M120 Internet Router PIC Guide Juniper Networks, Inc. 1194 North Mathilda Avenue Sunnyvale, California 94089 USA 408-745-2000 www.juniper.
M120 Internet Router PIC Guide This guide provides an overview and description of the Physical Interface Cards (PICs) supported by the Juniper Networks M120 Internet router. The PICs are described alphabetically. Table 1 on page 3 lists the PICs supported by the M120 Internet router by PIC family. PICs provide the physical connection to various network media types. The PICs are mounted on Flexible PIC Concentrators (FPCs), which are inserted into a slot in a router.
Table 1: PICs Supported by the M120 Internet Router Ports First JUNOS Support Page ATM2 DS3 IQ 4 8.0R2 20 ATM2 E3 IQ 4 8.0R2 22 ATM2 OC3/STM1 IQ 2 8.0R2 24 ATM2 OC12/STM4 IQ 1 8.0R2 27 ATM2 OC12/STM4 IQ 2 8.0R2 27 ATM2 OC48/STM16 IQ with SFP 1 8.0R2 30 Channelized DS3 IQ 4 8.0R2 33 Channelized E1 IQ 10 8.0R2 35 Channelized OC3 IQ 1 8.0R2 37 Channelized OC12 IQ 1 8.0R2 40 Channelized STM1 IQ 1 8.0R2 43 Channelized T1 IQ 10 8.0R2 45 DS3 4 8.
M120 Internet Router PIC Guide Table 1: PICs Supported by the M120 Internet Router (continued) Ports First JUNOS Support Page 10-Gigabit Ethernet DWDM 1 8.0R2 78 Gigabit Ethernet with SFP 1 8.0R2 60 Gigabit Ethernet with SFP 2 8.0R2 60 Gigabit Ethernet with SFP 4 8.0R2 60 Gigabit Ethernet with SFP 10 8.0R2 60 Gigabit Ethernet IQ with SFP 1 8.0R2 63 Gigabit Ethernet IQ with SFP 2 8.0R2 63 Gigabit Ethernet IQ2 with SFP 4 8.0R2 66 Gigabit Ethernet IQ2 with SFP 8 8.
Table 1: PICs Supported by the M120 Internet Router (continued) Ports First JUNOS Support Page SONET/SDH OC12c/STM4 1 8.0R2 91 SONET/SDH OC12/STM4 (Multi-Rate) with SFP 1 8.4 94 SONET/SDH OC12/STM4 (Multi-Rate) with SFP 4 8.3 94 SONET/SDH OC48c/STM16 with SFP 4 8.0R2 99 SONET/SDH OC48 /STM16 (Multi-Rate) with SFP 1 8.3 103 SONET/SDH OC192c/STM64 PIC with XFP 1 8.
M120 Internet Router PIC Guide FPCs and cFPCs Supported M120 routers support the FPCs listed in Table 2 on page 6. Table 2: FPCs Supported by the M120 Router FPC Type FPC Name FPC Model Number Maximum Number of PICs Supported per FPC Maximum Throughput per FPC First JUNOS Release 1 FPC1 M120-FPC1 4 4 Gbps 8.0R2 2 FPC2 M120-FPC2 4 10 Gbps 8.0R2 3 FPC3 M120-FPC3 1 10 Gbps 8.0R2 A cFPC is a combination of a PIC and an FPC.
FPCs and cFPCs Supported Table 4: Optical Interface Support for 10-Gigabit Ethernet cFPC (continued) Parameter 10-GBASE-S 10-GBASE-L 10-GBASE-E 10-GBASE-Z Maximum distance 50/125 MMF cable, 2000 Mhz-Km: 984 feet/300 m 9/125 SMF cable: 6.2 miles/10 km 9/125 SMF cable: 24.8 miles/40 km: Distances greater than 30 km are considered to be engineered links. 9/125 SMF cable: 49.6 miles/80 km 50/125 MMF cable, 500 Mhz-Km: 269 feet/82 m 50/125 MMF cable, 400 Mhz-Km: 217 feet/66 m 62.
M120 Internet Router PIC Guide Table 5: Optical Interface Support for SONET/SDH OC192/STM64 cFPC (continued) Intermediate reach (IR) 2 Parameter Short reach (SR) 1 Maximum distance SMF cable: 6.21 miles/10 km SMF cable: 24.8 miles/40 km; distances greater than 30 km are considered to be engineered links. SMF cable: 49.71 miles/80 km Transmitter wavelength 1290 through 1330 nm 1530 through 1565 nm 1530 through 1565 nm Average launch power –6 through –1 dBm –1.0.
PIC/FPC Compatibility PIC/FPC Compatibility Table 6 on page 9 provides a PIC/FPC compatibility matrix for the supported PICs for the M120 router. Table 6: M120 PIC/FPC Compatibility PIC Type Number of Ports PIC Model Number FPC1 FPC2 FPC3 ATM2 DS3 IQ 4 PB-4DS3-ATM2 8.0R2 – – ATM2 E3 IQ 4 PB-4E3-ATM2 8.0R2 – – 8.0R2 – – 8.0R2 – – – 8.
M120 Internet Router PIC Guide Table 6: M120 PIC/FPC Compatibility (continued) PIC Type Number of Ports PIC Model Number FPC1 FPC2 FPC3 2 PB-2EIA530 8.0R2 – – Fast Ethernet 4 PB-4FE-TX 8.0R2 – – Fast Ethernet 8 PB-8FE-FX 8.0R2 – – Fast Ethernet 12 PB-12FE-TX 8.0R2 – – Fast Ethernet 48 PB-48FE-TX – 8.0R2 – Gigabit Ethernet, SFP 1 PB-1GE-SFP 8.0R2 – – Gigabit Ethernet, SFP 2 PB-2GE-SFP – 8.0R2 – Gigabit Ethernet, SFP 4 PB-4GE-SFP – 8.
PIC/FPC Compatibility Table 6: M120 PIC/FPC Compatibility (continued) PIC Type Number of Ports PIC Model Number FPC1 FPC2 FPC3 NOTE: This PIC requires the 710-017980 version or later of the FPC1. 0 PB-MS-100-1 8.2R2 – – MultiServices 400 0 PB-MS-400-2 – 8.2 – MultiServices 500 0 PC-MS-500-3 – – 8.3 Tunnel Services 0 PB-TUNNEL-1 8.0R2 – – Tunnel Services 0 PB-TUNNEL – 8.0R2 – Tunnel Services 0 PC-TUNNEL – – 8.0R2 8.
