe-TX+/mSATA-TX+ 36 GND 38 GND 40 +3.3V 42 +3.3V 44 NC 46 NC 48 NC 50 NC 52 mSATA-Detect Description +3.3V GND +1.
Chapter 4 Introduction of BIOS The BIOS is a program located in the Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gains control. The BIOS first operates an auto-diagnostic test called POST (Power on Self Test) for all the necessary hardware, it detects the entire hardware devices and configures the parameters of the hardware synchronization.
4-2 BIOS Menu Screen The following diagram show a general BIOS menu screen Main Advanced Chipset BIOS Vension Boot Security Save & Exit 3I847AW/CW Set the Date. Use Tab to switch between Date elements.
4-4 Getting Help Main Menu The on-line description of the highlighted setup function is displayed at the top right corner the screen. Status Page Setup Menu/ Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press .
System Date Set the Date. Please use [Tab] to switch between data elements. System Time Set the Time. Please use [Tab] to switch between data elements.
SMART Settings Please refer section 4-7-7 F71869 Super IO Configuration Please refer section 4-7-8 F71869 H/W Monitor Please refer section 4-7-9 F81216 Second Super IO Configuration Please refer section 4-7-10 Serial Port Console Redirection Please refer section 4-7-11 Network Stack Please refer section 4-7-12 4-7-1 PCI Subsystem Settings Main Advanced Chipset PCI Common Settings PCI Latency Timer Boot Security Save & Exit [32 PCI Bus Clocks] Value to be programmed into PCI Latency Timer Regis
4-7-2 ACPI Settings Main Advanced Chipset Boot Security Save & Exit Enables or Disables BIOS ACPI Auto Configuration. ACPI Settings Enable ACPI AUTO Configuration [ Disabled ] Enable Hibernation ACPI Sleep State [ Enabled ] [ S1 only(CPU Stop C..) ] →←: Select Screen ↑ ↓ : Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit Esc: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Wake system with Fixed Time Use this item to Enable or Disable system wake on alarm event. When set as Enabled, system will wake on the hour/min/sec specified. Wake system with Dynamic Time Use this item to Enable or Disable system wake on alarm event. When set as Enabled, system will wake on the current time + Increase minute(s). 4-7-4 CPU Configuration Main Advanced Chipset Boot Security CPU Configuration Intel(R) Celeron(R) CPU 1047UE @ 1.
Intel Virtualization Technology When set as Enabled, a VHM can utilize the additional hardware capabilities provided by Vanderpool Technology. The optional settings: Enabled, Disabled. 4-7-5 SATA Configuration Main Advanced Chipset Boot SATA Controller(s) SATA Mode Selection Security Save & Exit Enable or disable SATA Device. [ Enabled ] [ IDE ] →←: Select Screen ↑ ↓ : Select Item Enter: Select +/-: Change Opt.
SATA Controller Speed Indicates the maximum speed the SATA controller can support. The optional settings: Gen1, Gen2, Gen3. 4-7-6 USB Configuration Main Advanced Chipset Boot Security Save & Exit USB Configuration USB Devices: 1 Keyboard, 2 Mice, 2 Hubs Legacy USB Support USB3.0 Support XHCI Hand-off EHCI Hand-off [ Enabled ] [ Enabled ] [ Enabled ] [ Disabled ] Enables Legacy USB support AUTO option disables legacy support if no USB devices are connected.
4-7-7 SMART Settings Main Advanced Chipset Boot Security Save & Exit Smart Settings Run SMART Self Test on all HDDs during POST. Smart Self Test [ Disabled ] →←: Select Screen ↑ ↓ : Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit Esc: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc. SMART Self Test Run Smart Self Test on all HDDs during POST. The optional settings are: Disabled, Enabled.
Power Failure This item specifies whether your system will reboot after a power failure or interrupt occurs. [Keep last state] Restores the system to the status before power failure or interrupt occurred. [Bypass mode] Restores the system to the bypass mode. [Always on] Leaves the computer in the power on state. [Always off] Leaves the computer in the power off state.
4-7-9 F17869 H/W Monitor F17869 H/W Monitor Press [Enter] to view PC health status. This section shows the status of your CPU, Fan, and overall system. This is only available when there is Hardware Monitor function onboard.
4-7-10-1 Serial Port 3~6 Configuration Main Advanced Chipset Boot Security Save & Exit Serial Port 3~6 Configuration Serial Port Device Settings Enable or Disable Serial Port (COM) [ Enabled ] IO=260h; IRQ=11; Change Settings COM1 422/485 control flow [ AUTO ] [Disabled] →←: Select Screen ↑ ↓ : Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit Esc: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
4-7-11 Serial Port Console Redirection Main Advanced Chipset Boot Console Redirection ►Console Redirection Settings Security Save & Exit Console Redirection Enable or Disable. [ Disabled ] →←: Select Screen ↑ ↓ : Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit Esc: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc. Console Redirection Use this item to enable or disable Console Redirection.
