Lighter Smaller More Powerful GUITAR / ACCORDING / WINDS / BRASS 59508-033-04
Miniature music instruments wireless system Instruction Manual
Thank you for choosing the JTS wireless system. In order to obtain the best efficiency from the system, you are recommended to read this instruction manual carefully.
1. Important Caution 2. Features 3. Specification 01 01 02 3-1 Receiver// UR-816D (DB) 02 3-2 Miniature Transmitter// UT-16GT/UT-16GTP 02 4. Part Identification & Accessories 03 4-1 Receiver// UR-816D (DB) 03 4-2 Miniature Transmitter// UT-16GT/UT-16GTP 04 4-3 Accessories 05 5. Preparing Procedures & Basic Operation 06 5-1 Receiver 06 5-2 Battery Insertion of The Transmitter 07 5-3 Install The Transmitter 08 6. System Operation 7. Rack Mounting 8. Recommendation 9.
1. Important Caution Always make all connections before plugging the unit into an AC power outlet. Do not leave the devices in a place with high temperature or high humidity. Do not handle the power cord with wet hands! Keep the devices away from fire and heat sources. This is a general user’smanual. To check out standard accessories please find them on the product packing box. 2. Features UT-16GT/UT-16GTP provides true wireless experience to musicians.
3. Specification 3-1 Receiver// UR-816D (DB) Frequency Preparation... Carrier Frequency Range S/N Ratio.................... T.H.D......................... Display....................... Display Contents........... Controls...................... Audio Output Level....... AF Output Impedance.... Squelch....................... Operation Voltage......... Output Connector.......... PLL Synthesized Control 502~960 MHz > 105dB <0.
4. Parts Identification & Accessories 4-1 Receiver// UR-816D（DB) Front panel Antenna Power On/Off Switch Power LED Channel selector RF indicator AF indicator Volume control 1 2 3 4 5 6 7 (UR-816D) 1 4 5 6 2 3 (UR-816DB) 1 7 2 4 5 7 VOL. PLL SINGLE CHANNEL DIVERSITY RECEIVER UR-816DB POWER RF CH 11 4 5 67 10 89 AF MIN. 15 16 3 12 13 14 MAX. 12 6 10 CAUTION CAUTION RISK SHOCK RISKOF OFELECTRIC ELECTRIC SHOCK DO DONOT NOTOPEN OPEN Freq.Range Freq.
4-2 Miniature Transmitter 1 2 3 4 5 6 7 8 9 10 UT-16GT/UT-16GTP Power On/Mute/Off switch LED indicator for power On/Off, battery status and mute Channel selector Input gain Antenna 6.
4-3 Accessories 14 AC/DC adaptor A Switching Power Supply (100~240V, 50~60Hz) B Linear Power Supply (220V , 50Hz) Option C Linear Power Supply (220V , 60Hz) Option 15 AF output cable 16 Screwdriver 17 Sucker Holder 18 DR-900 dual rack adaptor 19 RP-900 panel cover Option Option 20 Adhesive tape *2 21 Windscreen 14 A B / C 15 16 17 18 19 20 (Place the adhesive tape as show in picture 1 & picture 2) 21 (Tear up the adhesive tape and position the windscreen as show in picture 3.
5. Preparing Procedures & Basic Operation 5-1 Receiver (1) Connect to the subsequent unit (e.g.
5-2 Battery Insertion Of The Transmitter (1) Press Down the battery lid 12 and slide it out. (2) Insert or replace with a new battery according to the polarity indication. (3) Switch the ON/MUTE/OFF 2 switch to ON. If the battery is in good condition the LED indicator 3 will light in Green constantly. As soon as the battery goes below a preset level the LED indicator 3 will turn to Red constantly. Then the remaining battery life will last for 30 minutes only. (4) Slide and push back the battery lid.
5-3 Install the transmitter (1) Use the UT-16GT+6.3GT plug for guitar application 1. Insert the plug to the transmitter and turn it to the end. 2. Plug the transmitter into the instrument to be used. 3. Push down the transmitter towards the instrument. The step positioning mechanism will hold the transmitter firmly on the instrument. 4. For traditional Gibson style end-mount input a sucker holder 17 is provided to prevent swiveling of the transmitter. 17 (2) Use the UT-16GTP for guitar application 1.
(2) Use the 516GT/508GT microphone module for accordion/winds/brass application 1 Insert the 516GT/508GT to the transmitter and turn it to the end. 2 Slide the 16GT Adapter/16GT CLIP/CLP-UT into the transmitter and push it to the end. 3 Fix the 16GT Adapter + 516 Bracket to the accondion by double-sided adhesive tape. 4 Fix the 16GT CLIP / CLP-UT to the instrument. 5 Adjust the 516GT/508GT to a position for desired sound performance.
(3) Setting Levels 1. Set a common frequency for both the receiver and transmitter by turning the Channel Selector 4 with supplied screw driver. 2. Turn the input gain control 5 on the transmitter to a position halfway between the left and right stops. 3. Set the ON/MUTE/OFF switch 2 to ON to switch on transmitter. 4. Switch on the receiver and sound system. 5. Turn the volume control on the transmitter to maximum level (clockwise) and play a few notes. 6.
6. System Operation Be sure to mute the audio signal of a mixer or amplifier before turning on the receiver and transmitter. (1) Power on Turn AF level on the receiver completely counter-clockwise to the minimum level, and switch on the receiver. As soon as you turn power 2 of the receiver on, the power LED 3 lights red, meanwhile the RF 5 signal and AF 6 LED light up to indicate the system is ready for operating. 2 3 5 5 2 6 VOL.
7. Rack Mounting (1) Before mount receivers onto DR-900 rack adaptor, please release any cables from the rear of the receiver. (2) Turn over receiver and DR-900 rack adaptor simultaneously, there are 4 threaded holes at the bottom of receiver and rack adaptor for inserting screws. (3) Single receiver Insert in a receiver through the front of DR-900 until it is firmly attached to the rack, then screw on a RP-900 to another side of the rack.
8. Recommendation (1) In order to achieve the optimum reception condition and also extend the operating distance, please leave on “open space” between the receiver and transmitter. (2) Keep the devices away from the metal objects or any interference sources at least 50 cm. (3) To avoid the feed-back effect, don’t leave the mic. to aim at the speakers directly. (4) Remove batteries from the battery compartment when the transmitter will not be used for a long time.
9. Important Notice (1) JTS offers wireless systems in a selection of bands that conform to the different government regulations of specific nations or geographic regions. These regulations help limit radio frequency (RF) interference among different wireless devices and prevent interference with local public communications channels, such as television and emergency broadcasts. (2) For information on bands available in your area, consult your local dealer or phone JTS.