M120 Internet Router PIC Guide Adaptive Services II PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features ■ Supports tunnel services. This feature is included with the PIC and does not require an individual license. ■ Individual licenses must be purchased for additional services. ■ Power requirement: 0.
Adaptive Services II PIC Table 7: Adaptive Services PICs Software Features Supported by the M120 Router Software Feature Adaptive Services II PIC Adaptive Services II Layer 2 Services PIC GRE Key – – GRE dont-fragment – – Stateful firewall with packet inspection: detects SYN attacks, ICMP and UDP floods, and ping-of-death attacks 8.0R2 – Network Address Translation (NAT) for IP addresses 8.0R2 – Port Address Translation (PAT) for port numbers 8.0R2 – IP Security (IPSec) encryption 8.
M120 Internet Router PIC Guide Table 7: Adaptive Services PICs Software Features Supported by the M120 Router (continued) Encapsulations: 14 ■ ■ Multilink Frame Relay (MLFR) ■ Multilink Point-to-Point Protocol (MLPP) Adaptive Services II PIC 8.
Adaptive Services II FIPS PIC Adaptive Services II FIPS PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features ■ JUNOS-FIPS requires an Adaptive Services II FIPS PIC for external IPSec connections. See the Secure Configuration Guide for Common Criteria and JUNOS-FIPS for more information. ■ Supports tunnel services. This feature is included with the PIC and does not require an individual license.
M120 Internet Router PIC Guide Software features For a list of the software features available for services PICs, see the JUNOS Services Interfaces Configuration Guide.
Adaptive Services II Layer 2 Services PIC Adaptive Services II Layer 2 Services PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features ■ Supports Layer 2 Service package only. Tunnel services are included with the PIC. Other services require an individual license. ■ Power requirement: 0.
M120 Internet Router PIC Guide Table 8: Adaptive Services PICs Software Features Software Feature Adaptive Services II PIC Adaptive Services II Layer 2 Services PIC GRE Key – – GRE dont-fragment – – Stateful firewall with packet inspection: detects SYN attacks, ICMP and UDP floods, and ping-of-death attacks 8.0R2 – Network Address Translation (NAT) for IP addresses 8.0R2 – Port Address Translation (PAT) for port numbers 8.0R2 – IP Security (IPSec) encryption 8.
Adaptive Services II Layer 2 Services PIC Table 8: Adaptive Services PICs Software Features (continued) Encapsulations: ■ Multilink Frame Relay (MLFR) ■ Multilink Point-to-Point Protocol (MLPP) 8.
M120 Internet Router PIC Guide ATM2 DS3 IQ PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features ■ Four DS3 ports ■ Power requirement: 0.41 A @ 48 V (20.0 W) ■ Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface.
ATM2 DS3 IQ PIC Software features ■ Per-virtual circuit (VC) and per-virtual path (VP) traffic shaping ■ Unspecified bit rate (UBR) traffic shaping ■ Fine-grained variable bit rate (VBR) traffic shaping ■ Circuit cross-connect (CCC) ■ ATM Inverse Address Resolution Protocol (ARP), which enables routers to automatically learn the IP address of the router on the far end of an ATM permanent virtual circuit (PVC) ■ Simple Network Management Protocol (SNMP): ■ Cables and connectors LEDs Alarms,
M120 Internet Router PIC Guide ATM2 E3 IQ PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features ■ Four E3 ports ■ Power requirement: 0.
ATM2 E3 IQ PIC Software features ■ Per-virtual circuit (VC) and per-virtual path (VP) traffic shaping ■ Unspecified bit rate (UBR) traffic shaping ■ Fine-grained variable bit rate (VBR) traffic shaping ■ Circuit cross-connect (CCC) ■ ATM Inverse Address Resolution Protocol (ARP), which enables routers to automatically learn the IP address of the router on the far end of an ATM permanent virtual circuit (PVC) ■ Simple Network Management Protocol (SNMP): ■ Cables and connectors LEDs Alarms, e
M120 Internet Router PIC Guide ATM2 OC3/STM1 IQ PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features 24 ■ ■ Two OC3 ports ■ Power requirement: 0.41 A @ 48 V (20 W) ■ Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface ■ Conforms to ANSI T1.105-1991 and T1E1.
ATM2 OC3/STM1 IQ PIC Software features Cables and connectors LEDs ■ Circuit cross-connect (CCC) for leveraging ATM access networks ■ User-configurable virtual circuit (VC) and virtual path (VP) support ■ Support for idle cell or unassigned cell transmission ■ OAM fault management processes alarm indication signal (AIS), remote defect indicator (RDI) cells, and loop cells ■ Point-to-point and point-to-multipoint mode Layer 2 counters per VC and per VP ■ Local and remote loopback ■ ATM Invers
M120 Internet Router PIC Guide Table 9: Optical Interface Support for ATM2 OC3 IQ PICs (continued) Parameter Intermediate Reach (IR) Multimode Standard Telcordia GR-253 Multivendor agreement Maximum distance 9.3 miles/15 km 1.
ATM2 OC12/STM4 IQ PICs ATM2 OC12/STM4 IQ PICs Left: 1-port ATM2 OC12/STM4 IQ PIC; Right: 2-port ATM2 OC12/STM4 IQ PIC Software release ■ 1-port: JUNOS 8.0R2 and later (Type 1) ■ 2-port: JUNOS 8.0R2 and later (Type 2) NOTE: These PICs are not supported in JUNOS Release 8.1R1. Description Hardware features ■ One or two OC12 ports ■ Power requirement: ■ 1-port: 0.41 A @ 48 V (20 W) ■ 2-port: 0.
M120 Internet Router PIC Guide Software features Cables and connectors LEDs ■ Circuit cross-connect for leveraging ATM access networks ■ User-configurable virtual circuit (VC) and virtual path (VP) support ■ Support for idle cell or unassigned cell transmission ■ OAM fault management processes alarm indication signal (AIS), remote defect indication (RDI), and loop cells ■ Point-to-point and point-to-multipoint mode Layer 2 counters per VC and per VP ■ Local and remote loopback ■ ATM Inverse
ATM2 OC12/STM4 IQ PICs Table 10: Optical Interface Support for ATM2 OC12/STM4 IQ PICs (continued) Parameter Intermediate Reach (IR) Transceiver Multimode Transceiver Standard Telcordia GR-253 Multivendor agreement Maximum distance 9.3 miles/15 km 546.