4-8 Chipset Main Advanced Chipset Boot Security Save & Exit PCH Parameters ►PCH-IO Configuration ►System Agent (SA) Configuration →←: Select Screen ↑ ↓ : Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit Esc: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
4-8-1-1 ► PCI Express Configuration Main Advanced Chipset Boot Security Save & Exit PCI Express Configuration PCI Express Configuration settings ►Mini PCIe 1 ►Mini PCIe 2 →←: Select Screen ↑ ↓ : Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit Esc: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
PCIe Speed Select PCI Express port speed. The optional settings are: Auto, Gen1, Gen2. 4-8-1-2 ►USB Configuration Main Advanced Chipset Boot Security Save & Exit USB Configuration Enable or disable XHCI Pre-Boot Driver support.
xHCI Streams Use this item to enable or disable xHCI Maximum Primary Stream Array Size. The optional settings are: Disabled, Enabled. EHCI1/ EHCI2 Use this item to enable or disable USB EHCI (USB 2.0) support. One EHCI controller must always be enabled. The optional settings are: Enabled, Disabled. USB Port Pre-Port Disable Control Use this item to control each of the USB ports (0~13) disabling. The optional settings are: Disabled, Enabled.
4-8-2 ►System Agent (SA) Configuration Main Advanced Chipset Boot System Agent Bridge Name System Agent RC Version Security Save & Exit IvyBridge 1.2.0.0 Config Graphics Settings. ►Graphics Configuration →←: Select Screen ↑ ↓ : Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit Esc: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
DVMT Pre-Allocated Use this item to select DVMT 5.0 pre-allocated (fixed) graphics memory size used by the internal graphics device. The optional settings are: 32/64/96/128/160/192/224/256/288/320/352/384/416/448/480/512/1024M DVMT Total Gfx Mem Use this item to select DVMT 5.0 total graphics memory size used by the internal graphics device.
Secondary IGFX Boot Display The optional settings are: Disabled, CRT, HDMI, LVDS, DVI. LCD Panel Type This item allows you to select the panel resolution 1. VBIOS Default 2. 1024 X 600 LVDS 3. 800 X 600 LVDS 4. 1024 X 768 LVDS1 5. 1280 X 1024 LVDS 6. 1440 X 1050 (RB) LVDS1 7. 1440 X 1050 LVDS2 8. 1600 X 1200 LVDS 9. 1366 X 768 LVDS 10. 1680 X 1050 LVDS 11. 1920 X 1200 LVDS 12. 1440 X 900 LVDS 13. 1600 X 900 LVDS 14. 1024 X 768 LVDS2 15 1280 X 800 LVDS 16. 1920 X 1080 LVDS 17.
Bootup NumLock State Use this item to select keyboard NumLock State. The optional settings are: On, Off. Quiet Boot The optional settings are: Enabled, Disabled. Gate A20 Active UPON REQUEST- GA20 can be disabled using BIOS services. ALWAYS- do not allow disabling GA20.
4-10 Security Main Advanced Chipset Boot Security Save & Exit Password Description Set Administrator Password If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this Is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator right.
Chapter 5 DRIVER INSTALLATION There is a system installation DVD in the package. This DVD does not only include all the drivers you need but also some other free application programs and utility programs. In addition, this DVD also includes an auto detect software telling you which hardware is installed and which driver is needed so that your system can function properly. We call this auto detect software SYSTEM INSTALL. SYSTEM INSTALL Supports Windows XP/ Windows 7 / Windows 8 / 8.
AUTOMATIC DRIVER INSTALLATION menu 1. INF Install Intel Ivy Bridge chipset driver 2. VGA Install onboard VGA driver 3. SOUND Install VIA HD Audio Codec driver 4. LAN To the LAN driver Readme file 5. COM To the COM driver Readme file 6. USB 3.0 Install Intel USB 3.
5-1 INF Install Intel Ivy Bridge Chipset Driver 1. At the "AUTOMATIC DRIVER INSTALLATION menu" screen, click "INF". 2. At the "Intel® Chipset Device Software" screen, click "Next". 3. At the "License Agreement" screen, click "Yes". 4. At the "Readme File Information" screen, click "Next".
5. Click "Next" 6. Click "Finish" to restart computer. NOTE: SYSTEM INSTALL will auto detect file path For Windows XP 64/32-bit, Windows 7 64/32-bit and windows 8 64/32-bit X:\driver\INTEL\IVY_SAN\inf\infinst_autol.exe For Windows 8.1 64/32-bit X:\driver\INTEL\IVY_SAN\inf\WIN8.1\Setup.
