Terms and Conditions
Table Of Contents
- Table of Contents
- List of Figures
- List of Tables
- About This Topic Collection
- Part 1: Access Point Overview and Components
- Part 2: Planning for Access Point Installation
- Part 3: Safety Guidelines and Standards for Access Point Installation
- Part 4: Requirements and Certifications
- Part 5: Installing, Connecting, and Verifying the Access Point
- Chapter 7: Installing and Connecting the Access Point
- Installation Instructions Warning
- Unpacking a WLA532E Access Point
- Parts Inventory (Packing List) for a WLA532E Access Point
- Installing the WLA532E Access Point on a Ceiling Rail
- Installing the WLA532E Access Point Using the Plenum Bracket Kit
- Installing the WLA532E Access Point on a Ceiling Rail Using the Trapeze Legacy Mounting Bracket Adapter Kit
- Installing the WLA532E Access Point on the Wall Using the WLA-BRKT-WALL Wall-Mount Kit
- Installing the WLA532E Access Point on the Wall Using the WLA-GNGWLBX-ADP-EU Wall-Mount Kit
- Installing the WLA532E Access Point on the Wall Using the WLA-GNGWLBX-ADP-NA Wall-Mount Kit
- Connecting the Access Point to Wireless LAN Controllers
- Chapter 8: Verifying the Health of the Access Point
- Chapter 9: Customer Support
- Chapter 7: Installing and Connecting the Access Point
Environmental Requirements and Specifications for the WLA532E Access Point
The Wireless LAN Access Point WLA532E can be installed in a clean, dry,
temperature-controlled environment on a recessed, 9/16-inch or 15/16-inch T ceiling-tile
rail or on a wall using a country-specific mounting kit, and also inside the ceiling using a
metal plenum mounting bracket.
Table 8: WLA532E Environmental Tolerances
Environmental Tolerance
Access
Point StorageTransportationSeismicTemperature
Relative
humidityAltitude
Complies with
Environmental
Conditions and
Environmental
Tests for
Telecommunications
Equipment ETSI
EN 300 019-1-2
Class 2.3
Non- operating
storage ensured in
the temperature
range -40° F
through 158° F,
(-40° C through
70° C)
Complies with
Environmental
Conditions and
Environmental
Tests for
Telecommunications
Equipment ETSI
EN 300 019-1-2
Class 2.3
Non-operating
transportation
ensured in the
temperature
range -40° F
through 158° F,
(-40° C through
70° C)
Complies
with IEC
60068-2-6
requirements.
Normal
operation
ensured in the
temperature
range 32° F
through 122° F
(0° C through
50° C).
Normal
operation
ensured in
relative humidity
range of 5%
through 95%
(noncondensing)
No performance
degradation up
to 5,000 feet
(1524 meters)
IEC 60068-2-41
Combined
heat/low air
pressure
WLA532E
Related
Documentation
Site Preparation Checklist for the WLA532E Access Point on page 15•
• General Safety Guidelines and Warnings on page 23
• Medical Safety Compliance for WLA Series Access Points on page 25
Planning Guidelines for Using RingMaster to Plan a Mobility System
The Juniper Networks Mobility System is an enterprise wireless LAN (WLAN) solution
that seamlessly integrates with an existing wired enterprise network. The Mobility System
provides secure connectivity to both wireless and wired users in large environments such
as office buildings, hospitals, and university campuses.
If you are using RingMaster software to plan your Mobility System installation, we
recommend that you create and verify a network plan for the entire installation and
generate a wireless LAN access point (WLA) work order using RingMaster before installing
the access points. A network plan and the WLA work order generated from RingMaster
provide the following information about access point installation and configuration:
Copyright © 2012, Juniper Networks, Inc.18
WLA532E Access Point Hardware Documentation