M120 Internet Router PIC Guide ATM2 OC48/STM16 IQ PIC with SFP Software release ■ JUNOS 8.0R2 and later (Type 2) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features 30 ■ ■ One OC48 port ■ Power requirement: 0.41 A @ 48 V ( 20 W) ■ Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface. ■ Conforms to ANSI T1.105-1991 and T1E1.
ATM2 OC48/STM16 IQ PIC with SFP Software features ■ Multiprotocol Label Switching (MPLS) circuit cross-connect for leveraging ATM access networks ■ User-configurable virtual circuit (VC) and virtual path (VP) support ■ Support for idle cell or unassigned cell transmission ■ OAM fault management processes alarm indication signal (AIS), remote defect indicator (RDI), and loop cells ■ Point-to-point and point-to-multipoint mode Layer 2 counters per VC and per VP ■ Local and remote loopback ■ ATM
M120 Internet Router PIC Guide Table 11: Optical Interface Support for ATM2 IQ OC48 PICs (continued) 32 ■ PIC Type Single-Mode Intermediate Reach Standard Telcordia GR-253 Maximum distance 9.
Channelized DS3 IQ PIC Channelized DS3 IQ PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features ■ Four DS3 ports ■ Power requirement: 0.32 A @ 48 V (15.
M120 Internet Router PIC Guide Software features ■ Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection (RED), weighted random early detection (WRED) ■ Simple Network Management Protocol (SNMP): DS1 MIB, DS3 MIB ■ Dynamic, arbitrary channel configuration ■ Encapsulations: ■ High-Level Data Link Control (HDLC) ■ Frame Relay ■ Circuit cross-connect (CCC) ■ Translational cross-connect (TCC) ■ Point-to-Point Protocol (PPP) Cables and connectors ■ LEDs On
Channelized E1 IQ PIC Channelized E1 IQ PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features Software features ■ Ten E1 ports ■ Power requirement: 0.15 A @ 48 V (7.2 W) ■ Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface. ■ Channelization: E1, DS0 ■ Data service unit (DSU) functionality ■ Ports configurable as clear channel E1 interfaces with 2.
M120 Internet Router PIC Guide Cables and connectors ■ LEDs One bicolor per E1 port: Alarms, errors, and events Instrumentation (counters) 36 ■ 120-ohm RJ-48C ■ Off—Port not enabled ■ Green—Physical E1 link is up; individual subchannels can be down ■ Red—Physical E1 link is down ■ Alarm indication signal (AIS) ■ Loss of frame (LOF) ■ Out of frame (OOF) ■ Failed signal rate (FSR) ■ Layer 2 per-queue and per-channel packet and byte counters Channelized E1 IQ PIC
Channelized OC3 IQ PIC Channelized OC3 IQ PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features ■ One OC3 port ■ Power requirement: 0.39 A @ 48 V (8.6 W) ■ Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface.
M120 Internet Router PIC Guide Software features ■ Quality of Service (QoS) per channel: weighted round-Robin (WRR), random early drop (RED), weighted random early drop (WRED) ■ Simple Network Management Protocol (SNMP): OC3 MIB, DS3 MIB, T1 MIB ■ Dynamic, arbitrary channel configuration ■ Full Bit Error Rate Testing (BERT) ■ Encapsulations: ■ High-Level Data Link Control (HDLC) ■ Frame Relay ■ Circuit cross-connect (CCC) ■ Translational cross-connect (TCC) ■ Point-to-Point Protocol (PPP
Channelized OC3 IQ PIC Table 12: Optical Interface Support for Channelized OC3 IQ PICs (continued) PIC Type Intermediate Reach (IR) Average launch power –15 through –8 dBm Receiver saturation –8 dBm Receiver sensitivity –28 dBm Channelized OC3 IQ PIC ■ 39
M120 Internet Router PIC Guide Channelized OC12 IQ PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features 40 ■ ■ One OC12 port ■ Power requirement: 0.23 A @ 48 V (10.
Channelized OC12 IQ PIC Software features Cables and connectors LEDs Alarms, errors, and events Instrumentation (counters) ■ Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection (RED), weighted random early detection (WRED) ■ Simple Network Management Protocol (SNMP): OC3 MIB, DS3 MIB, T1 MIB ■ Dynamic, arbitrary channel configuration ■ Full bit error rate test (BERT) ■ Encapsulations: ■ High-Level Data Link Control (HDLC) ■ Frame Relay ■ Circuit cross
M120 Internet Router PIC Guide Table 13: Optical Interface Support for Channelized OC12 IQ PICs (continued) Parameter Intermediate Reach (IR) Standard Telcordia GR-253 Maximum distance 9.
Channelized STM1 IQ PIC Channelized STM1 IQ PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features Software features ■ One STM1 port ■ Power requirement: 0.39 A @ 48 V (18.
M120 Internet Router PIC Guide Alarms, errors, and events Instrumentation (counters) 44 ■ ■ Alarm indication signal (AIS-L, AIS-P) ■ Bit error rate signal degrade (BERR-SD), bit error rate signal fail (BERR-SF) ■ Bit interleaved parity errors B1, B2, B3 (CV-S, CV-L, CV-P) ■ Errored seconds (ES-S, ES-L, ES-P), far-end bit errors REI-L, REI-P (CV-LFE, CV-PFE), far-end errored seconds (ES-LFE, ES-PFE), far-end severely errored seconds (SES-LFE, SES-PFE), far-end unavailable seconds (UAS-LFE, UAS-PF
Channelized T1 IQ PIC Channelized T1 IQ PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description ■ Ten T1 ports ■ Power requirement: 0.15 A @ 48 V (7.2 W) ■ Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface.
M120 Internet Router PIC Guide Hardware features ■ Data service unit (DSU) and channel service unit (CSU) functionality ■ Ports configurable as clear channel T1 interfaces with 1.544-Mbps connectivity ■ Framing: Superframe (SF or D4) and Extended Superframe (ESF) ■ Supports B8ZS (bipolar 8-zero substitution) and AMI (alternate mark inversion) line coding ■ Local, remote, and payload loopback testing ■ ANSI T1.