5-2 VGA Install Intel Ivy Bridge VGA Driver 1. At the "AUTOMATIC DRIVER INSTALLATION menu" screen, click "VGA". 2. At the "Intel® HD Graphics Driver" screen, click "Next". 3. At the "Welcome to the Setup Program ” screen, Click “Next”. 4. At the "License Agreement” screen, Click "Next" .
5. At the "Readme File Information” screen, 6. At the "Setup Progress” screen, Click “Next”. Click “Next” 7. Click “Finish” to restart computer NOTE: SYSTEM INSTALL will auto detect file path For Windows XP 64bit X:\driver\INTEL\IVY_SAN\vga\winxp64\winxp64_145110.exe For Windows XP 32bit X:\driver\INTEL\IVY_SAN\vga\winxp\winxp_145110.exe For Windows 7 64bit and Windows 8 64bit X:\driver\INTEL\IVY_SAN\vga\ WIN_7_8_64\ win64_152812.
5-3 SOUND Install Realtek High Definition Audio Driver 1. At the "AUTOMATIC DRIVER INSTALLATION menu" screen, click "SOUND". 2. Click "Next". 3. Click "Finish" to restart computer NOTE: SYSTEM INSTALL will auto detect file path For Windows XP 32/64 bit X:\driver\INTEL\IVY_SAN\SOUND\WDM_R270.exe For Windows 7 32/64 bit and Windows 8 32/64 bit X:\driver\INTEL\IVY_SAN\SOUND\Vista_Win7_Win8_R270.exe For Windows 8.1 32bit X:\driver\INTEL\IVY_SAN\SOUND\Win8.1\32bit_Win7_Win8_Win81_R273.exe For Windows 8.
5-4 USB 3.0 Install Intel USB 3.0 extensible Host Controller Driver 1. At the "AUTOMATIC DRIVER INSTALLATION menu" screen, Click "USB 3.0". 2. At the "Intel® USB 3.0 extensible Host Controller Driver" screen, Click" Next. 3. At the "License Agreement" screen, Click "Yes". 4. At the "Readme File Information" screen, Click "Next".
5. Click "Next" 6. Click "Finish" to restart computer NOTE: The path of the file For Windows 7 32/64-bit X:\driver\INTEL\IVY_SAN\USB3_0\INTEL\Setup.
5-5 ME Install Intel Management Engine Interface Driver 1. Plaese Check Device Manager ”PCI Simple Communications Controllers” 2. At the "Intel® Management Engine Components” screen, Click” Next. 3. At the "Setup Progress” screen, Click “Next”. 4. Click “Next”.
5. Click “Finish”. 6. Plaese Check Device Manager ”PCI Simple Communications Controllers” NOTE: The path of the file For Windows XP 32/64 bit and Windows 7 32/64-bit X:\driver\INTEL\ME TOOL\MEI-Only Installer\MEISetup.
5-6 How to update AMI BIOS Step 1. To run afuwingui.exe then click "Open" Step 2.
Step 3. Choose "ProgramAll Blocks" and "Do Not Check ROM ID" Step 4. Click "Flash" Step 5. Click "Exit" and restart computer.
Appendix A: Power Consumption Test Condition Item Spec CPU Intel Ivy Bridge 1047UE 1.4 Ghz SDRAM DDR3 1333 / 1GB Operating System Windows 7 / SP1 Test Program 3D Mark Vantage HDD 3.5" SATA Standard HDD HDD 2.5" SATA Slim Type HDD Test Result for reference ! Start up Hard Disk Standard HDD Slim Type HDD Shut down Maximum In Put Voltage Maximum Stable Operation Maximum 0.06A 3.36A 1.74A 3.22A 2.23A 9V 0.06A 2.38A 1.29A 2.25A 1.68A 12V 0.06A 1.17A 0.66A 1.14A 0.
Appendix B: Resolution list 640 x 480 x ( 256 / 16bit / 32bit ) 800 x 600 x ( 256 / 16bit / 32bit ) 1024 x 768 x ( 256 / 16bit / 32bit ) 1152 x 864 x ( 256 / 16bit / 32bit ) 1280 x 600 x ( 256 / 16bit / 32bit ) 1280 x 720 x ( 256 / 16bit / 32bit ) 1280 x 768 x ( 256 / 16bit / 32bit ) 1280 x 800 x ( 256 / 16bit / 32bit ) 1280 x 960 x ( 256 / 16bit / 32bit ) 1280 x 1024 x ( 256 / 16bit / 32bit ) 1400 x 1050 x ( 256 / 16bit / 32bit ) 1440 x 900 x ( 256 / 16bit / 32bit ) 1600 x 900 x ( 256 / 16bit / 32bit ) 160
