IMPRESSA Xs90 / Xs95 Instructions for use
Legend: DISPLAY: serves as information. DISPLAY: please follow the instructions shown.
Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 12 2 1 3 Fig. 9 Fig. 10 Fig. 11 Fig. 13 Fig. 14 Fig.
16 17 Description of the machine 18 15 14 19 13 12 11 10 9 8 7 20 21 22 23 24 3 25 27 6 5 4 26 2 1 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27.
Contents 1. Safety information ..............................................page 1.1 Warnings ................................................page 1.2 Precautions..............................................page 2. Before you start using the IMPRESSA ....................page 2.1 Checking the mains voltage ..........................page 2.2 Checking electrical fuse...............................page 2.3 Filling the water tank .................................page 2.4 Filling the bean tank..................
Before you begin Congratulations on having bought this IMPRESSA! In order to ensure perfect operation of your IMPRESSA, carefully read this operating manual and keep it for future reference. Should you need more information or meet with particular problems not specified in these operating instructions in sufficient detail, please contact JURA Elektroapparate AG directly or your local authorized dealer. You will also find useful tips on operation and maintenance of the machine on our website at www.jura.com.
2.3 Filling the water tank Only use fresh, cold water. Never fill the water tank with milk, mineral water or other liquids. Take out the water tank and thoroughly rinse it out with cold tap water. Then fill it with water and place it back into the coffee machine. Make sure the tank is installed correctly and that it engages properly. 2.
Place a receptacle under the 2-stage frothing jet (24) and press one of the Steam keys . The system now fills up automatically. A little water will leak from the frothing jet. SYSTEM FILLING HEATING UP PRESS RINSE Place a cup under the height-adjustable coffee spout (18). Press Rinse . MACHINE RINSING Now the water lines are flushed with fresh water. A little water will leak from the coffee spout (18).
Now turn the Rotary Switch (4) until the following message is displayed: EXIT Now press the Rotary Switch (4) to leave the programming mode. SELECT PRODUCT 5. Using a CLARIS plus filter cartridge When using the CLARIS plus filter cartridge correctly, decalcifying your IMPRESSA will no longer be necessary. For more information on the CLARIS plus filter cartridge refer to the brochure “CLARIS plus. Hard on limescale. Gentle on your coffee machine.” 5.
Fill the water tank (14) with cold, fresh tap water and place it back into the machine. Place a sufficiently large receptacle (min. 0.5 litres) under the pivoting steam spout (23) and press one of the Steam keys to start the filter rinsing process. FILTER RINSING Filter rinsing stops automatically. SELECT PRODUCT process (I.P.B.A.S.) moistens the coffee powder, briefly interrupts the flow of hot water and then begins with the actual brewing process.
1 ESPRESSO (example) POWDER The coffee brewing process stops automatically as soon as the set amount of water has run through. SELECT PRODUCT To stop the brewing process prematurely, press any of the product keys. We recommend always using powder from fresh coffee beans or pre-ground, vacuum-packed coffee. Never fill in more than 2 scoops of powder. The filler funnel is no storage tank. Make sure the coffee powder you use is not too fine.
To stop the process prematurely, turn the switch (22) back to . You can also change the amount of water set while the machine is brewing coffee. Open the programming door. Turn the Rotary Switch (4) until the display indicates the required amount (ML). The amount of water can be selected in increments of 5 ML. The amounts given in ML are approximate values and may vary from the effective quantity.
Dip the 2-stage frothing jet (24) into the milk and press the key. DRAW OFF STEAM When you have frothed the milk to your liking, pres the key again. 11.5 Cleaning the Professional-Cappuccino Frother and jet After heating or frothing milk, you should clean the Professional-Cappuccino Frother. We recommend cleaning it on a daily basis. 11.3 Attaching the Professional-Cappuccino Frother to the IMPRESSA Your IMPRESSA will not prompt you to clean the Professional-Cappuccino Frother.
MACHINE RINSING The coffee spout (18) is rinsed. 13. Programming The IMPRESSA leaves the factory with a number of default settings that allow you to make coffee without having to program the machine first. You can, however, adjust various parameters to make the coffee suit your personal taste.
SELECT PRODUCT Open the programming door (3). Press the Rotary Switch (4) until you hear an acoustic signal. FILTER NO or YES Turn the Rotary Switch (4) until the following message is displayed: POWDER QUANTITY Now press the Rotary Switch (4) to start programming. SELECT PRODUCT Then press a product key of your choice. NORMAL (example) – _ _ _ + Now turn the Rotary Switch (4) until the required amount of powder is set.
13.6 Programming the temperature for coffee, espresso and coffee à la carte You can adjust the temperature for each type of coffee separately. The temperature can be set to 2 different levels (NORMAL, HIGH). SELECT PRODUCT Open the programming door (3). Press the Rotary Switch (4) until you hear an acoustic signal. FILTER NO or YES Turn the Rotary Switch (4) until the following message is displayed: TEMPERATURE Now press the Rotary Switch (4) to start programming.
