MODEL 753 Operator’s Manual Operator’s Manual WARNING READ AND UNDERSTAND THE OPERATOR’S MANUAL COMPLETELY BEFORE USING THIS ATTACHMENT. ASSEMBLE, TEST AND USE ONLY IN ACCORDANCE WITH THE OPERATOR’S MANUAL INSTRUCTIONS. 7918-3.JRC 20195 South Diamond Lake Road, STE 100 Rogers, MN 55374 800.966.
MODEL 753 Table of Contents 1 Operator’s Manual Introduction ................................................................................................................................................ 4 1.1 .... Application............................................................................................................................................................4 1.2 .... Navigating This Manual .........................................................................................
MODEL 753 Operator’s Manual 4 Attachment Instructions ..................................................................................................................... 16 6 Dismounting Instructions................................................................................................................... 16 5 7 8 9 Mounting Instructions ......................................................................................................................... 16 6.1 ....
1 Introduction MODEL 753 Operator’s Manual JRCO takes pride in its attachments and have designed and engineered quality, commercial built attachments designed to help you efficiently and effectively be more productive at tasks. 1.1 Application The JRCO Hooker Aerator, used for years as a front-mounted attachment for landscape aeration, is now available in a 38”, three head tow-behind version.
1.4 Owner Assistance MODEL 753 Operator’s Manual Please complete the Warranty/Product Registration at the time of purchase. You will need to fill out a new warranty card for your new unit and send it in, or you may visit our website www.jrcoinc.com and complete our online registration form. We require this information so we can keep you update to date with any important information about your attachment and provide you with the best customer service possible.
1.6 Further Assistance MODEL 753 Operator’s Manual Your dealer and all of us at JRCO want you to be pleased with your attachment. Should you require further assistance or have questions regarding your attachment, please contact your local dealer where you purchased your attachment. If you are unable to satisfy your needs by your local dealer, please contact us at: JRCO 20195 South Diamond Lake Road, STE 100 Rogers, MN 55374 800-966-8442 info@jrcoinc.com www.jrcoinc.
2 Assembly and Set-up MODEL 753 Operator’s Manual 2.1 Frame Assembly Parts 20195 South Diamond Lake Road, STE 100 Rogers, MN 55374 800.966.
MODEL 753 Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Part No. 5026.JRC 7805-2.JRC 8281.JRC 7883.JRC 7803-1.JRC 4003.JRC 4009.JRC 7278.JRC 4236.JRC 7806-1.JRC 7842-3.JRC 7809-2.JRC 7833.JRC 7914.JRC 7867.JRC 7844-1.JRC 7808.JRC 7308.JRC 4684.JRC 7811.JRC 3045.JRC 7828.
2.2 Caster Head Assembly Parts Ref 31 32 33 34 35 40 41 42 44 47 48 49 50 51 Part No. 7873.JRC 7816.JRC 8288.JRC 3047.JRC 7846.JRC 7904R.JRC 7904L.JRC 7908.JRC 7860.JRC 8267.JRC 8270.JRC 7819.JRC 7942.JRC 7823-1.
MODEL 753 2.3 Tools Required • • • • • Operator’s Manual Socket Wrench: 9/16” & ¾” Open or Box Wrench: 9/16” & ¾” Pliers Allen Wrench: 5/32” Grease gun 2.4 Power Unit Requirements The Hooker Soft-Plug Aerator is designed to be attached to the JRCO hitch for mounting on zero turn mowers, UTVs and lawn tractors. 2.5 Unpacking Your Attachment CAUTION Sharp edges Heavy Your Hooker Aerator will ship in 2 boxes. Carefully set the boxes on a flat working area.
MODEL 753 2.8 Stabilizer Frame to Tow Tongues Assembly Refer to Figure 1-1 Operator’s Manual 1. Align holes in stabilizer frame, tow tongue and aerator frame. 2. Secure with four 3/8-16 x 2 ½” hex bolts and twoway locknuts. 2.9 Pivot Arms to Actuator Mount to Extension Harness Assembly Refer to Figure 1-2 1. Insert pivot rod through two pivot arms and aerator frame using 5/8” SAE flatwashers on each side of the pivot arms. Secure with cotter pin. Figure 1-1 2.
