Digitaler Thermostat Digital Thermostat, Thermostat numérique B 70.1050.0 Betriebsanleitung Operating Instructions, Notice de mise en service 07.
Funktionsübersicht Anzeige wechselt P > 3 Sekunden Istwertanzeige 30 Sekunden Timeout oder P + (Gleichzeitig) oder 30 Sekunden P Timeout P Code eingeben vergrößern vergrößern verkleinern verkleinern P P Bedienerebene Parameterebene Freigabeebene Parameter, die in der Freigabeebene ausgewählt wurden. Hier können werkseitig voreingestellte Parameter verändert werden. Anzeige wechselt Parameter festlegen, die in der Bedienerebene angezeigt werden oder editierbar sind.
Inhalt 1 Geräteausführung identifizieren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 Montage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Elektrischer Anschluss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1 Installationshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Geräteausführung identifizieren H Alle erforderlichen Einstellungen sind in der vorliegenden Betriebsanleitung beschrieben. Sollten trotzdem bei der Inbetriebnahme Schwierigkeiten auftreten, bitten wir Sie, keine unzulässigen Manipulationen am Gerät vorzunehmen. Sie gefährden dadurch Ihren Garantieanspruch! Bitte setzen Sie sich mit der nächsten Niederlassung oder mit dem Stammhaus in Verbindung. Lesen Sie diese Betriebsanleitung, bevor Sie das Gerät in Betrieb nehmen.
701050/ 1 2 3 4 (1) Bestellschlüssel Bestellbeispiel (2) / 701050 / 811 (3) (4) - / - 02 / 000 1 Geräteausführung identifizieren 8 9 (1)Grundausführung JUMO ecoTRON T (2) Grundtypergänzung Ausführung werkseitig eingest.,konfigurierbar innerhalb der Messeingangsgruppe nach Kundenangaben konfiguriert Messeingangsgruppe1 Pt 100 in Zweileiterschaltung Pt 1000 in Zweileiterschaltung KTY2X-6 Fe-CuNi „J“ Fe-CuNi „L“ NiCr-Ni „K“ 0 ... 20 mA 4 ... 20 mA 0 ...
Montage Demontage °C 0 (1) (2) 2 Montage 55 90 2 ≤ 75 4
3 Elektrischer Anschluss 3.1 Installationshinweise - - - Die elektromagnetische Verträglichkeit entspricht den in den technischen Daten aufgeführten Normen und Vorschriften. Das Gerät ist nicht für die Installation in explosionsgefährdeten Bereichen geeignet und muß in ein Brand- /Elektrisches Schutzgehäuse eingebaut werden.
3.
4 Gerät in Betrieb nehmen 4.1 Anzeige- und Bedienelemente 6 mm hohe dreistellige Neunsegmentanzeige und Symbole für Temperatureinheit LED K1 LED K1 leuchtet, wenn das Relais angezogen ist. LED K1 erlischt, wenn das Relais abfällt.
4.2 Gerätefunktionen einstellen (Parameterebene) H Timeout: Wird 60 Sekunden lang keine Taste bedient, schaltet das Gerät automatisch in die Istwertanzeige zurück, siehe Funktionsübersicht auf der ersten Innenseite. h 3 Sekunden lang drücken und es erscheint abwechselnd . h Code 72 für den Zugang zur Parameterebene mit den Tasten und einstellen. Je länger die Taste gedrückt wird, desto schneller verändert sich der Wert. h Mit quittieren, Parametername und Wert erscheinen abwechselnd, z.B. .
Regler Parameter Bedeutung Wertebereich von...werkseitig...bis Sollwert SP.L ... 0.0 ... SP.H Hysterese 0.2 ... 1.0 ... 99.9 Kühlen T/°C SP = 70 °C 69 °C 9 SP = 8 °C Heizen T/°C HYS HYS t Relais K1 angezogen t Relais K1 angezogen abgefallen abgefallen t t untere Sollwertgrenze Bis zu dieser unteren Grenze kann SP eingestellt werden. -999 ... -50 ... +999 obere Sollwertgrenze Bis zu dieser oberen Grenze kann SP eingestellt werden. -999 ... 500 ...