Channelized T1 IQ PIC Alarms, errors, and events Instrumentation (counters) ■ Alarm indication signal (AIS) ■ Remote defect indication (RDI) ■ Loss of frame (LOF) ■ Loss of signal (LOS) ■ Bipolar violation (BPV) ■ Excessive zero (EXZ) ■ Line code violation (LCV) ■ Error seconds (ES) ■ Severely errored seconds (SES) ■ Severely errored frames (SEF) ■ Bit error event (BEE) ■ Layer 2 per-queue and per-channel packet and byte counters ■ 24–hour history or error counter updated at 15–m
M120 Internet Router PIC Guide DS3 PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features 48 ■ DS3 PIC ■ Four DS3 ports ■ Power requirement: 0.47 A @ 48 V (22.5 W) ■ Integrated DSU interoperability with leading DSU vendors ■ High-performance throughput on each port at speeds up to 44.
DS3 PIC Software features ■ DS3 functionality: ■ C-bit framing ■ B3ZS line encoding ■ DS3 diagnostics and loopback control ■ DS3 alarm and event counting and detection ■ Per-packet counts and byte counts ■ Local and remote loopback testing, as well as BERT testing per DS3 ■ DS3 far-end alarm and control (FEAC) channel support ■ Encapsulations: ■ High-Level Data Link Control (HDLC) ■ Frame Relay ■ Circuit cross-connect (CCC) ■ Point-to-Point Protocol (PPP) Cables and connectors ■
M120 Internet Router PIC Guide E1 PICs Left: E1 RJ-48 PIC; Right: E1 Coaxial PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: These PICs are not supported in JUNOS Release 8.1R1. Description Hardware features 50 ■ E1 PICs ■ Four E1 or coaxial ports ■ Power requirement: 0.08 A @ 48 V (3.74 W) ■ Two versions: ■ 4-port, 120-ohm, RJ-48 ■ 4-port, 75-ohm, coaxial ■ Onboard DSU functionality for E1 connectivity ■ High-performance throughput on each port at speeds up to 2.
E1 PICs Software features ■ Integrated support for G.703 unframed mode and G.704 framed mode with CRC; this feature is user-configurable NOTE: The G.704 implementation supports speeds slower than 2.048 Mbps; multiple channels within a single E1 interface are not supported.
M120 Internet Router PIC Guide E3 IQ PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features 52 ■ E3 IQ PIC ■ Four E3 ports ■ Power requirement: 0.38 A @ 48 V (18 W) ■ Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface ■ Clear-channel (34.368-Mbps) and subrate E3 ■ Unframed or ITU G.
E3 IQ PIC Software features ■ Quality of service (QoS) per port: weighted round-robin (WRR), random early detection (RED), weighted random early detection (WRED) ■ Simple Network Management Protocol (SNMP): E3 MIB, QoS MIB ■ Input policing and output shaping ■ Provider-side rate limiting ■ Full data link connection identifier (DLCI) range with sparse channel numbering ■ Per-DLCI queues with weighted deficit round-robin and strict priority ■ Encapsulations: ■ High-Level Data Link Control (HDL
M120 Internet Router PIC Guide EIA-530 PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features 54 ■ EIA-530 PIC ■ Two EIA-530, X.21 or V.35 serial ports ■ Power requirement: 0.07 A @ 48 V (3.
EIA-530 PIC Software features Cables and connectors LEDs ■ Supports four queues per port ■ Random early detection (RED) ■ Transmitter Signal Element Timing is looped from the timing received on the Transmitted Signal Element DCE. EIA-530 ports support the ability to invert the Transmit Data Element. The EIA-530 ports support the following rates: 2.048 Mbps ■ 2.341 Mbps ■ 2.731 Mbps ■ 3.277 Mbps ■ 4.09 Mbps ■ 5.461 Mbps ■ 8.192 Mbps ■ 16.384 Mbps ■ V.35 ports support up to 2.
M120 Internet Router PIC Guide Fast Ethernet PICs Left: 4-Port Fast Ethernet PIC; Right: 8-Port Fast Ethernet PIC Left: 12-Port Fast Ethernet PIC; Right: 48-Port Fast Ethernet PIC 56 ■ Fast Ethernet PICs
Fast Ethernet PICs VHDCI to RJ-21 Cable Software release ■ 4-port: JUNOS 8.0R2 and later (Type 1) ■ 8-port: JUNOS 8.0R2 and later (Type 1) ■ 12-port: JUNOS 8.0R2 and later (Type 1) ■ 48-port: JUNOS 8.0R2 and later (Type 2) NOTE: These PICs are not supported in JUNOS Release 8.1R1. Description Hardware features Software features ■ 4 100Base-TX ports ■ 8 100Base-FX ports ■ 12 100Base-TX ports ■ 48 100Base-TX ports ■ Power requirement: ■ 4-port: 0.14 A @ 48 V (6.8 W) ■ 8-port: 0.
M120 Internet Router PIC Guide Cables and connectors 4-port PIC: ■ Connector: Two-pair, Category 5 unshielded twisted-pair connectivity through an RJ-45 connector ■ Pinout: MDI noncrossover 8-port PIC: ■ Connector: MT-RJ female ■ FX optical interface—see Table 14 on page 59 12-port PIC: ■ Connector: One very High Density Connector Interface (VHDCI) to RJ-21 cable that connects to an RJ-45 patch panel 48-port PIC: ■ VHDCI to RJ-21 cables that connect to an RJ-45 patch panel ■ Four VHDCI connec
Fast Ethernet PICs 48-port PIC—does not have port LEDs. To check port status on a 48-port PIC, use the show interfaces fe-fpc/pic/port command. For more information about this command, see the JUNOS Network Interfaces Configuration Guide. Table 14: Optical Interface Support for Fast Ethernet PICs Parameter FX Interface for 8-Port Optical interface Multimode Maximum distance 62.5/125 MMF cable: 1.
