EN User Manual Dishwasher JGIN60315
CONTENTS Safety information Safety instructions Product description Control panel Programmes Settings 2 3 5 6 7 7 Before first use Daily use Hints and tips Care and cleaning Troubleshooting Technical information 9 10 11 13 14 16 Subject to change without notice. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages.
• • • • • • • • • • Do not change the specification of this appliance. The operating water pressure (minimum and maximum) must be between 0.5 (0.05) / 8 (0.8) bar (Mpa) Obey the maximum number of 13 place settings. If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position.
mains plug, use fuse: 13 amp ASTA (BS 1362). Water connection • Make sure not to cause damage to the water hoses. • Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage. • The water inlet hose has a safety valve and a sheath with an inner mains cable. • Do not drink and play with the water in the appliance.
PRODUCT DESCRIPTION 1 2 11 10 1 2 3 4 5 6 Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 9 8 7 6 5 4 7 8 9 10 11 Rinse aid dispenser Detergent dispenser Cutlery basket Lower basket Upper basket 3
CONTROL PANEL 1 2 6 1 2 3 4 On/off indicator Programme marker Indicators Delay button 3 5 4 5 Start button 6 Programme knob Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Drying phase. It comes on when the drying phase operates. End indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates.
PROGRAMMES Programme 2) 3) Degree of soil Type of load Programme phases Normal soil Crockery and cutlery • • • • Heavy soil Crockery, cutlery, pots and pans Normal soil Crockery and cutlery Consumption values 1) Duration (min) Energy (kWh) Water (l) Prewash Wash 50 °C Rinses Dry 195 1.039 11 • • • • Prewash Wash 70 °C Rinses Dry 140 160 1.3 - 1.5 13 - 15 • • • • Prewash Wash 65 °C Rinses Dry 100 120 1.2 - 1.
programme selection mode in the following way: Press and hold simultaneously Start and Delay until the appliance is in programme selection mode. The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales. The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water in your area.
BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets.
CAUTION! Only use rinse aid specifically designed for dishwashers. 1. Press the release button (D) to open the lid (C). 2. Pour the rinse aid in the dispenser (A) until the liquid reaches the fill level 'max'. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the release button locks into position. You can turn the selector of the released quantity (B) between position 1 (lowest quantity) and position 4 or 6 (highest quantity).
Setting and starting a programme close the door, the appliance continues from the point of interruption. Starting a programme Cancelling the delay start while the countdown operates 1. Open the water tap. 2. Close the appliance door. 3. Turn the knob until the programme marker is aligned with the programme you want to set. • On/off indicator comes on. • Start indicator starts to flash. 4. Press Start. • The programme starts and the indicator of the washing phase is on.
ECO programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. Using salt, rinse aid and detergent • Only use salt, rinse aid and detergent for dishwasher. Other products can cause damage to the appliance. • Multi-tablets are usually suitable in areas with a water hardness up to 21 °dH. In areas exceeding this limit, rinse aid and salt must be used in addition to the multi-tablets.
At the end of the programme water can still remain on the sides and on the door of the appliance. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spay arms decrease the washing results. Make a check regularly and, if necessary, clean them. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). Cleaning the filters The filter system is made of 3 parts. C 4. Wash the filters.
Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. External cleaning 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents.
Problem and alarm code Possible solution The programme does not start. • Make sure that the appliance door is closed. • Press Start. • If the delay start is set, cancel the setting or wait for the end of the countdown. • The appliance has started the procedure to recharge the resin inside the water softener. The duration of the procedure is approximately 5 minutes. The appliance does not fill with water. • The end indicator flashes 1 time intermittently. • The Start indicator flashes continuously.
Refer to "Hints and tips" for other possible causes. TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 596 / 818 - 898 / 575 Electrical connection 1) Voltage (V) 220 - 240 Frequency (Hz) 50 Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 13 Power consumption Left-on mode (W) 0.50 Power consumption Off-mode (W) 0.50 1) Refer to the rating plate for other values.
100006620-A-452014
