Manual
Table Of Contents
- DE
- 1 Zu dieser Dokumentation
- 2 Sicherheit
- 3 Beschreibung
- 4 Technische Daten
- 5 Montage
- 6 Elektrischer Anschluss
- 7 Installation
- 7.1 Funktionen
- 7.1.1 Aufbau des Bedienmenüs
- 7.1.2 Vorbereitung und Aufbau der IO-Link-Kommunikation
- 7.1.3 Teach-In-Funktion
- 7.1.4 Schaltpunkt und Schaltfunktion
- 7.1.5 Fensterfunktion, Medienerkennung und Medienunterscheidung
- 7.1.6 Schaltverzögerung
- 7.1.7 Pulsweitenmodulation
- 7.1.8 Erkennung des Verschmutzungsgrades
- 7.1.9 Auto-Kalibrierung
- 7.1 Funktionen
- 8 Parametrierung
- 9 Fehlerbehebung
- 10 Wartung und Reinigung
- 11 Außerbetriebnahme
- 12 Zubehör
- EN
- 1 About this documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Mounting
- 6 Electrical connection
- 7 Installation
- 7.1 Functions
- 7.1.1 Structure of the operating menu
- 7.1.2 Preparation and structure of IO-Link communication
- 7.1.3 Teach-In function
- 7.1.4 Switching point and switching function
- 7.1.5 Window function, media detection, and media differentiation
- 7.1.6 Switching delay
- 7.1.7 Pulse-width modulation
- 7.1.8 Detection of pollution degree
- 7.1.9 Auto-calibration
- 7.1 Functions
- 8 Parameterization
- 9 Troubleshooting
- 10 Maintenance and cleaning
- 11 Shutdown
- 12 Accessories
- FR
- 1 À propos de cette documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Montage
- 6 Raccordement électrique
- 7 Installation
- 7.1 Fonctions
- 7.1.1 Structure du menu de commande
- 7.1.2 Préparation et structure de la communication IO-Link
- 7.1.3 Fonction d'apprentissage
- 7.1.4 Point de contact et fonction de commutation
- 7.1.5 Fonction de fenêtre, reconnaissance des milieux et différenciation des milieux
- 7.1.6 Temporisation à l'enclenchement
- 7.1.7 Modulation de la largeur d'impulsion
- 7.1.8 Reconnaissance du degré de pollution
- 7.1.9 Autocalibrage
- 7.1 Fonctions
- 8 Paramétrage
- 9 Suppression des défauts
- 10 Entretien et nettoyage
- 11 Mise hors service
- 12 Accessoires
- ES
- 1 Acerca de esta documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos Técnicos
- 5 Montaje
- 6 Conexión eléctrica
- 7 Instalación
- 7.1 Funciones
- 7.1.1 Estructura del menú operativo
- 7.1.2 Preparación y configuración de la comunicación IO-Link
- 7.1.3 Función Teach-In
- 7.1.4 Punto de conmutación y función de conmutación
- 7.1.5 Función de ventana, detección de medios y distinción de medios
- 7.1.6 Retardo de conmutación
- 7.1.7 Modulación de ancho de pulso
- 7.1.8 Detección del grado de contaminación
- 7.1.9 Calibración automática
- 7.1 Funciones
- 8 Parametrización
- 9 Solución de problemas
- 10 Mantenimiento y limpieza
- 11 Desmontaje
- 12 Accesorios
- Leere Seite
21
5 Mounting
During mounting, the user should select the tightening torque, taking into account the following data:
• Relevant process connection
• Material pairing between process connection and container material
• Lubrication (for hygienic variants, e.g. NSF H1 or FDA 21 CFR 178.3570)
•Seal
• Environmental influences (e.g. pressure, temperature)
The technical regulation VDI 2230 provides assistance here.
Typically, the tightening torque is 5 to 10 Nm. If ordered from the accessories, the tightening torque is
10 Nm for the supplied welding sockets.
The sealing surfaces between the tank, container, or pipe and the device must be clean and free from
mechanical damage.
With process connection G 1/2", the device is sealed elastomer-free, without an additional seal in the
area of the device tip. If sealing is not provided via the PEEK tip, sealing tape (e.g. PTFE) in the area of
the thread is recommended.
The sealing effect of the device tip is optimum at first mounting. Mounting for test purposes is not nec-
essary.
NOTICE!
Damage to the device tip due to improper handling.
The device tip may be damaged during mounting or re-installation.
X Check the device tip for notches or grooves.
X Only use the hexagon wrench for screwing in.