JKG 5470 GEBRAUCHSANWEISUNG OPERATING INSTRUCTIONS 2222 046-13
WARNINGS It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings.
¥ Do not place carbonated or fizzy drinks in the freezer as it creates pressure on the container, which may cause it to explode, resulting in damage to the appliance. Installation ¥ During normal operation, the condenser and compressor at the back of the appliance heat up considerably. For safety reasons, minimum ventilation must be as shown in the relevant Figure. Attention: keep ventilation openings clear of obstruction.
USE Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. Operation Insert the plug into the wall socket. Open the refrigerator door and turn the thermostat knob, clockwise, beyond the ÇOÈ (STOP) position. The appliance will start to operate.
Movable shelves The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired. For better use of the space, the front half-shelves can lie over the rear ones. D338 Positioning the door shelves To permit storage of food packages of various sizes, the door shelves can be placed at different heights. To make these adjustments proceed as follows: Gradually pull the shelf in the direction of the arrows until it comes free, then reposition as required.
etc.) in the freezer compartment as they may burst. ¥ be sure that frozen foodstuffs are transferred from the foodstore to the freezer in the shortest possible time; Hints for storage of frozen food ¥ not open the door frequently or leave it open longer than absolutely necessary. To obtain the best performance from this appliance, you should: ¥ Once defrosted, food deteriorates rapidly and cannot be refrozen. ¥ ¥ Do not exceed the storage period indicated by the food manufacturer.
The freezer compartment, however, will become progressively covered with frost. This should be removed with the special plastic scraper provided, whenever the thickness of the frost exceeds 4 mm. During this operation it is not necessary to switch off the power supply or to remove the foodstuffs. However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out and it is advisable to carry out this operation when the appliance is empty.
auto-transformer must be used. ATTENTION! The appliance must be earthed. It must be possible to disconnect the appliance from the mains power supply; the plug must therefore be easily accessible after installation. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician.
2 min. 200 cm 50 mm Instructions for totally built-in appliances Building-in instructions Dimensions of housing min. cm 200 Height 1580 mm Depth 550 mm Width 560 mm 2 D567 For safety reasons, minimum ventilation must be as shown in Fig. 540 50 Attention: keep ventilation openings clear of obstruction.
If after having carried out the previously described operation there is still some space between the appliance and the kitchen unit, fit the trimming provided together with the appliance on the stop strip (A). Apply covers (B) on joint cover lugs and into hinge holes. A D265 B D726 B A Separate parts A, B, C, D as shown in the figure C D PR266 50mm Place guide (A) on the inside part of the furniture door, up and down as shown in the figure and mark the position of external holes.
Open the appliance door and the furniture door at 90¡. Insert the small square (B) into guide (A). Put together the appliance door and the furniture door and mark the holes as indicated in the figure. Remove the squares and drill holes with ¿ 2 mm at 8 mm from the outer edge of the door. Place the small square on the guide again and fix it with the screws supplied. 8mm A PR167 B Should the lining up of the furniture door be necessary, use the clearance of slots.