Quick Start Guide

ManualsBrandsJSW ManualsElectronicsBattery Powered Video Doorbell

SETUP THE APP_I_ANDROID

Q&A

HOW TO ADD A NEW DEVICE

VIDEO DOORBELL INSTALLATION

2.1

2.2

Download and

install the

O.Connect APP

to your smart

phone.

2.5

Open the app, and

the press + button

to add new system,

and scan the QR

code on the

wireless hub

2.6

Please scan the

QR code label

which be placed on

the back of

wireless hub.

2.3

2.4

Please make

sure your smart

phone is

connected to

WiFi and mobile

data is turned off, a

nd then follow

QSG Step 2.5 to

2.19 to set up

the doorbell.

For your own security reason, modifing your password

regularly is recommended.

1. Press “Edit Setting” icon on the bottom of device list

page.

2. Press “Setting” icon which be above on the device.

3. Press “Advanced” icon and enter admin password

in the pop-up window for verifying.

Default Admin Password is “123456”.

4. You will be able to modify Security and Admin

password in the advance setting page.

The LED Indicator

will slowly flash

while being

charged. Once

be fully charged,

the LED status

indicator will turn

to solid light.

5V/2A USB charging port

5V/2A USB charger

If you have

changed your Wi-Fi

router, please reset

the device by

pressing the reset

button for 3 seconds

to restore to factory

default.Follow

the Quick Start

Guide “SETUP

THE APP”step

(iOS1.5~1.19/An-

droid 2.5~2.19) to

setup the device

again.

How to Reset Wireless Hub.

Please make sure wireless hub is power on and follow below steps:

Press and hold the Reset button for 3 seconds until RED status

indicator quickly flash.

Follow the Quick Start Guide “SETUP THE APP” step (iOS1.5~1.19/An-

droid 2.5~2.19) to setup the device again.

Remove the

device from

the wall mount

bracket.

Use a phillips

screwdriver to

remove the set

screw.

Install the device

to the bracket.

Confirm position

and mount the

bracket via the

screws supplied

Fasten the

screw to secure

camera and

bracket.

Mobile application

support system:

Android: 5 or later

IOS: 10 or later

NOTE

FCC/ISED WARNING

FCC Compliance Statement: This device complies with Part 15 of the FCC rules.

Operation is subjected to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This device complies with Industry Canada licence-exempt RSS standard(s).Operation

is subject to the following two conditions: (1) this device may not cause interference,

and (2) this device must accept any interference, including interference that may cause

undesired operation of the device.

Le présentappareilestconforme aux CNR d’Industrie Canada applicables aux appareils

radio exemptsde licence. L’exploitationestautorisée aux deux conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareildoit

accepter tout brouillageradioélectriquesubi, mêmesi le brouillageest susceptible

d’encompromettre le fonctionnement.

The distance between user and products should be no less than 20cm.

La distance entre l'utilisateur et de produits ne devrait pas être inférieure à 20cm.

Changes or modifications not expressly approved by the party responsible for compliance

could void your authority to operate the equipment.

Please be informed that our wireless hub supports more than one camera. If you

purchase other cameras,panic buttons and motion sensor alarms from our company,

they can work with our wireless hub. The following are steps how you can pair a

new device of our company to the wireless hub.

Press and hold the

Pair button for 3

seconds. Wireless

Hub will enter to

pairing mode.

You will hear a

voice prompt

Waiting for Device

Pairing.

The LED

status light will

quicky flash.

Pairing

Press and hold

the pair button

for 3 seconds,

The new video

doorbell will

enter pairing

mode and the

LED status

indicator will

quickly flash.

Pairing

Key

Power

ON/OFF

Charge the new

device (for example

a new video doorbell)

before pairing.

During the charging

the Blue LED will

remain on and will

turn off once charging

is complete. Unplug

the micro USB

charge cable and

power on the new

video doorbell.

Pairing

Key

Power

ON/OFF

Once pairing

completed, you

will hear a

voice prompt

Device Pairing

Successful.

The wireless

hub status

indicator will turn

to solid light.

Pairing

2.7

Press the

New device

button

2.8

Make sure that

the Step 2.3

has been

performed and

that the hub

said Ready for

router setup.

Now click

Yes,continue

2.9

Please turn

up the

volume at

least 70%

above of your

smart phone.

then swipe left.

2.10

.2 11

Ensure the

router you wish

to connect is

2.4GHz.

wireless

hub/smart

phone does not

support 5G

network. Please,

and thenpress

OK.

2.12

Check the Wi-Fi

SSID is correct,

and input

the password,

then press OK.

SETUP THE APP_ANDROID

2.15

Wait for the

voice:

Received

router setup

information,

and press

Yes, continue

the setup

2.16

It takes

approximately 2

mins for wireless

hub to connect to

your home router.

You will hear a

voice prompt

Router Connection

Successful once

it’s connected.Press

play to check if the

camera is present.

For your own

security

concern,

please modify

the sucurity

code of your

new added

device. Please

press OK for

processing.

2.17

2.18

Please modify your

security code.

Default password

“123456” is NOT

recommended.

2.19

The hub is

connected to the

internet. Press

play to check if the

camera is present.

Please select the

Wi-Fi router you’d like

to connect to and

enter password. then

press return key to go

back to O-Connect

APP.

2.13

Please check the

Wi-Fi SSID is

correct and enter

the password, then

press OK.

2.14

Add System Scan QR Code

Power on

Wireless Hub

Connect to

Router

Download APP

How to Reset

WiFi Setup

Add System

Add System Add System

WiFi Setup

WiFi Setup WiFi Setup

Modify

Security Code

Modify

Security Code

Connect the

Device

Plug in the Wireless

Hub to USB power

adaptor which

supports 5V/2A

power output. When

the Wireless Hub is

booted The Blue

status indicator will

flash slowly. And you

will hear a voice

prompt Ready for

Router Setup.

Ensure to setup

the device

at the less noisy

environment and

keep the smart

phone to the

wireless hub 30cm,

then swipe left.

How to Charge

How to Reset

How to Modify

the Password

Remove

the screw

Remove

the bracket

Bracket

installation

Device

installation

Secure device

NOTE

How to Reset

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

l Reorient or relocate the receiving antenna.

l Increase the separation between the equipment and receiver.

l Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

l Consult the dealer or an experienced radio/TV technician for help.