Installation Guide

INSTALLATION INSTRUCTIONS
Installation
Step 1. Confirm the LED trim is compatible
with the recessed housing as outlined
previously in these instructions.
Step 2. Some recessed housings contain
an adjustable plate or bracket that supports
the socket. The socket may need to be
detached from the plate/bracket, and the
plate/bracket may need to be removed from
the housing prior to installation of the trim. For
detailed instructions on removing the plate or
bracket, refer to manufacturer’s installation
instructions.
Step 3. Installation into existing housings with
medium base sockets:
Screw the medium base socket adaptor into
the socket in the recessed housing. Plug the
connector provided on the trim to the mating
connector on the socket adaptor by pushing
firmly to ensure connectors are securely
fastened (Fig. 3).
Installation into dedicated quick connect
housings: Plug the connector provided on the
trim into the mating connector in the housing
by pushing firmly to ensure connectors are
securely fastened (Fig. 4).
Step 4. Insert trim torsion springs into
corresponding retaining brackets in recessed
housing. Carefully push trim towards ceiling
until the springs pull the trim tight.
Step 5. Turn power back on to fixture.
© 2012 Juno Lighting LLC Rev 7/12 P3435 pg 2 of 2
WARRANTY
Juno Lighting Group provides five year limited warranty on LED components from date of purchase. Juno Lighting Group’s obligation
is expressly limited to repair or replacement, without charge, at Juno Lighting Group’s factory after prior written return authorization has
been granted. This warranty shall not apply to products which have been altered or repaired outside of Juno Lighting Group’s factory. This
warranty is in lieu of all other warranties, expressed or implied, and without limiting the generality of the foregoing phrase, excludes any
implied warranty of merchantability. Also, there are no warranties which extend beyond the description of the product on the company’s
literature setting forth terms of sale.
Product Services Phone [phone]
1300 South Wolf Road • Des Plaines, IL 60018 • Phone [phone] • www.junolightinggroup.com
Medium Base
Socket Adapter
Quick Connect
Incandescent
Housing
Figure 4
Dedicated Quick
Connect Housing
Quick Connect
Recessed
Housing
Typical Spring
Retaining Bracket
Figure 2
WARNING: Trims must be
grounded as outlined below. Failure
to do so can result in electric shock
or undesired operation.
The recessed housing must contain
grounded brackets to support the trim
springs and provide electrical ground
to the trim (see Fig. 2). If the housing
is grounded but does not contain spring
retaining brackets, contact factory to order
an adapter kit (V6RL-TRB). To use this
product in an ungrounded housing, consult
factory for additional instructions.
Dedicated Quick Connect Housing
As standard, the primary connection means
provided on the Juno retrofit trims is a
connector that is designed to meet the
high efficiency requirements of California
T24-2008. The connector is only intended
to be plugged into the mating connector in
Juno housing part numbers IC23-LEDT24
and IC23R-LEDT24 or into the medium base
socket adaptor provided with the trim. Use of
this trim in any other quick connect housings
other than Juno or removing the factory
installed connector is not recommended and
voids the product warranty.
CAUTION: Power to the luminaire
must be turned off prior to installing
these LED trims. Failure to do so
can cause electric shock, which
can result in injury or death.
J6RLG3 Downlight Retrofit Inserts
The J6RLG3 downlight retrofit trim is
designed so that the decorative cone or
baffle inserts can be removed and replaced
in the field. To remove the factory installed
insert (Fig. 5):
1. Locate the quick release slot
on the back of the retrofit trim.
2. Insert a small, flat blade screwdriver into
the slot and push gently against the top of
the insert, releasing the insert from the
retrofit trim.
To re-install insert (Fig. 6):
1. Line up the insert with the aperture of the
retrofit trim.
2. With even force, push the insert into
the retrofit trim until the insert is fully
seated. Confirm that the insert is securely
fastened.
Figure 5
Quick
Release
Slot
For J6RLG3 and J6RLEG3 Retrofit Trim Series
600 Lumen, 900 Lumen and WarmDim™ (Patent pending)
Standard Version WarmDim Version
Figure 3
Figure 6
Retrofit Trim
Cone or
Baffle Insert