M120 Internet Router PIC Guide Gigabit Ethernet PICs with SFP Left: 1-Port Gigabit Ethernet PIC; Right: 2-Port Gigabit Ethernet PIC Left: 4-Port Gigabit Ethernet PIC; Right: 10-Port Gigabit Ethernet PIC 60 ■ Gigabit Ethernet PICs with SFP
Gigabit Ethernet PICs with SFP Software release ■ 1-port: JUNOS 8.0R2 and later (Type 1) ■ 2-port: JUNOS 8.0R2 and later (Type 2) ■ 4-port: JUNOS 8.0R2 and later (Type 2) ■ 10-port: JUNOS 8.0R2 and later (Type 3) NOTE: These PICs are not supported in JUNOS Release 8.1R1. Description Hardware features Software features ■ One, two, four, or ten Gigabit Ethernet ports ■ Power requirement: ■ 1-port: 0.15 A @ 48 V (7.3 W) ■ 2-port: 0.25 A @ 48 V (11.9 W) ■ 4-port: 0.50 A @ 48 V (23.
M120 Internet Router PIC Guide LEDs Status LED, one bicolor: ■ Off—PIC is not enabled ■ Green—PIC is operating normally ■ Red—PIC has an error or failure Port LEDs, one pair per port: ■ Link—If green, the port is online; if there is no light, the port is down ■ Activity—If flashing green, the port is receiving data; if there is no light, the port might be on but is not receiving data Table 15: Optical Interface Support for Gigabit Ethernet PICs with SFP Parameter 1000Base-SX 1000Base-LX 1000B
Gigabit Ethernet IQ PICs with SFP Gigabit Ethernet IQ PICs with SFP Left: 1-port Gigabit Ethernet IQ PIC; Right: 2-port Gigabit Ethernet IQ PIC Software release ■ 1-port: JUNOS 8.0R2 and later (Type 1) ■ 2-port: JUNOS 8.0R2 and later (Type 2) NOTE: These PICs are not supported in JUNOS Release 8.1R1. Description Hardware features Software features ■ One or two Gigabit Ethernet ports ■ Power requirement: 0.
M120 Internet Router PIC Guide Cables and connectors ■ You can install any transceiver supported by the PIC. For information about installing and removing transceivers, see the PIC and Transceiver Installation Instructions.
Gigabit Ethernet IQ PICs with SFP Table 16: Optical Interface Support for Gigabit Ethernet IQ PICs with SFP (continued) Parameter 1000Base-SX 1000Base-LX 1000Base-LH Average receive power –17 through 0 dBm –19 through –3 dBm –20 through –3 dBm Receiver saturation 0 dBm –3 dBm –3 dBm Receiver sensitivity –17dBm –19 dBm –20 dBm Gigabit Ethernet IQ PICs with SFP ■ 65
M120 Internet Router PIC Guide Gigabit Ethernet IQ2 PICs with SFP Left: 4-port Gigabit Ethernet IQ2 PIC (Type 1); Right: 8-port Gigabit Ethernet IQ2 PIC (Type 2) 66 ■ Gigabit Ethernet IQ2 PICs with SFP
g002378 Gigabit Ethernet IQ2 PICs with SFP Center: 8-port Gigabit Ethernet IQ2 PIC (Type 3) Software release ■ 4-port: JUNOS 8.0R2 and later (Type 1) ■ 8-port: JUNOS 8.0R2 and later (Type 2) ■ 8-port: JUNOS 8.5 and later (Type 3) NOTE: These PICs are not supported in JUNOS Release 8.1R1. Description Hardware features ■ Four or eight Gigabit Ethernet ports ■ Power requirement: ■ ■ 4-port: 0.65 A @ 48 V (31W) ■ 8-port (Type 2): 0.89 A @ 48 V (42.5W) ■ 8-port (Type 3): 1.
M120 Internet Router PIC Guide Software features Cables and connectors ■ Intelligent handling of oversubscribed traffic for Type 1 and Type 2 PICs ■ Optical diagnostics and related alarms ■ Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection (RED), weighted random early detection (WRED) ■ Virtual Router Redundancy Protocol (VRRP) support ■ Hierarchical shaping ■ Fine-grained queuing and shaping per logical interface at both ingress and egress ■ 802.
Gigabit Ethernet IQ2 PICs with SFP Table 17: Optical Interface Support for Gigabit Ethernet IQ2 PICs with SFP Parameter 1000Base-SX 1000Base-LX 1000Base-LH Optical interface Multimode Single-mode Single-mode Transceiver type SFP SFP SFP Standard IEEE 802.3—1998 IEEE 802.3—1998 Multivendor agreement Maximum distance 62.5/125 MMF cable: 656 ft/200 m 9/125 SMF cable: 6.2 miles/10 km 9/125 SMF cable: 43.5 miles/70 km 50/125 MMF cable: 1640 ft/500 m 62.5/125 or 50/125 MMF cable: 1804.
M120 Internet Router PIC Guide 10-Gigabit Ethernet IQ2 PIC with XFP Software release Description Hardware features 70 ■ ■ JUNOS 8.2 and later (Type 3) ■ One 10-Gigabit Ethernet port ■ Power requirements: 1.2 A @48 V (56 W) ■ High-performance throughput ■ WAN-PHY mode at 9.953 Gbps ■ LAN-PHY mode at 10.
10-Gigabit Ethernet IQ2 PIC with XFP Software features Cables and connectors LEDs ■ Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection (RED), weighted random early detection (WRED) ■ Configurable WAN-PHY mode options: ■ loopback ■ mpls ■ path-trace ■ trigger ■ Virtual Router Redundancy Protocol (VRRP) support ■ Hierarchical shaping ■ Fine-grained queueing and shaping per logical interface at both ingress and egress ■ 802.
M120 Internet Router PIC Guide Table 18: Optical Interface for 10-Gigabit Ethernet IQ2 PICs Parameter 10-GBase-S 10-GBase-L 10-GBase-E 10-GBase-Z Transceiver model number XFP-10G-S XFP-10G-L-OC192-SR1 XFP-10G-E-OC192-IR2 XFP-10G-Z-OC192-LR2 Optical interface Multimode Single-mode Single-mode Single-mode Transceiver type XFP XFP XFP XFP Standard IEEE 802.3ae—2002 IEEE 802.3ae—2002 IEEE 802.
10-Gigabit Ethernet PIC with XENPAK 10-Gigabit Ethernet PIC with XENPAK Software release ■ 10-Gigabit Ethernet PIC with XENPAK: JUNOS 8.0R2 and later (Type 3) ■ XENPAK-OTN transceivers: JUNOS 9.0R2 and later NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features Software features ■ One 10-Gigabit Ethernet port ■ Power requirement: 0.55 A @ 48 V (26.
