User manual Radio TS2 2 2 channels Handles 2 channels Aux 2.4GHz Receiver 6 channels

ManualsBrandsJPerkins ManualsHobbyTS2+2 2-channel radio 2-channel 2.4GHz Aux handles 6-channel receiver

Table Of Contents

Product speciﬁcations are subject to change without notice.

Due to ongoing development, the actual product may vary from

images shown.

This product contains chemicals known to the State of California

to cause cancer, birth defects and other reproductive harm.

This product is not a toy! Recommended for ages 14 and

up. Adult supervision required for ages under 18 years old.

Contains small parts, keep out of reach of children 3 years of

age and younger.

To download the full Owner’s Manual

& Technical Information Guide, please

visit www.jperkins.com

Distributed in the UK by:

J Perkins Distribution Ltd,

Lenham, Kent, ME17 2DL

United Kingdom

www.jperkins.com

MADE IN CHINA

TS2+2 Quick Start Guide

Summary of content (9 pages)

PAGE 1
Product speciﬁcations are subject to change without notice. Due to ongoing development, the actual product may vary from images shown. This product contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. TS2+2 Quick Start Guide This product is not a toy! Recommended for ages 14 and up. Adult supervision required for ages under 18 years old. Contains small parts, keep out of reach of children 3 years of age and younger.
PAGE 2
Identify the transmitter’s features and function switches. 12 3 4 5 6 2 1 9 11 10 8 7 1. 2. 3. 4. 5. 6. 1 Channel 1 (right hand gimbal) Channel 2 (left hand gimbal) Channel 3 (3 position switch) Channel 4 (variable dial) Dual Rates switch for CH2 Dual Rates switch for CH1 7. 8. 9. 10. 11. 12.
PAGE 3
Getting started Remove the components from the box and ensure you have the following items: Planet 2+2 transmitter (Tx) Planet 6 channel receiver (Rx) Remove the transmitter battery cover and insert four AA alkaline cells (not included) Connect a fully charged 4.8V or 6V battery to the receiver’s “BATT” socket via a regular switch harness. If you are connecting a ESC with a BEC circuit this is to be connected to CH2 Connect the servo leads to the receiver channel outputs as required. Active channel 1-4.
PAGE 4
Turn on the receiver power and note the receiver LED will illuminate a solid red. This indicates it has successful paired with the transmitter. LED Check all controls are working as they should do. Move both sticks to check for correct movement. If the Aux 4 dial and Aux 3 channels are connected test these as well for correct operation. Servo Revers - The ability to reverse CH1 and CH2 servo directions. To reverse CH1, power off the Tx.
PAGE 5
Dual Rates (D/R) - The ability to reduce the movement of CH1 and CH2 Adjusting CH1 D/R. When the DR2 switch is in the off position full travel is given to the receiver CH1 servo output. When the DR2 switch is in the On position the travel of the servo is determine by the position on the DR2 dial on the dual rate adjuster panel. Clockwise gives you more travel, anti-clockwise gives you less. Adjusting CH2 D/R. When the DR1 switch is in the off position full travel is given to the receiver CH2 servo output.
PAGE 6
Pairing - The ability to connect the transmitter to the receiver. To Pair a new or old receiver to the transmitter, turn off the Tx power. Press and hold the Pair button on the receiver while powering on the receiver. Once power has been switched on release the Pair button and the red LED on the receiver will start to ﬂash. The receiver will stay in Pair mode for 10 seconds. Turn on the transmitter power. As soon as the red and green LEDs are illuminated press and hold the Pair button.
PAGE 7
Failsafe - The ability to set channel 1,2,3 or 4 to a predetermined position in the event of signal loss. Turn on the transmitter power, both LED`S should be illuminated. Switch on the receiver power so the LED is solid red. Both LED`s illuminated Turn On LED On Before setting the failsafe ensure all D/R are set in the off position. -Press the Pair button for 2 seconds. -LED starts to ﬂash. -You have a 3 second window to perform the following. -Set the controls to the desired position.
PAGE 8
Distributed in the UK by: J Perkins Distribution Ltd, Lenham, Kent, ME17 2DL United Kingdom www.jperkins.
PAGE 9