EN User Manual Dishwasher JGVN60415
CONTENTS Safety information Safety instructions Product description Control panel Programmes Settings Options 2 3 5 5 6 7 9 Before first use Daily use Hints and tips Care and cleaning Troubleshooting Technical information 10 11 13 14 16 19 Subject to change without notice. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages.
by clients in hotels, motels, bed & breakfast and other residential type environments. Do not change the specification of this appliance. The operating water pressure (minimum and maximum) must be between 0.5 (0.05) / 8 (0.8) bar (Mpa) Obey the maximum number of 13 place settings. If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard.
• This appliance complies with the E.E.C. Directives. • Only for UK and Ireland. The appliance has a 13 amp mains plug. If it is necessary to change the fuse in the mains plug, use fuse: 13 amp ASTA (BS 1362). Water connection • Make sure not to cause damage to the water hoses. • Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage.
PRODUCT DESCRIPTION 1 2 11 10 1 2 3 4 5 6 9 8 7 Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 6 5 4 7 8 9 10 11 Rinse aid dispenser Detergent dispenser Cutlery basket Lower basket Upper basket 3 CONTROL PANEL 1 1 On/off button 2 Programme buttons 3 Multitab button 2 3 4 Delay button 5 Indicators 4 5
Indicators Indicator Description End indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates.
Programme 1) Water (l) Energy (kWh) Duration (min) 9 0.8 30 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. Information for test institutes Write down the product number (PNC) that is on the rating plate. For all the necessary information for test performance, send an email to: info.test@dishwasher-production.
German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Factory setting. 2) Do not use salt at this level.
How to deactivate the rinse aid dispenser The appliance must be in programme selection mode. 1. To enter the user mode, press and hold simultaneously and until the indicators , and start to flash. 2. Press . • The indicators and a go off. continues to flash. • The indicator • The end indicator indicates the current setting: End indicator on = rinse aid dispenser activated. 3. Press to change the setting. End indicator off = rinse aid dispenser deactivated. The rinse aid indicator goes off. 4.
How to activate Multitab Press The related indicator comes on. . BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets.
How to fill the rinse aid dispenser A D CAUTION! Only use rinse aid specifically designed for dishwashers. B C You can turn the selector of the released quantity (B) between position 1 (lowest quantity) and position 4 or 6 (highest quantity). B A 1. Press the release button (D) to open the lid (C). 2. Pour the rinse aid in the dispenser (A) until the liquid reaches the fill level 'max'. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid.
A 30 B Starting a programme with delay start D 20 C 1. Press the release button (B) to open the lid (C). 2. Put the detergent, in powder or tablets, in the compartment (A). 3. If the programme has a prewash phase, put a small quantity of detergent in the compartment (D). 4. Close the lid. Make sure that the release button locks into position.
End of the programme When the programme is completed the indicator comes on. If you do not deactivate the appliance within 5 minutes all indicators goes off. This helps to decrease energy consumption. 1. To deactivate the appliance press the on/off button or wait for the Auto Off function to automatically deactivate the appliance. 2. Close the water tap. HINTS AND TIPS General The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment.
• Do not put in the appliance items made of wood, horn, aluminium, pewter and copper. • Do not put in the appliance items that can absorb water (sponges, household cloths). • Remove remaining food from the items. • Make soft the remaining burned food on the items. • Put hollow items (cups, glasses and pans) with the opening down. • Make sure that cutlery and dishes do not bond together. Mix spoons with other cutlery. • Make sure that glasses do not touch other glasses.
7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 4. Wash the filters. CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. External cleaning 5.
• If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance. To prevent this, we recommend to run long duration programmes at least 2 times per month. • To maintain the performance of your appliance at its best, we recommend to use monthly a specific cleaning product for dishwashers. Follow carefully the instructions on the packaging of the product.
Problem and alarm code Possible cause and solution The appliance does not drain the water. • The end indicator flashes 2 times intermittently. • Acoustic signal sounds 2 times intermittently. • Make sure that the sink spigot is not clogged. • Make sure that the drain hose has no kinks or bends. The anti-flood device is on. • The end indicator flashes 3 times intermittently. • Acoustic signal sounds 3 times intermittently. • Close the water tap and contact an Authorised Service Centre.
The washing and drying results are not satisfactory Problem Possible cause and solution Poor washing results. • Refer to "Daily use", "Hints and tips" and basket loading leaflet. • Use more intensive washing programmes. • If you use multi-tablets, always switch on the option Multitab. Poor drying results. • Tableware has been left for too long inside a closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level.
Problem Possible cause and solution Odours inside the appliance. • Refer to "Internal cleaning". Limescale deposits on the tableware, on the tub and on the inside of the door. • Refer to "The water softener". Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket.
100006661-A-232015