Parameter Wertebereich von...werkseitig...bis Bedeutung Einschaltverzögerungszeit nach Netz-Ein Zum zeitversetzten Einschalten mehrerer Aggregate einer Anlage. 0 ... 60min Bei Fühlerfehler wird das Relais, wie im Parameter S.Er eingestellt, sofort angesteuert. Alarme -999 ... -200 ... +999 unterer Alarmgrenzwert Sobald der Istwert diese Grenze unterschreitet, wird die Alarmmeldung in der Anzeige ausgegeben, siehe Kapitel 7 „Alarmmeldungen“. oberer Alarmgrenzwert -999 ... 500 ...
Parameter Bedeutung Wertebereich von...werkseitig...bis 0, 1 Angeschlossener Messwertgeber in Zweileiterschaltung Pt 100: Pt 1000: KTY2X-6: oder Eingang Messeingangsgruppe 1 bei Typ: 701050/X1X-1-XX Messeingangsgruppe 2 bei Typ: 701050/X2X-1-XX Fe-CuNi „J“: Fe-CuNi „L“: NiCr-Ni „K“: oder Messeingangsgruppe 3 bei Typ: 701050/X3X-1-XX 0(4)... 20 mA: / Messeingangsgruppe 4 bei Typ: 701050/X4X-1-XX 0 ... 10 V: / -999 ... 0...
Parameter Bedeutung Offset Istwert Istwert Offset in K, °F oder Digit (keine Einheit) Wertebereich von...werkseitig...bis -99,9 ... 0,0 ... 99,9 A Wenn der Gesamtwiderstand am Messeingang (Messwertgeberwiderstand + eingestellter Wert für OF.r) bei Pt100: 320 Ω und bei Pt1000/KTY2x-6: 3200 Ω überschreitet, kommt es zu einem Messfehler ! Einheit für den angezeigten Istwert A Bei Einstellung in °F wird der Istwert entsprechend umgerechnet. Alle anderen Einstellungen, wie z.
Parameter Bedeutung Wertebereich von...werkseitig...bis H Mit > 3 sec zurück zum 1. Parameter SP der Parameterebene. 4 Gerät in Betrieb nehmen Filterzeitkonstante 0,1 ... 0,8 ... 99,9 s Zur Anpassung des digitalen Eingangsfilters. Bei einem Signalsprung werden nach der Filterzeitkonstante 63% der Änderungen erfasst. Werte zwischen 0,1 und 0,7 werden als 0,8 interpretiert (Abtastzeit).
4.3 Bedienrechte vergeben (Freigabeebene) Die Einstellung in der Freigabeebene legt Bedienrechte fest, die darüber entscheiden, ob ein Parameter in der Bedienebene erscheint, editiert werden kann oder gar nicht erscheint. h 3 Sekunden lang drücken und erscheint. und h Mit quittieren Parameter und Bedienrecht blinken abwechselnd z. B. h Mit den Tasten und Bedienrecht Bedienrecht , oder einstellen. . einstellen.
Bedienen Softwareversion anzeigen P Sollwert und weitere Parameter ändern Istwertanzeige + (Beispiel) Sollwert P Weitere Parameter anzeigen (je nach eingestelltem Bedienrecht in der Freigabeebene) 5 Bedienen P oder Timeout (nach ca.
6 Technische Daten Messgenauigkeit1/ Erkennung von ... UmgebungstempeFühlerkurzFühlerbruch ratureinfluss schluss Messbereich Widerstands- Pt 100 DIN EN 60751 thermometer Pt 1000 DIN EN 60751 -200 … +600°C 0,1%/ ≤100ppm/K ja ja -200 … +600°C 0,1%/ ≤100ppm/K ja ja ja KTY2X-6 (PTC) -50 ... +150 °C 1%/ ≤100ppm/K Widerstand 0...
