EN User Manual Dishwasher JGVN 45515
CONTENTS Safety information Safety instructions Product description Control panel Programmes Settings Options 2 3 5 5 6 7 9 Before first use Daily use Hints and tips Care and cleaning Troubleshooting Technical information 9 10 12 13 15 18 Subject to change without notice. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage.
by clients in hotels, motels, bed & breakfast and other residential type environments. Do not change the specification of this appliance. The operating water pressure (minimum and maximum) must be between 0.5 (0.05) / 8 (0.8) bar (MPa) Obey the maximum number of 9 place settings. If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard.
Make sure that there is access to the mains plug after the installation. • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • This appliance complies with the E.E.C. Directives. • Only for UK and Ireland. The appliance has a 13 amp mains plug. If it is necessary to change the fuse in the mains plug, use fuse: 13 amp ASTA (BS 1362). Water connection • Do not cause damage to the water hoses.
PRODUCT DESCRIPTION 1 2 11 9 10 1 2 3 4 5 6 Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 8 7 6 5 7 8 9 10 11 4 3 Rinse aid dispenser Detergent dispenser Cutlery basket Lower basket Upper basket CONTROL PANEL 1 1 On/off button 2 Programme buttons 3 Delay button 2 4 Indicators 3 4
Indicators Indicator Description End indicator. XtraDry indicator. Salt indicator. It is always off while the programme operates.
Programme 1) Water (l) Energy (kWh) Duration (min) 8 0.9 30 4 0.1 14 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. Information for test institutes Write down the product number (PNC) that is on the rating plate. For all the necessary information for test performance, send an email to: info.test@dishwasher-production.
German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Factory setting. 2) Do not use salt at this level. Whether you use a standard detergent or multi-tabs (with or without salt), set the proper water hardness level to keep the salt refill indicator active.
OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other. If you have selected non compatible options, the appliance will automatically deactivate one or more of them. Only the indicators of the options still active will stay on. option, the duration of some programmes, water consumption and the last rinse temperature can be affected.
CAUTION! Only use rinse aid specifically designed for dishwashers. 5. Turn the cap of the salt container clockwise to close the salt container. CAUTION! Water and salt can come out of the salt container when you fill it. After you fill the salt container, immediately start a programme to prevent corrosion. How to fill the rinse aid dispenser Fill the rinse aid dispenser when the indicator (E) becomes clear.
3. Load the baskets. 4. Add the detergent. 5. Set and start the correct programme for the type of load and the degree of soil. Using the detergent Starting a programme D A B 1. Keep the appliance door ajar. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. 3. Press the button related to the programme you want to start. The related programme indicator comes on. 4. Close the appliance door to start the programme.
Cancelling the delay start while the countdown operates When you cancel the delay start you have to set the programme and options again. Press and hold simultaneously and until the appliance is in programme selection mode. Cancelling the programme Press and hold simultaneously and until the appliance is in programme selection mode. Make sure that there is detergent in the detergent dispenser before you start a new programme. End of the programme When the programme is completed the indicator comes on.
1. Set the highest level of the water softener. 2. Make sure that the salt and rinse aid containers are full. 3. Start the shortest programme with a rinsing phase. Do not add detergent and do not load the baskets. 4. When the programme is completed, adjust the water softener according to the water hardness in your area. 5. Adjust the released quantity of rinse aid. 6. Activate the rinse aid empty notification. Loading the baskets • Only use the appliance to wash items that are dishwasher-safe.
1. Turn the filter (B) counterclockwise and remove it. 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 4. Wash the filters. CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. Cleaning the spray arms Do not remove the spray arms.
• If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance. To prevent this, we recommend to run long duration programmes at least 2 times per month. • To maintain the performance of your appliance at its best, we recommend to use monthly a specific cleaning product for dishwashers. Follow carefully the instructions on the packaging of the product.
Problem and alarm code Possible cause and solution The appliance does not drain the water. • The end indicator flashes 2 times intermittently. • Acoustic signal sounds 2 times intermittently. • Make sure that the sink spigot is not clogged. • Make sure that the drain hose has no kinks or bends. The anti-flood device is on. • The end indicator flashes 3 times intermittently. • Acoustic signal sounds 3 times intermittently. • Close the water tap and contact an Authorised Service Centre.
The washing and drying results are not satisfactory Problem Possible cause and solution Poor washing results. • Refer to "Daily use", "Hints and tips" and basket loading leaflet. • Use more intensive washing programmes. • Clean spray arm jets and filter. Refer to "Care and Cleaning". Poor drying results. • Tableware has been left for too long inside a closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level.
Problem Possible cause and solution There are residues of detergent in the dispenser at the end of the programme. • The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water. • Water cannot wash away the detergent from the dispenser. Make sure that the spray arm is not blocked or clogged. • Make sure that items in the baskets do not impede the lid of the detergent dispenser from opening. Odours inside the appliance. • Refer to "Internal cleaning".
Power consumption Off-mode (W) 0.10 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot water supply to decrease energy consumption. ENVIRONMENTAL CONCERNS dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office. Recycle the materials with the symbol .
156908441-A-482016