3 3.2“ / 3.
3.2“ / 3.5“ Touch-Display TABLE OF CONTENTS 1. Overview 2. Connection 3. Installing the software 4. Using the buttons 5. Touchscreen calibration 6. Simultaneous use of LCD and HDMI 7. Information- and take-back obligations 8. Support Published: 16.08.
.2“ / 3.5“ Touch-Display 1. OVERVIEW Dear customer, Thank you very much for choosing our product. In the following we will show you what has to be observed during commissioning and use. Should you encounter any unexpected problems during use, please feel free to contact us. 3.2“ Display Controller Resolution XPT2046 320x240 Colors 2. 3.5“ Display 480x320 65.536 CONNECTION Plug the 3.2"/3.5" TFT display onto the Raspberry Pi so that it is plugged onto the first 26 pins of the GPIO connector.
3.2“ / 3.5“ Touch-Display 3. INSTALLING THE SOFTWARE Install the FBTFT image on your SD card using the "Win32 Disk Imager" program, which you can download from the following links: For RB-TFT3,2 ": Downloads 3,2" display For RB-TFT 3.5 ": Downloads 3.5" display Published: 16.08.
3.2“ / 3.5“ Touch-Display Manuelle Installation Do you already use another Raspbian Jessie Image and want this with the 3.2 "/3.5" Extend touchscreen TFT, then you can install the FBTFT modules later on your system. For this the file "config.txt" has to be edited first. Open a terminal window on your Raspberry Pi and follow the instructions: sudo nano /boot/config.txt Depending on your display, add the following lines at the beginning of the opened file: For the 3.
3.2“ / 3.5“ Touch-Display Now save the file with the key combination CTRL + O, confirm with Enter and leave the editor with the combination CTRL + X. Now the file "cmdline.txt" has to be edited: sudo nano /boot/cmdline.txt In this case, the following command must be added at the end of the already existing first line: fbcon=map:10 Save the file, exit the editor and create the file "99-calibration.conf": sudo nano /usr/share/X11/xorg.conf.d/99-calibration.
3.2“ / 3.5“ Touch-Display Now the required "drivers" are downloaded and installed. Here, the Raspberry Pi must be connected to the Internet. Enter each of the following three commands in the console and confirm each with "Enter". Commands for the 3.2 "LCD: cd /tmp wget anleitung.joy-it.net/upload/joy-IT-Display-Driver-32b-overlay.dtb sudo cp joy-IT-Display-Driver-32b-overlay.dtb /boot/overlays/joy-IT-Display-Driver32b-overlay.dtbo Commands for the 3.5 "LCD: cd /tmp wget anleitung.joy-it.
3.2“ / 3.5“ Touch-Display 5. TOUCHSCREEN KALIBRIERUNG Calibration for the 3.2 "display: If calibration of the touchscreen is necessary, this can be done with the following Steps are performed. First, the calibration tool needs to be downloaded.
3.2“ / 3.5“ Touch-Display 5. TOUCHSCREEN KALIBRIERUNG Calibration for the 3.5 "display: If calibration of the touchscreen is necessary, this can be done with the following Steps are performed. First, the calibration tool needs to be downloaded.
3.2“ / 3.5“ Touch-Display 6. GLEICHZEITIGE VERWENDUNG VON LCD UND HDMI In order to be able to output the image signal simultaneously on the TFT display and on the HDMI output, additional steps must be carried out. The first step is to compile and install the Framebuffer-Copy program using the following commands. cd /tmp sudo apt-get install -y cmake git clone https://github.com/tasanakorn/rpi-fbcp mkdir -p rpi-fbcp/build cd rpi-fbcp/build cmake ..
3.2“ / 3.5“ Touch-Display For 4: 3 resolutions: hdmi_ignore_edid=0xa5000080 hdmi_force_hotplug=1 ########################################################################### #### Resolution settings - relevant group must be commented on #### ##### 4:3 ###### ## Settings for 320x240 (native resolution of the 3.
3.2“ / 3.
3.2“ / 3.5“ Touch-Display 7. INFORMATION- AND TAKE-BACK OBLIGATIONS Symbol on electrical and electronic equipment This crossed-out dustbin means that electrical and electronic appliances do not belong in the household waste. You must return the old appliances to a collection point. Before handing over waste batteries and accumulators that are not enclosed by waste equipment must be separated from it.
3.2“ / 3.5“ Touch-Display 8. SUPPORT We are also there for you after the purchase. If you still have questions or problems, we are also available by e-mail, telephone and ticket support system. E-Mail: service@joy-it.net Ticket-System: http://support.joy-it.net Phone: +49 (0)2845 98469 – 66 (9:30 - 17:00 o‘clock) For further information please visit our website: www.joy-it.net Published: 16.08.
