Quick Start Guide

IN THE BOX
Video Doorbell
X1
Bracket
X1
Quick Start Guide
X1
Power adapter and cable
X1
INSTALLATION OVERVIEW
LED status indicator
Microphone
Reset Button
Pair Button
Micro SD Card (TF card)
Heat emission hole
Built-in Speaker
Prior to installation, please ensure that a strong and stable Wi-Fi signal can be
achieved at the installation position. A 2.4GHz Wi-Fi connection is required.
It is recommended to charge the doorbell prior to setup. Please use a 5V/2A power
charger to reduce charging time. A 5V/2A power charger takes 4 hours to fully
charge the doorbell while a 5V/1A one takes 8 hours.
Please make sure the memory card used is CLASS10 rated.
For any further guidance, please email us at [e-mail]
HARDWARE OVERVIEW VIEDO DOORBELL
Pairing
Key
Power
ON/OFF
Pair Button
Power On/Off
Micro USB Port
To Charge Built-in Battery.
Motion Sensor
Speaker
Doorbell Button
LED Status
Indicator
Microphone
HD Camera
CONNECTION DIAGRAM_DOOR STATION
WIRELESS HUB
WiFi
Video Streaming
Video Recording
Ringtone Notification
2.4GHz
Proprietary
Push
Visitor Push
Wireless Hub transfers
the notification
to the router
Router passes
the notification
to the Internet
SETUP THE APP_IOS
Wireless Hub
X1
Screw Pack
X1
1.7
1.8
Make sure that
the Step 1.3
has been
performed and
that the hub
said Ready for
router setup.
Now click
Yes,continue
1.12
If your smart
phone is not
on the Wi-Fi,
please follow the
instruction in the
pop-up window.
1.11
Ensure the router
you wish to
connect is
2.4GHz.The
wireless hub
does not
support 5G
network,
then press
OK.
1.9
Please turn up
the volume at
least 70% above
of your smart
phone. then
swipe left.
Ensure to setup
the device
at the less noisy
environment and
keep the smart
phone to the
Wireless Hub 30cm,
then swipe left.
WiFi Setup
Add System
Add System Add System
1.10
SETUP THE APP_IOS
1.5
Please scan the
QR code label
which be placed on
the back of
wireless hub.
.
1.6
Plug in the Wireless
Hub to USB power
adaptor which
supports 5V/2A
power output. When
the Wireless Hub is
booted The Blue
status indicator will
flash slowly. And you
will hear a voice
prompt Ready for
Router Setup.
1.3
Please make
sure your smart
phone is
connected to
WiFi and mobile
data is turned off,
and then follow
QSG Step 1.5 to
1.19 to set up
the doorbell.
1.4
Open the app, and
the press + button
to add new system.
1.1
1.2
Add System Scan QR Code
Power on
Wireless Hub
Connect to
Router
Download APP
Install APP
Download and
install the
O.Connect APP
to your smart phone.
Please check the
Wi-Fi SSID is
correct and enter
the password,
then press OK.
1.14
1.13
Please select your
Wi-Fi router you’d
like to connect to,
and then press
return key to go back
to O-Connect APP.
SSID and Password
information is
necessary.
1.15
Wait for the voice:
Received router
setup
information, and
press Yes,
continue the
setup
1.16
It takes
approximately 2 mins
for wireless hub to
connect to your
home router. You will
hear a voice prompt
Router Connection
Successful once it’s
connected.Press
play to check if the
camera is present.
For your own
security
concern,
please modify
the sucurity
code of your
new added
device. Please
press “OK” for
processing.
1.17
1.18
Please modify your
security code.
Default password
“123456” is NOT
recommended.
1.19
The hub is
connected to the
internet. Press
play to check if the
camera is present.
WiFi Setup WiFi Setup
WiFi Setup WiFi Setup
Modify
Security Code
Final Check
Modify
Security Code
Internet
2.4GHz
Proprietary
WiFi
Internet sends
the notification to
the smart device
Press the
New device
button
QUICK START GUIDE
T1
Setup Work with O.connect
Version 1.7