Messgenauigkeit1/ Erkennung von ... UmgebungstempeFühlerkurzFühlerbruch ratureinfluss schluss Messbereich Strom 0 ... 20 mA -2 ... 22 mA 0,1%/ ≤100ppm/K 3 nein skalierbar mit und oder Kundentabelle 4 ... 20 mA 2,4 ... 21,6 mA skalierbar mit und 0,1%/ ≤100ppm/K 3 ja nein ja Eingangswiderstand RE ≤ 3Ω Spannung 0 ... 10 V -1 ... 11 V 0,1%/ ≤100ppm/K skalierbar mit und oder Kundentabelle nein Eingangswiderstand RE ≥ 100kΩ 1.) Die Genauigkeiten beziehen sich auf den Messbereichsumfang. 2.
Ausgang Relais K1 (Wechselkontakt) 150.000 Schaltungen bei AC 10A/250V 50Hz ohmscher Last 800.000 Schaltungen bei AC 3A/250V 50Hz ohmscher Last Spannungsversorgung Spannungsversorgung Gehäuse Material Montage Einbaulage Gewicht Schutzart Brennbarkeitsklasse Polycarbonat Hutschiene 35mm x 7,5mm nach EN 50022 beliebig ca.
6.1 Setup Programm Das Programm und das Interface mit Adapter ist als Zubehör erhältlich und bietet folgende Möglichkeiten: - einfache und komfortable Parametrierung und Archivierung über PC - einfaches Duplizieren der Parameter bei Geräten gleichen Typs - Möglichkeit der Eingabe einer Linearisierungstabelle - PC Pentium 100 oder kompatibel - 128 MB RAM, 16 MB freier Festplattenspeicher - CD-ROM Laufwerk - freie COM-Schnittstelle - Microsoft Windows 98/ME/NT4.
7 Alarmmeldungen In der Temperaturanzeige können folgende Alarmmeldungen angezeigt werden: Fehleranzeige Ursache Abhilfe Anzeigeüberlauf Der Messwert ist zu groß und liegt außerhalb des Messbereichs. Anzeigeunterlauf Der Messwert ist zu klein und liegt außerhalb des Messbereichs. - Sensor und Anschlussleitung auf Beschädigung oder Kurzschluss überprüfen - Überprüfen, ob der richtige Sensor eingestellt oder angeschlossen ist Zeit für Einschaltverzögerung nach Netz-Ein läuft ab.
JUMO GmbH & Co. KG Hausadresse: Moltkestraße 13 - 31 36039 Fulda, Germany Lieferadresse: Mackenrodtstraße 14 36039 Fulda, Germany Postadresse: 36035 Fulda, Germany Telefon: +49 661 6003-727 Telefax: +49 661 6003-508 E-Mail: mail@jumo.net Internet: www.jumo.net JUMO JUMO Mess- und Regelgeräte Ges.m.b.H. Mess- und Regeltechnik AG Pfarrgasse 48 1232 Wien, Austria Telefon: +43 1 610610 Telefax: +43 1 6106140 E-Mail: info@jumo.at Internet: www.jumo.
Digital Thermostat B 70.1050.0 Operating Instructions 07.
Overview of operation
Contents 1 Identifying the instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 Assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.1 Installation notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Identifying the instrument The nameplate with the order code is affixed to the side of the instrument. The supply voltage connected must correspond to the voltage specified on the nameplate. All necessary settings are described in these Operation Instructions. However, if any difficulties should still arise during start-up, you are asked not to carry out any unauthorized manipulations on the unit.
