EN User Manual Dishwasher JGIN60315
CONTENTS Safety information Safety instructions Product description Control panel Programmes Settings 2 3 5 6 7 7 Before first use Daily use Hints and tips Care and cleaning Troubleshooting Technical information 9 10 12 13 15 18 Subject to change without notice. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages.
• • • • • • • • • • Do not change the specification of this appliance. The operating water pressure (minimum and maximum) must be between 0.5 (0.05) / 8 (0.8) bar (Mpa) Obey the maximum number of 13 place settings. If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position.
mains plug, use fuse: 13 amp ASTA (BS 1362). Water connection • Make sure not to cause damage to the water hoses. • Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage. • The water inlet hose has a safety valve and a sheath with an inner mains cable. • Do not drink and play with the water in the appliance.
PRODUCT DESCRIPTION 1 2 11 10 1 2 3 4 5 6 Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 9 8 7 6 5 4 7 8 9 10 11 Rinse aid dispenser Detergent dispenser Cutlery basket Lower basket Upper basket 3
CONTROL PANEL 1 2 6 1 2 3 4 On/off indicator Programme marker Indicators Delay button 3 5 4 5 Start button 6 Programme knob Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Drying phase. It comes on when the drying phase operates. End indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates.
PROGRAMMES Programme 2) 3) Degree of soil Type of load Programme phases Normal soil Crockery and cutlery • • • • Heavy soil Crockery, cutlery, pots and pans Normal soil Crockery and cutlery Consumption values 1) Duration (min) Energy (kWh) Water (l) Prewash Wash 50 °C Rinses Dry 195 1.039 11 • • • • Prewash Wash 70 °C Rinses Dry 150 170 1.5 - 1.6 13 - 15 • • • • Prewash Wash 65 °C Rinses Dry 120 130 1.3 - 1.
programme selection mode in the following way: Press and hold simultaneously Start and Delay until the appliance is in programme selection mode. The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales. The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water in your area.
indicators Start and on/off start to flash. 3. Press Delay. • The indicator starts to flash. • The indicators Start and on/off continues to flash. • The intermittent flashing of refers to the current set level, e.g. 5 flashes + pause + 5 flashes = level 5. 4. Press Delay again and again to change the setting. Each time you press Delay the level number increases. After level 10 you will start again from level 1. 5. Turn knob to on/off position to confirm the setting. BEFORE FIRST USE 1.
How to fill the rinse aid dispenser A D CAUTION! Only use rinse aid specifically designed for dishwashers. B C You can turn the selector of the released quantity (B) between position 1 (lowest quantity) and position 4 or 6 (highest quantity). B A 1. Press the release button (D) to open the lid (C). 2. Pour the rinse aid in the dispenser (A) until the liquid reaches the fill level 'max'. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid.
A 30 B Starting a programme with delay start D 20 C 1. Press the release button (B) to open the lid (C). 2. Put the detergent, in powder or tablets, in the compartment (A). 3. If the programme has a prewash phase, put a small quantity of detergent in the compartment (D). 4. Close the lid. Make sure that the release button locks into position. Using the multi-tablets When you use tablets, that contain salt and rinse aid, do not fill the salt container and the rinse aid dispenser. 1.
HINTS AND TIPS General The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • Remove larger residues of food from the dishes into the waste bin. • Do not pre-rinse dishes by hand. When needed, use the prewash programme (if available) or select a programme with a prewash phase. • Always use the whole space of the baskets.
Before starting a programme Unloading the baskets Make sure that: 1. Let the tableware cool down before you remove it from the appliance. Hot items can be easily damaged. 2. First remove items from the lower basket, then from the upper basket. • The filters are clean and correctly installed. • The cap of the salt container is tight. • The spray arms are not clogged. • There is dishwasher salt and rinse aid (unless you use multi- tablets). • The position of the items in the baskets is correct.
CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. External cleaning 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7.
TROUBLESHOOTING If the appliance does not start or it stops during operation, before you contact an Authorised Service Centre, check if you can solve the problem by yourself with the help of the information in the table. WARNING! Repairs not properly done may result in serious risk to the safety of the user. Any repairs must be performed by qualified personnel. With some problems the end indicator flashes intermittently indicating a malfunction.
Problem and alarm code Possible cause and solution The anti-flood device is on. • The end indicator flashes 3 times intermittently. • The Start indicator flashes continuously. • Close the water tap and contact an Authorised Service Centre. The appliance stops and starts more times during operation. • It is normal. It provides optimal cleaning results and energy savings. The program lasts too long. • If the delayed start option is set, cancel the delay setting or wait for the end of the countdown.
Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside a closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. • Plastic items may need to be towel dried. • We recommend to always use rinse aid, even in combination with multi-tablets. There are whitish streaks or bluish layers on glasses and dishes. • The release quantity of rinse aid is too much.
Problem Possible cause and solution Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. Refer to "Before first use", "Daily use" or "Hints and tips" for other possible causes.
100006621-A-232015