M120 Internet Router PIC Guide Cables and connectors LEDs ■ Duplex SC/PC connector (RX and TX) ■ Optical interface support—See Table 19 on page 74 and Table 20 on page 75 Status LED, one bicolor: ■ Off—PIC not enabled ■ Green—PIC is operating normally ■ Red—PIC has an error or failure Port LEDs, one pair: ■ Link—If green, the port is online; if there is no light, the port is down ■ RX—If flashing green, the port is receiving data; if there is no light, the port might be on but is not receivi
10-Gigabit Ethernet PIC with XENPAK Table 19: Optical Interface Support for 10-Gigabit Ethernet PICs with XENPAK (continued) Parameter Short Wavelength Serial (10GBase-SR), LAN Rate Long Wavelength Serial (10GBase-LR), LAN Rate Extra-Long Wavelength Serial (10GBase-ER), LAN Rate Extra-Long Wavelength Serial (10GBase-ZR), LAN Rate Average receive power –9.9 through –1.0 dBm –14.4 through 0.5 dBm –15.8 through –1.0 dBm –24.0 through –7.0 dBm Receiver saturation –1.0 dBm 0.5 dBm –1.
M120 Internet Router PIC Guide Table 20: Optical Interface Support for 10-Gigabit Ethernet PICs with XENPAK-OTNs (continued) Optical transmitter Optical receiver Optical performance ■ Transmitter type: Electro-absorption Modulated Laser (EML) ■ Modulation format: Non-retum-to-zero (NRZ) ■ Channel-plan wavelength range: 1551.72 through 1542.94 nm ■ Channel-plan frequency range: 193.2 through 194.
10-Gigabit Ethernet PIC with XENPAK Table 21: XENPAK-OTN Optical Signal-to-Noise Ratio (OSNR) Performance (continued) OSNR (dB/0.1 nm) OSNR (dB/0.
M120 Internet Router PIC Guide 10-Gigabit Ethernet DWDM PIC Software release ■ JUNOS 8.0R2 and later (Type 3) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features 78 ■ ■ One 10-Gigabit Ethernet port ■ Power requirement: 0.55 A @ 48 V (26.
10-Gigabit Ethernet DWDM PIC Software features ■ Enhanced optical monitoring capabilities ■ CLI configurable wavelength support ■ Virtual Router Redundancy Protocol (VRRP) support ■ 802.1q virtual LANs (VLANs) support ■ 802.
M120 Internet Router PIC Guide MultiServices PICs Left: MultiServices 100 PIC; Right: MultiServices 400 PIC Center: MultiServices 500 PIC Software release 80 ■ MultiServices PICs
MultiServices PICs ■ MultiServices 100: JUNOS 8.2R2 and later (Type 1) NOTE: This PIC requires the 710-017980 version of the FPC1. Description Hardware features Software features ■ MultiServices 400: JUNOS 8.2 and later (Type 2) ■ MultiServices 500: JUNOS 8.3 and later (Type 3) ■ Supports tunnel services. This feature is included with the PIC and does not require an individual license. ■ Individual licenses must be purchased for additional services. ■ Power requirement: ■ ■ Type 1: 0.
M120 Internet Router PIC Guide Table 24: MultiServices PICs Software Features Supported on the M120 Router (continued) Stateful firewall with packet inspection: detects SYN attacks, ICMP and UDP floods, and ping-of-death attacks 8.2R2 8.2 8.3 Network Address Translation (NAT) for IP addresses 8.2R2 8.2 8.3 Port Address Translation (PAT) for port numbers 8.2R2 8.2 8.3 IP Security (IPSec) encryption 8.2R2 8.2 8.5 Active flow monitoring exports cflowd version 5 and version 8 records 8.2R2 8.
SONET/SDH OC3c/STM1 PIC SONET/SDH OC3c/STM1 PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: Although the illustration shows a multimode PIC, a multimode PIC and a single-mode intermediate reach PIC are both supported. NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features Software features ■ Four OC3 ports ■ Power requirement: 0.49 A @ 48 V (23.
M120 Internet Router PIC Guide Cables and connectors ■ Duplex SC/PC connector (Rx and Tx) ■ Optical interface support—See Table 25 on page 85 NOTE: To extend the life of the laser, when a PIC is not being actively used with any valid links, take the PIC offline until you are ready to establish a link to another device. For information about taking a PIC offline, see the request chassis pic offline command in the JUNOS System Basics and Services Command Reference.
SONET/SDH OC3c/STM1 PIC Alarms, errors, and events ■ ■ SONET alarms: ■ Alarm indication signal—line (AIS-L) ■ Alarm indication signal—path (AIS-P) ■ Bit error rate signal degrade (BERR-SD) ■ Bit error rate signal fail (BERR-SF) ■ Bit interleaved parity (BIP) error B1 ■ Bit interleaved parity (BIP) error B2 ■ Bit interleaved parity (BIP) error B3 ■ Loss of frame (LOF) ■ Loss of pointer (LOP-P) ■ Loss of signal (LOS) ■ Far-end bit error: remote error indication—line (REI-L) (CV-LFE)
M120 Internet Router PIC Guide Table 25: Optical Interface Support for SONET/SDH OC3c/STM1 PICs (continued) Parameter Intermediate Reach Multimode Standard Telcordia GR-253 Multivendor agreement Maximum distance SMF cable: 9.3 miles/15 km MMF cable: 1.
SONET/SDH OC3/STM1 (Multi-Rate) PICs with SFP SONET/SDH OC3/STM1 (Multi-Rate) PICs with SFP PORT 3 Left: SONET/SDH OC3/STM1 (Multi-Rate) PIC (Type 1); Right: SONET/SDH OC3/STM1 (Multi-Rate) PIC (Type 2) Software release Description Hardware features ■ 4-port: JUNOS 8.4 and later (Type 1) ■ 4-port: JUNOS 8.3 and later (Type 2) ■ Rate-selectable using one of the following rates: ■ 1-port OC12 ■ 1-port OC12c ■ 4-port OC3c ■ Power requirement: 0.