701050/ 1 2 3 4 (1) Order code Order example (2) / 701050 / 811 (3) 1 Identifying the instrument 8 9 (1) Basic version JUMO ecoTRON T (2) Basic type extension Version factory-set, configurable within the measurement input group configured to customer specifications Measurement input group1 Pt 100 in 2-wire circuit Pt 1000 in 2-wire circuit KTY2X-6 Fe-Con J Fe-Con L NiCr-Ni K 0 - 20 mA 4 - 20 mA 0 - 10 V Number of relays 1 1 changeover contact 10A 250V (3) Supply 02 AC 230V +10/-15% 48 - 63Hz 05 AC
Assembling Disassembling °C 0 (1) (2) 2 Assembling 55 90 2 ≤ 75 4
3 Electrical connection 3.1 Installation notes - - - The instrument is not suitable for installation in areas with an explosion hazard and must be built into a housing that provides protection against fire /electrical hazards. Apart from faulty installation, incorrect settings on the instrument (setpoint, parameter level data) may also affect the proper functioning of controlled processes or lead to damage.
3.
4 Commissioning the instrument 4.1 Displays and controls 3-digit 9-segment display, 6 mm high, and symbols for the temperature unit LED K1 LED K1 lights up when the relay is energized. LED K1 goes out when the relay is de-energized. Keys programming increase value select operational status at enabling level decrease value select operational status at enabling level Setup interface The instrument is linked to a PC via a PC interface with TTL/RS232 converter and adapter (3-pole pins).
4.2 Setting the instrument functions (parameter level) Time-out If no key is pressed for 60 seconds, the instrument automatically switches back to process value display, see Overview of operation on the first inside page. The instrument functions and values are set at the parameter level. h Press for 3 seconds and will appear alternately. h Set code 72 for accessing the parameter level by using the The longer the key is pressed, the faster the value will change.
Controller Parameter Value range from...factory-set...to Setpoint SP.L ... 0.0 ... SP.H target value of control action (temperature value, current or voltage). Hysteresis 0.2 ... 1.0 ... 99.9 Low setpoint limit SP can be set up to this low limit. -999 ... -50 ... +999 High setpoint limit SP can be set up to this high limit. -999 ... 500 ...
Parameter Value range from...factory-set...to Meaning 0 ... 60min Minimum ON time 0 ... 999 s Minimum OFF time Here you can set the time for which the equipment unit, for instance, has to remain switched on or off. These values depend on the heating or cooling 0 ... 999 s unit being used (observe manufacturer’s specifications). In the event of a probe error, the relay is operated immediately as set in parameter S.Er. Alarms -999 ... -200 ...
Parameter Meaning Value range from...factory-set...to 0, 1 Sensor connected in 2-wire circuit Pt100: Pt1000: KTY2X-6: or Input Measurement input group 1 on Type: 701050/X1X-1-XX Measurement input group 2 on Type: 701050/X2X-1-XX Fe-Con J: Fe-Con L: NiCr-Ni K: or Measurement input group 3 on Type: 701050/X3X-1-XX 0(4)... 20 mA: / Measurement input group 4 on Type: 701050/X4X-1-XX 0 ... 10 V: / Start value for indication range with measurement input voltage or current. -999 ... 0...
Parameter Meaning -99.9 ... 0.0 ... 99.9 Lead compensation resistance 0.0 ... 0.0 ... 99.9 in Ω This value is used for compensating the resistance of the probe lead for resistance sensors and is dependent on the lead length. For best temperature measurement results, the resistance value of the probe lead has to be entered here. A If the total resistance at the measurement input (sensor resistance + selected value for OF.
Parameter Value range from...factory-set...to Meaning H Return to the first parameter SP of the parameter level by pressing > 3 sec. 4 Commissioning the instrument 0.1 ... 0.8 ... 99.9 s Filter time constant For adapting the digital input filter. At a signal step, 63% of the changes are registered after the filter time constant has elapsed. Values between 0.1 and 0.7 are interpreted as 0.8 (sampling time).