FILTER NO or YES Turn the Rotary Switch (4) until the following message is displayed: STEAM PORTION Press the Rotary Switch (4) to activate the program item. PORTION 20 SEC (example) Turn the Rotary Switch (4) to modify the steam portion and then confirm your setting by pressing the Rotary Switch (4). STEAM PORTION Turn the Rotary Switch (4) until the following message is displayed: EXIT Press the Rotary Switch (4) to leave the programming mode. SELECT PRODUCT 13.
Select this setting if you make mostly black coffees and are prepared to wait for approx. 1 minute before being able to draw steam. Economy mode 2 Selecting this level does not put the IMPRESSA in stand-by mode (economy temperature). The machine heats up each time you make coffee or need to draw steam. The IMPRESSA switches to economy temperature 5 minutes after you last used it. Select this setting if you make very few coffees (with or without milk) and are prepared to wait for approx.
Now press the Rotary Switch (4) to start programming. UNIT ON —:— Turn the Rotary Switch (4) to set the hours. UNIT ON 07:00 (example) Press the Rotary Switch (4) to confirm the hours and to activate the minutes. UNIT ON 07:00 Turn the Rotary Switch (4) to set the minutes. UNIT ON 07:15 (example) Press the Rotary Switch (4) to confirm the minutes.
LANGUAGE ENGLISH Turn the Rotary Switch (4) to set the language. LANGUAGE ENGLISH (example) Confirm your selection by pressing the Rotary Switch (4). LANGUAGE ENGLISH Now turn the Rotary Switch (4) until the following message is displayed: EXIT Now press the Rotary Switch (4) to leave the programming mode. SELECT PRODUCT 13.14 Programming the display This program item allows you to change the time format from 24 hrs. to AM/PM and the units from ml (millilitres) to oz (ounces).
Now press the Rotary Switch (4) to access the Information menu. TOTAL 1000 (example) Turn the Rotary Switch (4) to display how often you made espresso, 2 espressos, 1 coffee, 2 coffees, coffee à la carte, powder, water and steam. Finally, the number of cleaning and decalcifying cycles and filter changes are displayed. To exit the information program, press the Rotary Switch (4).
If this information is displayed, the machine will no longer make coffee. Refill water as described in Chapter 2.3. SELECT PRODUCT The water tank should be rinsed out and filled with fresh water daily. Always use fresh, cold water. Never fill the water tank with milk, mineral water or other liquids. 15.2 Emptying the coffee grounds TRAY MISSING Place the empty, clean drip tray (1) and the coffee grounds bin back into the IMPRESSA. SELECT PRODUCT 15.
Remove the screw in the bean tank (Fig. 9) and fold the finger protection device up (Fig. 10). Insert the key (Fig. 11). Now turn the key counter-clockwise until the jammed stone is released. Remove any remaining powder with a vacuum cleaner. Fold the finger protection device (Fig. 10) down and screw it tight. Fill the bean tank with fresh beans. 15.9 Prompt to decalcify 15.7 Changing the filter After a while the display will change. You should run the decalcifying cycle now (see Chapter 16).
15.11 General cleaning instructions Never use sharp objects or caustic chemicals for cleaning. Clean the case using a soft, damp cloth. Clean the pivoting steam spout (23) after each use. After heating milk, draw off some hot water to clean the inside of the pivoting steam spout (23). Remove the Professional-Cappuccino Frother to clean it thoroughly. The water tank should be rinsed out and filled with fresh water daily.
When the cleaning program has finished, take out the removable coffee powder tank and briefly rinse it under running water. You can also trigger a cleaning cycle manually at any point in time (see Chapter 13.3). 17. Decalcifying The IMPRESSA features an integrated decalcifying program. The process takes approx.50 minutes. Lime scale builds up in the IMPRESSA as a result of normal use. The degree of calcification depends on the hardness of the water you use.
You will hear an acoustic signal. EMPTY TRAY / EMPTY GROUNDS Empty out the drip tray (1) and the coffee grounds bin (Fig. 15). TRAY MISSING Place the empty, clean drip tray (1) and the coffee grounds bin back into the IMPRESSA. FILL WATER TANK / RINSE WATER TANK Thoroughly rinse out the water tank and fill it with fresh cold tap water. Then place it back into the IMPRESSA. PRESS STEAM Place a receptacle under the pivoting steam spout (23). Press one of the Steam keys .
20. Problems Problem Cause Remedy Grinding gear makes a very loud noise Foreign body in the grinding gear Please refer to Chapter 14.6 Too little froth when frothing milk Professional Cappuccino Frother clogged Clean frother (Chapter 11.
21. Legal information 22. Technical data These operating instructions contain all the information required for operating and maintaining the machine properly. Knowledge of and compliance with the specifications contained in these operating instructions is required for using the machine safely as well as for operational safety and safety during maintenance. These operating instructions cannot cover all conceivable applications.
Art. 67306 – 4/07 JURA Elektroapparate AG – Kaffeeweltstrasse 10 – CH-4626 Niederbuchsiten www.jura.
