Installation Guide

JUNO TYPE IC & TC RECESSED HOUSING INSTALLATION INSTRUCTIONS
3"
Step 1. Extend bar hangers to fit between joists. Bar hanger foot is contoured to easily align with bottom of joist (Fig. 3). Position fixture by hammering Real-Nails
TM
into joists
(Fig. 4). (Note: Bar hanger may be shortened to fit 12" framing or smaller by breaking at score lines). Step 2. Slide fixture along bar hangers into desired location. Use locking screws or slot to secure (Fig. 5). Step 3. Follow steps 1-4 under Electrical Connection. Step 4. When installing in drywall, cut appropriate sized hole.* After installing drywall, if necessary, adjust fixture for ceiling thickness by loosening hex screws that attach the round housing to the plaster frame. (Fig. 3) Relocating Fixture — Nail can be removed with hammer claw to allow easy repositioning of fixture without damaging bar hanger or nail (Fig. 6).
WARNING: For your safety, read and understand instructions completely before starting installation. Before wiring to power supply, turn off electricity at the fuse or circuit breaker box. NOTE: Juno recessed fixtures are designed to meet the latest NEC requirements and are listed in full compliance with UL1571, 1570 or 1598. Before attempting installation of any recessed lighting fixture, check your local electrical building code. This code sets the wiring standards and installation requirements for your locality and should be understood before starting work. Use of non-Juno trims voids Juno warranty.
Juno Type IC fixtures are designed for direct contact with insulating materials which are approved for this application (Fig. 2). Blinking light after installation indicates that improper bulb or trim is being used. Use Juno Air-Loc Gaskets or Air-Loc Rated Trims with Juno IC housings for additional energy savings and to comply with Washington State and other energy codes. *In Canada, when insulation is present, Type IC fixtures must be used.
Installation into Joist Construction
Installation into Suspended Ceiling
Figure 7
1300 South Wolf Road • Des Plaines, IL 60018 Phone [phone] • www.junolightinggroup.com
Electrical Connection Instructions
Step 1. Provide electrical service accord- ing to your local electrical code to the wiring box located on the plaster frame. Supply wire insulation must be rated for at least 90°C. Step 2. Remove wiring box cover. Remove the appropriate knock-out(s) to accommodate the type of electrical service to be used/allowed by your local electrical code (Fig. 9): Metal Conduit. Remove appropriate round knock-out(s) and connect conduit to wiring box with proper connectors (not supplied.) Non-Metallic Cable. Remove appropriate
knock-out(s) from top of wiring box and insert cable, pushing it past the cable grip. No other connector is required. Step 3. Standard J-Box: Connect supply wires to fixture wires with proper size wire nuts (not supplied), so as to cover all bare current-carrying conductors (Fig. 10). J-Box with Quick Connectors: Strip supply wire 3/8˝, insert each supply wire into appropriate junction box connector. Connect black fixture wire to hot, white fixture wire to neutral and green fixture wire to ground (Fig. 10). Step 4. Place all wiring and connections back in wiring box and replace cover.
Black
Lamp Socket
Thermal Protector
White
120V
Figure 10
Figure 9
Metal Conduit
Non- Metallic Cable
TYPE TC & PL for Non-Insulated Ceilings
Juno Type TC & PL fixtures are designed for installations where housing and J-Box will not come into contact with insulation. Insulation must be spaced 3" away from the housing and J-Box (Fig. 1)*. Blinking light after installation indicates that improper bulb or trim is being used or that fixture has been improperly covered with insulation.
TYPE IC for Insulated Ceilings
Figure 2
Figure 1
Step 1. Locate center of proposed opening on ceiling tile and cut appropriate sized hole.* Step 2. Place ceiling tile in T-bar grid. Step 3. Place fixture into position and snap bar hanger foot with integral T-bar clips onto T-bars (Fig. 7). Additional holes provided for securing with wire or screws as needed (Fig. 8). Step 4. Follow Steps 1-4 under Electrical Connection.
Figure 3
Trim Installation
Install trim using coil, leaf, torsion, or push-in springs as provided. Remove socket paint protector cover and install proper lamp as listed on housing label.
Figure 11
© 2010 Juno Lighting LLC Rev 2/10
Figure 5
Hex Screws
P5142
* Note: Cut a 4-1/2" (for 4" housings), 5-5/8" (for 5" housings) or 6
-
-7/8" (for 6" housings) opening. For sloped
ceiling housings, use the provided oval hole template.
Figure 4
Figure 6
Figure 8
Mark means lamp contains mercury. Follow disposal laws. See www.lamprecycle.org
Hg
Hg