4.3 Allocating user rights (enabling level) The setting at the enabling level defines user rights which determine whether a parameter is shown at the operating level, can be edited or is not shown at all. for 3 seconds and appears. h Set code 82 for accessing the enabling level using and . h Acknowledge with Parameter and User rights blink in alternation e. g. h Use the and keys to set user right User right , . or .
5 Operation 5 Operation 15
6 Technical data Meas. input Designation Resistance Pt100 EN 60 751 thermometer Pt1000 EN 60 751 Recognition of ... Probe shortcircuit Probe break -200 to +600°C 0.1%/ ≤100ppm/°C yes yes -200 to +600°C 0.1%/ ≤100ppm/°C yes yes yes yes KTY2X-6 (PTC) -50 to +150 °C 1%/ ≤100ppm/°C Resistance 0 — 3000 Ω customer table 3 0.1%/ ≤100ppm/°C 3 = 0Ω yes Measuring current with Pt100: 0.2 mA, with Pt1000, KTY2X-6 and resistance: 0.
Meas. input Current Designation Range Meas. accuracy1/ ambient temperature error Recognition of ... Probe shortcircuit Probe break -2 to 22 mA scalable with and or customer table 0.1%/ ≤100ppm/°C 3 no no 4 to 20 mA 2.4 to 21.6 mA scalable with and 0.1%/ ≤100ppm/°C 3 yes yes -1 to 11 V scalable with and or customer table 0.1%/ ≤100ppm/°C no Input resistance RIN ≤ 3Ω Voltage 0 — 10 V no Input resistance RIN ≥ 100kΩ 1.) The accuracy refers to the measuring range span. 2.
Output Relais K1 (changeover contact) 150,000 operations at 10A/250V AC 50Hz resistive load 800,000 operations at 3A/250V AC 50Hz resistive load Supply Supply voltage Housing Material Mounting Operating position Weight Protection Flammability class polycarbonate DIN rail 35mm x 7.5mm to EN 50 022 unrestricted approx.
6.1 Setup program The program and the interface with adapter are available as accessories and offer the following advantages: - simple and convenient parameterization and archiving from a PC - simple duplicating of parameters on instruments of the same type - possibility of entering a linearization table - PC Pentium 100 or compatible - 128 MB RAM, 16 MB free on hard disk - CD-ROM drive - free COM interface - Microsoft Windows 98/ME/NT4.
7 Alarm messages The following alarm messages can be shown in the temperature display: Error message Cause Elimination Display overrun The measured value is too large and outside the range. - Check sensor and connecting cable for damage or short-circuit - Check whether the correct sensor has been set or connected Display underrun The measured value is too small and is outside the range. Time for switch-on delay after power-on has elapsed.
JUMO GmbH & Co. KG JUMO Instrument Co. Ltd. JUMO PROCESS CONTROL INC. Street adress: Moltkestraße 13 - 31 36039 Fulda, Germany Delivery address: Mackenrodtstraße 14 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 e-mail: mail@jumo.net Internet: www.jumo.net JUMO House Temple Bank, Riverway Harlow, Essex CM20 2TT, UK Phone: +44 1279 635533 Fax: +44 1279 635262 e-mail: sales@jumo.co.uk Internet: www.jumo.co.
Thermostat numérique B 70.1050.0 Notice de mise en service 07.
Aperçu des fonctions Affichage de la température P > 3 secondes L’affichage change 30 secondes Timeout ou P + (simultanément) P ou 30 secondes Timeout P Niveau “Utilisateur” Paramètres sélectionnés au niveau “Déverrouillage” Saisir le code Incrémenter Incrémenter Décrémenter Décrémenter P P Niveau “Paramétrage” Les paramètres préréglés en usine peuvent être modifiés ici.
Sommaire 1 Identification de l’appareil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 Montage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Raccordement électrique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1 Instructions à propos de l’installation . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Identification de l’appareil La plaque signalétique est collée sur la partie supérieure de l’appareil. La tension appliquée doit correspondre à celle indiquée sur la plaque signalétique. Tous les réglages et toutes les interventions éventuellement nécessaires sont décrits dans cette notice.
