EN User Manual Dishwasher JGVN 45515
CONTENTS Safety information Safety instructions Product description Control panel Programmes Settings Options 2 3 5 5 6 7 9 Before first use Daily use Hints and tips Care and cleaning Troubleshooting Technical information 10 11 12 14 15 17 Subject to change without notice. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages.
by clients in hotels, motels, bed & breakfast and other residential type environments. Do not change the specification of this appliance. The operating water pressure (minimum and maximum) must be between 0.5 (0.05) / 8 (0.8) bar (Mpa) Obey the maximum number of 9 place settings. If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard.
• Only for UK and Ireland. The appliance has a 13 amp mains plug. If it is necessary to change the fuse in the mains plug, use fuse: 13 amp ASTA (BS 1362). Water connection • Make sure not to cause damage to the water hoses. • Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage. • The water inlet hose has a safety valve and a sheath with an inner mains cable.
PRODUCT DESCRIPTION 1 2 11 10 1 2 3 4 5 6 9 Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 8 7 6 5 7 8 9 10 11 4 3 Rinse aid dispenser Detergent dispenser Cutlery basket Lower basket Upper basket CONTROL PANEL 1 1 On/off button 2 Programme buttons 3 Delay button 2 4 Indicators 3 4
Indicators Indicator Description End indicator. Multi-tab indicator. Salt indicator. It is always off while the programme operates.
Programme 1) Water (l) Energy (kWh) Duration (min) 8 0.8 30 4 0.1 14 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. Information for test institutes Write down the product number (PNC) that is on the rating plate. For all the necessary information for test performance, send an email to: info.test@dishwasher-production.
German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Factory setting. 2) Do not use salt at this level.
• The indicators and a go off. • The indicator continues to flash. • The end indicator indicates the current setting: End indicator on = rinse aid dispenser activated. 3. Press to change the setting. End indicator off = rinse aid dispenser deactivated. 4. Press the on/off button to confirm the setting. Acoustic signals Acoustic signals sound when a malfunction of the appliance occurs. It is not possible to deactivate these acoustic signals. 1.
BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets.
CAUTION! Only use rinse aid specifically designed for dishwashers. 4. Close the lid. Make sure that the release button locks into position. Fill the rinse aid dispenser when the indicator (E) becomes clear. 1. Press the release button (D) to open the lid (C). 2. Pour the rinse aid in the dispenser (A) until the liquid reaches the fill level 'max'. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam.
Starting a programme 1. Keep the appliance door ajar. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. 3. Press the button related to the programme you want to start. The related programme indicator comes on. 4. Close the appliance door to start the programme. Starting a programme with delay start 1. Set a programme. again and again until the 2. Press indicator related to the number of hours want to set comes on (3, 6 or 9).
''All in 1''). Follow the instructions written on the packaging. • Select the programme according to the type of load and degree of soil. With the ECO programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. Using salt, rinse aid and detergent • Only use salt, rinse aid and detergent for dishwasher. Other products can cause damage to the appliance. • Multi-tablets are usually suitable in areas with a water hardness up to 21 °dH.
Unloading the baskets 1. Let the tableware cool down before you remove it from the appliance. Hot items can be easily damaged. 2. First remove items from the lower basket, then from the upper basket. At the end of the programme water can still remain on the sides and on the door of the appliance. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spay arms decrease the washing results.
Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. External cleaning 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents.
Problem and alarm code Possible solution The programme does not start. • Make sure that the appliance door is closed. • If the delay start is set, cancel the setting or wait for the end of the countdown. • The appliance has started the procedure to recharge the resin inside the water softener. The duration of the procedure is approximately 5 minutes. The appliance does not fill with water. • The end indicator flashes 1 time intermittently. • Acoustic signal sounds 1 time intermittently.
Problem Possible solution The dishes are wet. • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty. • The quality of the rinse aid can be the cause. • The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and use rinse aid and multi-tablets together. Refer to "Hints and tips" for other possible causes.
100007060-A-502014