EN User Manual Dishwasher JGIN60618
CONTENTS Safety information Safety instructions Product description Control panel Programmes Settings Options 2 3 5 6 7 8 10 Before first use Daily use Hints and tips Care and cleaning Troubleshooting Technical information 11 12 14 16 17 21 Subject to change without notice. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions.
by clients in hotels, motels, bed & breakfast and other residential type environments. Do not change the specification of this appliance. The operating water pressure (minimum and maximum) must be between 0.5 (0.05) / 8 (0.8) bar (MPa) Obey the maximum number of 13 place settings. If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard.
• Do not use multi-plug adapters and extension cables. • Make sure not to cause damage to the mains plug and to the mains cable. Should the mains cable need to be replaced, this must be carried out by our Authorised Service Centre. • Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation. • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug.
PRODUCT DESCRIPTION 1 2 11 10 1 2 3 4 5 6 9 Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 8 7 6 5 4 7 8 9 10 11 Rinse aid dispenser Detergent dispenser Cutlery basket Lower basket Upper basket 3
CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Programs button Programme indicators Display Delay button 3 4 7 5 6 6 Start button 7 Indicators 8 Options button Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Drying phase. It comes on when the drying phase operates. XtraDry indicator. Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. HygienePlus indicator.
PROGRAMMES Programme 1) 2) 3) Degree of soil Type of load Programme phases Options • • Normal soil Crockery and cutlery • • • • Prewash Wash 50 °C Rinses Dry • • HygienePlus XtraDry • • Heavy soil Crockery, cut‐ lery, pots and pans • • • • Prewash Wash 70 °C Rinses Dry • • HygienePlus XtraDry • • Normal soil Crockery and cutlery • • • • Prewash Wash 65 °C Rinses Dry • • HygienePlus XtraDry • • Fresh soil Crockery and cutlery • • Wash 60 °C or 65 °C Rinses • • HygienePlus Xtra
Programme 1) Water (l) Energy (kWh) Duration (min) 5 0.1 14 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. Information for test institutes For all the necessary information for test performance, send an email to: Write down the product number (PNC) that is on the rating plate. info.test@dishwasher-production.
Water hardness German de‐ grees (°dH) French de‐ grees (°fH) mmol/l Clarke de‐ grees Water softener level 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
• The display shows the current setting. = rinse aid empty – notification activated. – = rinse aid empty notification deactivated. 2. Press Options to change the setting. 3. Press on/off to confirm the setting. AirDry AirDry improves the drying results with less energy consumption. AirDry is automatically activated with all programmes excluding . To improve the drying performance refer to the XtraDry option or activate AirDry.
least 10 minutes during the last rinsing phase. How to activate HygienePlus Press Options until the indicator is on. If the option is not applicable to the programme, the related indicator is off or it flashes quickly for a few seconds and then goes out. The display shows the updated programme duration. XtraDry Activate this option to boost the drying performance. With XtraDry on, the duration of some programmes, water consumption and the last rinse temperature can be affected.
B A M AX 4 4. Carefully shake the funnel by its handle to get the last granules inside. 5. Remove the salt around the opening of the salt container. 6. Turn the cap of the salt container clockwise to close the salt container. CAUTION! Water and salt can come out of the salt container when you fill it. After you fill the salt container, immediately start a programme to prevent corrosion. How to fill the rinse aid dispenser A D B C DAILY USE 1. Open the water tap.
2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start the correct programme for the type of load and the degree of soil.
Opening the door while the appliance operates Opening the door while a programme is running stops the appliance. It may affect the energy consumption and the programme duration. After closing the door, the appliance continues from the point of interruption. If the door is opened for more than 30 seconds during the drying phase, the running programme ends. It does not happen if the door is opened by AirDry function.
Using salt, rinse aid and detergent • Only use salt, rinse aid and detergent for dishwasher. Other products can cause damage to the appliance. • In areas with hard and very hard water we recommend to use plain dishwasher detergent (powder, gel, tablets containing no additional agents), rinse aid and salt separately for optimal cleaning and drying results. • At least once a month run the appliance with the use of appliance cleaner which is particularly suitable for this purpose.
CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. 3. Remove the flat filter (A). 4. Wash the filters. Cleaning the filters The filter system is made of 3 parts. C B A 1. Turn the filter (B) counterclockwise and remove it. 5.
• Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. Internal cleaning CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. • Carefully clean the appliance, including the rubber gasket of the door, with a soft damp cloth.
Problem and alarm code Possible cause and solution The program does not start. • • • • The appliance does not fill with water. • • • Make sure that the water tap is open. Make sure that the pressure of the water supply is not too low. For this information, contact your local water authori‐ ty. Make sure that the water tap is not clogged. Make sure that the filter in the inlet hose is not clogged. Make sure that the inlet hose has no kinks or bends.
Problem and alarm code Possible cause and solution The appliance trips the cir‐ cuit-beaker. • The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use. Internal electrical fault of the appliance. Contact an Au‐ thorised Service Centre. • Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes.
Problem Possible cause and solution The dishes are wet. • • • • • For the best drying performance activate the option Xtra‐ Dry and set AirDry . The programme does not have a drying phase or has a drying phase with low temperature. The rinse aid dispenser is empty. The quality of the rinse aid can be the cause. The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and use rinse aid and multi-tablets together.
Refer to "Before first use", "Daily use" or "Hints and tips" for other possible causes. TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 596 / 818 - 898 / 575 Electrical connection 1) Voltage (V) 220 - 240 Frequency (Hz) 50 Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 13 Power consumption Left-on mode (W) 5.0 Power consumption Off-mode (W) 0.
156919410-A-232017