701050/ 8 9 2 3 4 (1) Code de commande Exemple de commande (2) / 701050 / 811 (3) (4) - / - 02 / 000 1 Identification de l’appareil 1 (1)Exécution de base JUMO ecoTRON T (2) Extension au type de base Exécution réglage d’usine, configurable configuré suivant spécifications Entrée de mesure 1 Pt 100 en montage 2 fils Pt 1000 en montage 2 fils KTY2X-6 Fe-CuNi „J“ Fe-CuNi „L“ NiCr-Ni „K“ 0 ... 20 mA 4 ... 20 mA 0 ...
Montage Démontage °C 0 (1) (2) 2 Montage 55 90 2 ≤ 75 4
3 Raccordement électrique 3.1 Instructions à propos de l’installation - - - - Tension d’alimentation 3 Raccordement électrique - Veuillez respecter la réglementation en vigueur aussi bien pour le choix du matériel des lignes, pour l’installation, que pour le raccordement électrique de l’appareil. Le raccordement électrique ne doit être effectué que par du personnel qualifié. La compatibilité électromagnétique correspond aux normes et prescriptions mentionnés dans les caractéristiques techniques.
3.
4 Mise en service de l’appareil 4.1 Affichage et commande Indicateur à 3 chiffres de 6 mm de hauteur avec symboles pour température LED K1 LED K1 s’allume lorsque le relais est excité. LED K1 s’éteint lorsque le relais est désexcité.
4.2 H Réglage des fonctions de l’appareil (niveau "Paramétrage") Fonctions et valeurs sont réglées au niveau "Paramétrage". h Appuyer sur la touche pendant 3 s et s’affiche en alternance. h Entrer le code 72 pour avoir accès au niveau "Paramétrage" au moyen des touches Plus on maintient la touche enfoncée, plus la valeur défile vite. h Valider avec Le nom du paramètre et la valeur s’affichent en alternance, par ex.
Régulateur Paramètre Plage des valeurs de...d’usine...à Consigne SP.L à 0.0 à SP.H Régulera sur cette valeur (valeur de la température, courant ou tension). Hystérésis 0.2 à 1.0 à 99.9 Froid T/°C SP = 70 °C 69 °C 9 SP = 8 °C Chaud T/°C HYS HYS t Relais excité t Relais excité Désexcité désexcité t t Limite inférieure de la consigne SP peut être réglé jusqu’à cette limite inférieure. -999 à -50 à +999 Limite supérieure de la consigne SP peut être réglé jusqu’à cette limite supérieure.
Paramètre Plage des valeurs de...d’usine...à Signification Enclenchement retardé après mise sous tension Pour la mise sous tension différée de plusieurs unités de l’installation. 0 à 60min En cas de défectuosité de la sonde le relais est immédiatement commandé, comme réglé dans Paramètre S.Er. Alarme -999 à -200 à +999 Limite inférieure de la température de l’alarme Dès que la valeur réelle passe sous cette limite pendant le mode chaud ou froid un message d’erreur s’affiche voir chap.
Paramètre Signification Plage des valeurs de...d’usine...
Paramètre Signification Plage des valeurs de...d’usine...à Résistance de tarage de ligne 0,0 à 0,0 à 99,9 en Ω Cette valeur sert à compenser la résistance de la ligne du capteur et dépend de la longueur de la ligne. Pour mesurer la température du mieux possible, il faut saisir ici la résistance ohmique de la ligne du capteur lorsque celui-ci a court-circuité.
Paramètre Signification Plage des valeurs de...d’usine...à H Revenir au premier paramètre SP du niveau "Paramétrage" au moyen de > 3 secondes. 4 Mise en service de l’appareil 0,1 à 0,8 à 99,9 s Constante de temps du filtre Pour adapter le filtre d’entrée numérique. En cas de perturbation du signal (parasites,...), 63% des modifications sont enregistrés après la constante du filtre. Les valeurs comprises entre 0,1 et 0,7 sont interprétées comme étant 0,8 (temps de scrutation).
