User's Manual

ManualsBrandsJTECH an HME ManualsElectronicsCurbside Valet

Curbside Valet

(CURBTX)

User Manual

LEE TECHNOLOGY KOREA CO., LTD.

email sales@leetek.org

website www.leetekorea.com

KOREA HEADQUARTER US OFFICE

Fl. 499-2, Sang3-dong, 530 Highland Station Drive, Suite 2004,

Wonmi-gu, Bucheon City, Sewanee, GA 30024, U.S.A.

Kyunggi-do, Korea

Tel +82-32-324-9838 Tel +1-678-714-2161

Fax +82-32-324-9840 Fax +1-678-714-2162

Summary of content (8 pages)

PAGE 1
Curbside Valet (CURBTX) User Manual LEE TECHNOLOGY KOREA CO., LTD. email sales@leetek.org website www.leetekorea.com KOREA HEADQUARTER 3rd Fl. 499-2, Sang3-dong, Wonmi-gu, Bucheon City, US OFFICE 530 Highland Station Drive, Suite 2004, Sewanee, GA 30024, U.S.A.
PAGE 2
Restroom Valet System User Manual NOTICE This manual, software and electronic circuitry are copyrighted. All rights reserved. Under the copyright laws, this manual, software and electronic circuitry may not be copied, in whole or in part without written prior consent of Lee Technology. All information provided in this document is carefully prepared and offered in good faith as a guide in the installation, use and servicing of our products.
PAGE 3
IMPORTANT SAFETY INFORMATION FCC Caution Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CE Caution Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Industry Canada Statement This device complies with Industry Canada license-exempt RSS standard(s).
PAGE 4
Safety Precautions 1. Avoid exposing this product to direct sunlight for extended periods of time, and keep it away from heat sources. 2. These is a risk of malfunction if product is used in places where sudden or extreme temperature changes occur. 3. Applying excessive force or impact to this product may result in product damage, and will void warranty. 4. Never attempt to disassemble or service this product yourself. Doing so can result in electrical shock and void warranty.
PAGE 5
1. SYSTEM INTRODUCTION 1) SYSTEM SUMMARY Using ultrasonic sensor, CURBTX is a monitoring unit that detects a vehicle standing on a certain spot and sends out a notification signal to designated pagers. The ultrasonic sensor turns on regularly and detects an object (vehicle), if it is located within 3m from the unit. 2) SPECIFICATION FEATURE BENEFIT TECHNOLOGY ° UHF Technology (450.0250 ~ 469.
PAGE 6
2. INSTALLATION 1) EQUIPMENT SETUP (1) PC Program (Manufacturer Only) ② ① ③ ④ ⑤ ⑥ ⑦ ① Select “TO GO”. ② Select COM PORT number and click “OPEN”. ③ Setup base ID (base ID should match to pagers’), (001~200, Max 3 digits) ④ Setup waiter ID (paging starts when counts reach the previously set number), (1~1249, Max 4 digits) ⑤ Signal Speed: 1200bps or 512bps ⑥ Frequency : 430.0250 ~ 469.
PAGE 7
(2) CURBTX Option Setting The option setting must be done prior to powering up. Power Switch (ON/OFF) Option Setting As shown in the photo above, there are two option switches inside the CURBTX unit. The switch on the left is to select a parking space (line) among the 16 spots assigned in the PC program, and the one on the right is to add additional options. (The current setting value in the picture above is “1000”, “0000”.
PAGE 8
(3) CURBTX Installation Insert batteries properly when the option setup above is complete. (1.5V x 3EA, D size) Use 3 alkaline batteries (1.5V, Size D). Batteries should last over two years under the condition of paging 20 times a day. A message “Startup Complete” will appear on each pager when the power is switched on. (Ensure batteries have been properly installed if no message appears on pager displays. Try to power off and on the unit again.