M120 Internet Router PIC Guide Software features Cables and connectors ■ Optical diagnostics and related alarms ■ Per-port SONET/SDH framing ■ Link aggregation ■ Alarm and event counting and detection ■ Dual-router automatic protection switching (APS) ■ Multiprotocol Label Switching (MPLS) fast reroute ■ Encapsulations: ■ High-Level Data Link Control (HDLC) ■ Frame Relay ■ Circuit cross-connect (CCC) ■ Translational cross-connect (TCC) ■ Point-to-Point Protocol (PPP) You can instal
SONET/SDH OC3/STM1 (Multi-Rate) PICs with SFP Alarms, errors, and events ■ ■ SONET alarms: ■ Alarm indication signal—line (AIS-L) ■ Alarm indication signal—path (AIS-P) ■ Bit error rate signal degrade (BERR-SD) ■ Bit error rate signal fail (BERR-SF) ■ Bit interleaved parity (BIP) error B1 ■ Bit interleaved parity (BIP) error B2 ■ Bit interleaved parity (BIP) error B3 ■ Loss of frame (LOF) ■ Loss of pointer (LOP-P) ■ Loss of signal (LOS) ■ Far-end bit error: remote error indication—l
M120 Internet Router PIC Guide Table 26: Optical Interface Support for SONET/SDH OC3/STM1 (Multi-Rate) PICs Configured at an OC3/STM1 Rate (continued) Parameter Multimode Intermediate Reach (IR-1) Long Reach (LR-1) Optical interface Multimode Single-mode Single-mode Transceiver type SFP SFP SFP Maximum distance MMF cable: 1.2 miles/2 km SMF cable: 9.3 miles/15 km SMF cable: 24.
SONET/SDH OC12c/STM4 PIC SONET/SDH OC12c/STM4 PIC Software release ■ JUNOS 8.0R2 and later NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features Software features Cables and connectors ■ One OC12 port ■ Power requirement: 0.23 A @ 48 V (10.
M120 Internet Router PIC Guide LEDs One tricolor per port: Alarms, errors, and events ■ Off—Not enabled ■ Green—Online with no alarms or failures ■ Amber—Online with alarms for remote failures ■ Red—Active with a local alarm; router has detected a failure ■ SONET alarms: ■ 92 ■ ■ Alarm indication signal—line (AIS-L) ■ Alarm indication signal—path (AIS-P) ■ Bit error rate signal degrade (BERR-SD) ■ Bit error rate signal fail (BERR-SF) ■ Bit interleaved parity (BIP) error B1 ■ Bit
SONET/SDH OC12c/STM4 PIC Table 28: Optical Interface Support for SONET/SDH OC12c/STM4 PICs Parameter Intermediate Reach Multimode Optical interface Single-mode Multimode Transceiver type Fixed Fixed Standard Telcordia GR-253 Multivendor agreement Maximum distance SMF cable: 9.3 miles/15 km MMF cable: 546.
M120 Internet Router PIC Guide SONET/SDH OC12/STM4 (Multi-Rate) PICs with SFP Left: 1-port SONET/SDH OC12/STM4 (Multi-Rate) PIC; Right: 4-port SONET/SDH OC12/STM4 (Multi-Rate) PIC Software release Description ■ 1-port: JUNOS 8.4 and later (Type 1) ■ 4-port: JUNOS 8.
SONET/SDH OC12/STM4 (Multi-Rate) PICs with SFP Software features Cables and connectors ■ Optical diagnostics and related alarms ■ Per-port SONET/SDH framing ■ Link aggregation ■ Alarm and event counting and detection ■ Dual-router automatic protection switching (APS) ■ Multiprotocol Label Switching (MPLS) fast reroute ■ Encapsulations: ■ High-Level Data Link Control (HDLC) ■ Frame Relay ■ Circuit cross-connect (CCC) ■ Translational cross-connect (TCC) ■ Point-to-Point Protocol (PPP)
M120 Internet Router PIC Guide Alarms, errors, and events ■ ■ SONET alarms: ■ Alarm indication signal—line (AIS-L) ■ Alarm indication signal—path (AIS-P) ■ Bit error rate signal degrade (BERR-SD) ■ Bit error rate signal fail (BERR-SF) ■ Bit interleaved parity (BIP) error B1 ■ Bit interleaved parity (BIP) error B2 ■ Bit interleaved parity (BIP) error B3 ■ Loss of frame (LOF) ■ Loss of pointer (LOP-P) ■ Loss of signal (LOS) ■ Far-end bit error: remote error indication—line (REI-L) (CV
SONET/SDH OC12/STM4 (Multi-Rate) PICs with SFP Table 29: Optical Interface Support for SONET/SDH OC12/STM4 (Multi-Rate) PICs Configured at an OC3/STM1 Rate (continued) Parameter Multimode Intermediate Reach (IR-1) Long Reach (LR-1) Optical interface Multimode Single-mode Single-mode Transceiver type SFP SFP SFP Maximum distance MMF cable: 1.2 miles/2 km SMF cable: 9.3 miles/15 km SMF cable: 24.
M120 Internet Router PIC Guide Table 31: Optical Interface Support for SONET/SDH OC12/STM4 (Multi-Rate) PICs Configured at an OC48/STM16 Rate (continued) Short Reach (SR-1) Intermediate Reach (IR-1) Long Reach (LR-2) Transceiver type SFP SFP SFP Maximum distance SMF cable: 1.24 miles/2 km SMF cable: 9.3 miles/15 km SMF cable: 49.
SONET/SDH OC48c/STM16 PIC with SFP SONET/SDH OC48c/STM16 PIC with SFP Software release ■ JUNOS 8.0R2 and later NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features Software features ■ Four OC48 ports ■ Power requirement: 0.86 A @ 48 V (41.
M120 Internet Router PIC Guide Cables and connectors You can install any transceiver supported by the PIC. For information about installing and removing transceivers, see the PIC and Transceiver Installation Instructions. ■ Duplex LC/PC connector (Rx and Tx) ■ Optical interface support—See Table 32 on page 101 NOTE: To extend the life of the laser, when a PIC is not being actively used with any valid links, take the PIC offline until you are ready to establish a link to another device.