MODEL 753 2.11 Caster Bar to Top Pivot Assembly Refer to Figure 1-4 1. Center the caster bar over aerator frame and pivot arms. Use two 3/8-16 x 2 ¾” square u-bolts and 3/816 two-way locknuts to install caster bar. 2. Attach actuator top pivot to caster bar using two 3/816 x 3 ½” hex head bolts, a 3.3” clamp bar and 3/8” two-way locknuts as show in figure 1-4. Do not tighten at this time, it will be tightened when aligned with the actuator. 2.
2.14 Mount Hitch to Tow Vehicle MODEL 753 NOTE: Park mower/UTV close to clevis area. Operator’s Manual 1. Position hitch so clevis pin slots are approximately 11 ½” from ground and slots are vertical. 2. Drill holes in hitch and attach hitch to vehicle framework or drawbar using 5/16” bolts. 2.15 Connecting Power Wire to Vehicle Battery 1. Connect supplied battery wire directly to battery terminals. Route battery cable, back to hitch, along vehicle frame.
3 Operation Instructions MODEL 753 Operator’s Manual 3.1 Before Operation Safety, hazard and accident prevention is essential. You must use awareness, concern, and proper training when operating and utilizing this attachment. You must NOT use this attachment without reading and understanding the Operator’s Manual. Make sure the operator has completed and understands the contents of this manual before operation. Refer to the chart below for key areas and ensure they are understood: 3.
3.3 Operation MODEL 753 Operator’s Manual Now you should have read your Operator’s Manual and properly attached your Hooker Aerator. Using the Hooker Aerator is simple, but there are things you need to consider before use. If you are using the attachment in an area that has large stumps, rocks, debris, exposed electrical or gas lines or foreign material that could cause damage to the attachment should be marked. You will want to avoid any sizable objects to avoid damage or injury.
4 Attachment Instructions MODEL 753 Operator’s Manual 1. Use the Hooker Aerator for its intended purposes only. Never use it to carry, push, pull or drag any object other than its intended purpose. 2. Misuse can lead to damage of the attachment. 3. Do not exceed speeds of 8 mph. 4. Mark and avoid obstacles including sprinkler heads. 5 Mounting Instructions DANGER A Crush Hazard exists when mounting attachment to mount bar. Do Not allow anyone to stand between tractor and attachment while mounting.
MODEL 753 Operator’s Manual 2. When finished cleaning dirt and debris, wash the surfaces thoroughly with a garden hose. 3. Repaint parts where paint is worn or chipped to prevent rust from forming. A coting of oil may also be applied to minimize oxidation. 4. Replaced all damaged or missing decals. 5. Store Hooker Aerators indoors if possible. Inside storage will reduce maintenance and extend life of attachment. 6. Inspect for loose or worn parts and adjust or replace as needed.
10 Maintenance Instructions MODEL 753 Operator’s Manual 10.1 General Proper servicing and adjustment is key to extending the life of your attachment. Carefully insect and routinely maintenance to avoid costly downtime and repairs. Check all bolts and nuts after using for several hours to ensure they are secure. Replace any worn, damaged or missing safety labels.
11 Specifications Model 753 Hooker Soft-Plug Aerator MODEL 753 Operator’s Manual Approximate Shipping Weight 198 lbs. Aeration Pattern 5” x 6” Aeration Width Hole Size Tines Productivity Dimensions 20195 South Diamond Lake Road, STE 100 Rogers, MN 55374 800.966.8442 38” ½” wide x 1.25” long, up to 3” dep 3/8” wide x 3” long hardened high carbon alloy steel 1.5 acres per hour @ 5 mph (66,000 sq. ft. per hour) 38.
12 Warranty 20195 South Diamond Lake Road, STE 100 Rogers, MN 55374 800.966.
