WARNING YJ USA Corp., 3970 Lindbergh Drive Adison, TX 75001 www.jumppod.
3
1. The owner and supervisors of the trampoline are responsible to make sure all the users are aware of practices specified in this manual. 2. Trained Spotter supervision is recommended. 3. Place the trampoline and trampoline enclosure on a level surface before use. 4. Must place the trampoline on lawn, bark wood chip, sand or cushioning materials. 5. Adequate overhead clearance is essential. A minimum of 7.3 m (24 ft) from ground level is recommended.
25. Do not attach anything to the barrier that is not a manufacturer approved accessory or part of the enclosure system. 26. Wear clothing free of drawstrings, hooks, loops, or anything that could get caught in the barrier. 27. Enter and exit the trampoline enclosure only at the door designed for that purpose. 28. Do not attempt to crawl under the barrier. 35. While keeping the head erect, focus eyes on the trampoline toward the perimeter. This will help control bounce. 36.
Note: The 6
the sharply spot.
1. Make sure you understand the information in the box at the top of this page before you begin assembling the trampoline. 1 Lay three Top Tubes (1), (2) and (3) on the ground as shown. Make sure there is a T-connector(4) on Top Tube (1, A marking with bigger end), Socket(7) on the Top Tube(2, B marking with bigger end) and T-connector(4) on the Top Tube(3, c marking with bigger end). Center 12 6 12 5 Insert Top Tube(1, A marking with small end) into Socket(7).
3. Lay the Bed (8) on the ground inside of the assembled frame. Make sure that the two warning decals (not shown) are on top of the Bed. 8 Frame V-rings Note: There are V-rings around the edge of the 10 10 Bed (8) and holes around the top of the frame. During this step, you will attach the Bed to the frame using the included Springs (10) for holes on top of frame and for holes on bottom of frame (see the inset drawing).
4 4. Lay the Frame Pad (9) on the frame. Double D-rings on the middle of pad should be fixed exactly on the right of each T-connector of frame. Do not use the trampoline without the Frame Pad (9), which is designed to reduce the likelihood of injury to the user from coming in contact with the trampoline frame. If you do not have a Frame Pad, call our Customer Hot Line toll-free at 877-927-8777, Monday-Friday,8 a.m. -5 p.m. Central Time.
6 6. Using the included plastic tie, attach the Safety Placard (11) to the frame near the point where jumpers will climb onto and off the trampoline. The trampoline is now fully assembled. Make sure that all parts are securely attached. Familiarize yourself and all users of the trampoline with the safety precautions, use and instructional materials, and care and maintenance instructions in this manual before using the trampoline. Frame 7.
10. Attach the other three Pole(16,17) in the same way. See inset drawing. 10 11. Lay out Top G3 Pole (18), joint each section Connector to a straight line as shown. Assemble the remaining Top G3 Pole (18) in the same way. Spread the Netting (20) on the trampoline bed, insert a Top G3 Pole (18) into the opening of Top Sleeve on the Netting (20). Insert the other Top G3 Pole (18) into the opposite opening of Top Sleeve on the Netting (20).
13. Note: During steps 14 and 15, you will “sew”the lower edge of the Netting(20) to the V-rings on the bed using the Cords(25). Locate the V-ring closest to the door. Thread one end of a Cord(25)through the lower edge of the Netting(20)above the V-ring and then thread the Cord through the V-ring. Tie the Netting to the V-ring, by making a double knot in the Cord. 14.
6WDNH It is possible for the trampoline/enclosure be blown about by high wind. If you anticipate high winds, the trampoline/enclosure should be moved to a sheltered location, disassembled, or tied down to the ground with ropes and stakes (not included). At least three ropes and three stakes should be used. The tops of the stakes should be at ground level so that they will not create a tripping hazard.
19 17 20 12 16 8 9 10 24 10 4 13 1 2 7 3 12 5 15 23 11 14 6 18(BLACK) 10 11 22 21 1 2 3 4 5 6 7 8 9 10 11 12 13 14 4 4 4 8 8 4 4 1 1 60 1 12 16 8 Top Tube(With T-connector, A marking) Top Tube(With Socket, B marking) Top Tube(With T-connector, C marking) T-Connector Leg Extension Center Socket Stitched Bed with V-ring Frame Pad Springs User’s Manual and safety Placard (2 pcs) Self-tapping screw Locknut U-bolt Bracket 15 16 17 18 19 8 4 4 2 4 20 21 22 23 24 25 1 8 1 4 16