SONET/SDH OC48c/STM16 PIC with SFP Alarms, errors, and events ■ ■ SONET alarms: ■ Alarm indication signal—line (AIS-L) ■ Alarm indication signal—path (AIS-P) ■ Bit error rate signal degrade (BERR-SD) ■ Bit error rate signal fail (BERR-SF) ■ Bit interleaved parity (BIP) error B1 ■ Bit interleaved parity (BIP) error B2 ■ Bit interleaved parity (BIP) error B3 ■ Loss of frame (LOF) ■ Loss of pointer (LOP-P) ■ Loss of signal (LOS) ■ Far-end bit error: remote error indication—line (REI-L)
M120 Internet Router PIC Guide Table 32: Optical Interface Support for SONET/SDH OC48c/STM16 PICs with SFP (continued) Parameter Short Reach (SR) Intermediate Reach (IR) Long Reach (LR) Maximum distance SMF cable: 1.24 miles/2 km SMF cable: 9.3 miles/15 km SMF cable: 49.71 miles/80 km Standard Telcordia GR-253 Telcordia GR-253 Telcordia GR-253—L-16.
SONET/SDH OC48/STM16 (Multi-Rate) PIC with SFP SONET/SDH OC48/STM16 (Multi-Rate) PIC with SFP Software release ■ JUNOS 8.3 and later (Type 2) Description ■ Rate-selectable using one of the following rates: Hardware features Software features ■ 1-port OC3c ■ 1-port OC12 ■ 1-port OC12c ■ 1-port OC48 ■ 1-port OC48c ■ Power requirement: 0.20 A @ 48 V (9.
M120 Internet Router PIC Guide Cables and connectors You can install any transceiver supported by the PIC. For information about installing and removing transceivers, see the PIC and Transceiver Installation Instructions.
SONET/SDH OC48/STM16 (Multi-Rate) PIC with SFP Alarms, errors, and events ■ ■ SONET alarms: ■ Alarm indication signal—line (AIS-L) ■ Alarm indication signal—path (AIS-P) ■ Bit error rate signal degrade (BERR-SD) ■ Bit error rate signal fail (BERR-SF) ■ Bit interleaved parity (BIP) error B1 ■ Bit interleaved parity (BIP) error B2 ■ Bit interleaved parity (BIP) error B3 ■ Loss of frame (LOF) ■ Loss of pointer (LOP-P) ■ Loss of signal (LOS) ■ Far-end bit error: remote error indication—
M120 Internet Router PIC Guide Table 33: Optical Interface Support for SONET/SDH OC48/STM16 (Multi-Rate) PICs Configured at an OC3/STM1 Rate (continued) Parameter Multimode Intermediate Reach (IR-1) Long Reach (LR-1) Optical interface Multimode Single-mode Single-mode Transceiver type SFP SFP SFP Maximum distance MMF cable: 1.2 miles/2 km SMF cable: 9.3 miles/15 km SMF cable: 24.
SONET/SDH OC48/STM16 (Multi-Rate) PIC with SFP Table 35: Optical Interface Support for SONET/SDH OC48/STM16 (Multi-Rate) PICs Configured at an OC48/STM16 Rate (continued) Parameter Short Reach (SR-1) Intermediate Reach (IR-1) Long Reach (LR-2) Transceiver type SFP SFP SFP Maximum distance SMF cable: 1.24 miles/2 km SMF cable: 9.3 miles/15 km SMF cable: 49.
M120 Internet Router PIC Guide SONET/SDH OC192c/STM64 PIC with XFP Software release ■ JUNOS 8.3 and later (Type 3) Description ■ One OC192 port ■ Power requirement: 0.
SONET/SDH OC192c/STM64 PIC with XFP Cables and connectors ■ Duplex LC connector (Rx and Tx) ■ Optical interface support—See Table 36 on page 110 NOTE: To extend the life of the laser, when a PIC is not being actively used with any valid links, take the PIC offline until you are ready to establish a link to another device. For information about taking a PIC offline, see the request chassis pic offline command in the JUNOS System Basics and Services Command Reference.
M120 Internet Router PIC Guide Alarms, errors, and events ■ ■ SONET alarms: ■ Alarm indication signal—line (AIS-L) ■ Alarm indication signal—path (AIS-P) ■ Bit error rate signal degrade (BERR-SD) ■ Bit error rate signal fail (BERR-SF) ■ Bit interleaved parity (BIP) error B1 ■ Bit interleaved parity (BIP) error B2 ■ Bit interleaved parity (BIP) error B3 ■ Loss of frame (LOF) ■ Loss of pointer (LOP-P) ■ Loss of signal (LOS) ■ Far-end bit error: remote error indication—line (REI-L) (CV
SONET/SDH OC192c/STM64 PIC with XFP Table 36: Optical Interface Support for SONET/SDH OC192 PICs (continued) Parameter Short reach (SR-1) Intermediate Reach (IR-2) Long Reach (LR-2) Transceiver type XFP XFP XFP Standard Telcordia GR-253 OC192 SR1 Telcordia GR-253 OC192 IR2 Telcordia GR-253 OC192 LR2 Maximum distance SMF cable: 6.21 miles/10 km SMF cable: 24.8 miles/40 km; distances greater than 30 km are considered to be engineered links. SMF cable: 49.
M120 Internet Router PIC Guide T1 PIC Software release ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description Hardware features Software features ■ Four T1 ports ■ Power requirement: 0.08 A @ 48 V (3.7 W) ■ Supports clear channel T1 per port (1.
T1 PIC Alarms, errors, and events ■ Alarm indication signal (AIS) ■ Bipolar violations ■ Excessive zeros ■ Far-end block errors (FEBE, E-bit errors) ■ Loss of frame (LOF), Loss of signal (LOS) ■ Yellow alarm bit (X-bit) disagreements T1 PIC ■ 113
M120 Internet Router PIC Guide Tunnel Services PIC Software release ■ JUNOS 8.0R2 and later (Type 1, Type 2, and Type 3) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Description ■ Power requirement: 0.07 A @ 48 V (3.
Appendix A High Availability Features High availability features include Routing Engine redundancy, graceful Routing Engine switchover (GRES), nonstop bridging, nonstop active routing, graceful restart for routing protocols, Virtual Router Redundancy Protocol (VRRP), and unified in-service software upgrade (ISSU). Some high availability features are not supported by all platforms and all PICs.
Copyright © 2008, Juniper Networks, Inc. All rights reserved. Juniper Networks, the Juniper Networks logo, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United States and other countries. JUNOS and JUNOSe are trademarks of Juniper Networks, Inc. All other trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies in this document.