4.3 Attribution du code d’accès (niveau "Déverrouillage") Le réglage au niveau "Déverrouillage" définit les droits d’accès qui déterminent si un paramètre s’affiche ou non au niveau "Utilisateur" et s’il peut être édité. enfoncée pendant 3 secondes et s’affiche. h Saisir le code 82 pour accéder au niveau "Déverrouillage" à l’aide des touches h Valider avec Paramètre et Droits d’accès clignotent en alternance, par ex. h Régler au moyen des touches et un droit d’accès Droit d’accès et . .
Commande Afficher la version software P Modifier la consigne et les autres Affichage de la température paramètres + (Exemple) Température modifiée P Afficher les autres paramètres (suivant droit d’accès réglé au niveau “Déverrouillage”) 5 Commande P ou Timeout (après 30 secondes env.
6 Caractéristiques techniques Entrée Désignation KTY2X-6 (PTC) -200 à +600°C Précision1/ Influence de la température ambiante Détection de ...
Entrée Désignation Etendue de mesure Précision1/ Influence de la température ambiante Détection de ... court-circuit de sonde rupture de sonde Courant 0 à 20 mA 0,1%/ ≤100ppm/K 3 non -2 à 22 mA mise à l’échelle avec et ou tableau spécifique client 4 à 20 mA 2,4 à 21,6 mA mise à l’échelle avec et 0,1%/ ≤100ppm/K 3 oui non oui Résistance d’entrée RE ≤ 3Ω Tension 0 à 10 V 0,1%/ ≤100ppm/K -1 à 11 V mise à l’échelle avec et ou tableau spécifique client Résistance d’entrée RE ≥ 100kΩ 1.
Influences de l’environnement 0 à +55°C pour montage côte-à-côte : 0 à +40°C Plage de température de stockage -40 à +70°C Résistance climatique ≤ 75% humidité relative sans condensation Sortie Relais K1 (contact inverseur) 150.000 coupures à 10A/250V AC 50Hz en charge ohmique 800.
Compatibilité électromagnétique Emission de parasites Résistance aux parasites Sécurité électrique EN 61326 Classe B Normes industrielles EN 61 010, partie 1, catégorie de surtension III, degré de pollution 2 Le logiciel et l’interface avec adaptateur sont en option et offrent les possibilités suivantes : - paramétrage et archivage simples et aisés par PC - duplication simple des paramètres pour appareils de type identique - possibilité de saisir un tableau de linéarisation Conditions logicielles et
7 Messages d’erreur Les messages d’erreur suivants restent affichés jusqu’à ce que la cause soit supprimée : Message d’erreur Cause Dépassement sup. de capacité d’affichage La valeur est trop grande et se situe en dehors de l’étendue de mesure. Dépassement inf. de capacité d’affichage La valeur est trop petite et se situe en dehors de l’étendue de mesure. Temps pour Enclenchement retardé après mise sous tension s’écoule. En cas de dépassement inf. /sup.
JUMO GmbH & Co. KG JUMO Régulation S.A. Adresse : Moltkestraße 13 - 31 36039 Fulda, Allemagne Adresse de livraison : Mackenrodtstraße 14 36039 Fulda, Allemagne Adresse postale : 36035 Fulda, Allemagne Téléphone : +49 661 6003-0 Télécopieur : +49 661 6003-607 E-Mail : mail@jumo.net Internet : www.jumo.net Actipôle Borny 7 rue des Drapiers B.P. 45200 57075 Metz - Cedex 3, France Téléphone : +33 3 87 37 53 00 Télécopieur : +33 3 87 37 89 00 E-Mail : info@jumo.net Internet : www.jumo.fr JUMO AUTOMATION S.P.