IMPRESSA S90/S95/S9 IMPRESSA X90/X95 IMPRESSA 601 Art. Nr.
Jura Impressa S90/S95/S9 – X90/X95 – 601 English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 – 22 Legend: DISPLAY: serves as information. DISPLAY: please follow the instructions shown. = Note = Important = Tip Jura Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www.juraworld.
Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 6 Fig. 7 Fig. 9 Fig. 10 Fig. 5 Fig.
12 13 14 15 16 11 17 10 9 8 7 6 5 4 18 20 C F B G A H 21 22 23 1 E 19 3 2 D
Instructions for use 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Drip tray / residual water container Drip tray cover Cover for programming keys Coffee key for 2 large cups Coffee key for 1 large cup Coffee key for 2 small cups Coffee key for 1 small cup Key for special coffee ON/OFF switch Rinsing key Display dialogue system Water tank with carrying handle Cover for bean container and aroma protection lid Cover for pre-ground coffee filler funnel Height-adjustable coffee-spout Cup warming
13.1 13.2 13.3 13.4 13.5 13.6 13.7 13.8 13.9 13.10 Table of contents Jura Impressa 1. Description ......................................................page 2. Safety instructions ............................................page 2.1 Warnings ..................................................page 2.2 Safety precautions......................................page 3. Check before use ..............................................page 3.1 Checking mains voltage...............................page 3.
Important information for the user 2. Safety instructions Thank you for choosing this Jura product. 2.1 Warnings Please study these instructions carefully before using your new machine and keep them in a safe place for easy reference in the future.
If using acidic decalcifying agents be sure to immediately remove any splashes and drops from delicate surfaces, especially natural stone and wooden surfaces, or take corresponding precautions. 3. Check before use 3.1 Checking mains voltage The machine is set for the correct voltage before leaving our factory. Ensure that your mains voltage corresponds to the details quoted on the rating plate attached to the bottom of the machine. 3.2 Checking fuse The machine is designed for a current of 10 amps.
When you switch on the machine or press any key, the cup illumination is activated for 3 minutes. To switch on the cup illumination, with the machine switched off, press any key. HARDNESS LEVEL 3: HARDNESS LEVEL 4: German water hardness 16 – 23° French water hardness 28.64 – 41.14° German water hardness 24 – 30° French water hardness 42.96 – 53.7° 5. Rinsing the machine RINSE UNIT Place an empty cup under the coffee-spout (15). Press rinsing key .
Pull down cartridge mounting, until it engages audibly. Fill water tank with cold, fresh tap-water and replace it. Switch the machine on by pressing key ON/OFF. P Open front cover (3) and press key until you hear an acoustic signal. PRESS KEY / POWDER QUANTITY Press key + several times until the following message appears: FILTER NO By pressing key P you can hear an acoustic signal. NO flashes You can alter the setting by pressing key - or + .
8.1 Drawing off powder coffee Open cover (3) Press selector key for pre-ground powder coffee . FILL POWDER Now put 1 or 2 level measuring spoons of pre-ground coffee into the pre-ground powder funnel (14). Put 1, respectively 2 cups under the coffee-spout (15) and press the required key. Never use soluble instant coffee or quick coffee. Only use coffee powder from freshly ground beans or pre-ground vacuum-packed coffee. Never fill the funnel with more than 2 portions coffee powder at a time.
With the flow-adjustment you can set the optimum frothing. Turn the handle slightly to the right or to the left until you obtain the required result. 11.3 Drawing off hot milk using the Auto-Cappuccinatore S9 12. Switching off machine The Auto-Cappuccinatore of the S9 can be used to draw off hot milk. Adjust the selector lever (1) (Fig. 10) to position (3) to draw off hot milk. Install the Auto-Cappuccino. This is included in your Welcome Pack. 11.
.1 Programming powder quantity Switch the machine on by pressing ON/OFF key . Press key P until you can hear an acoustic signal. POWDER QUANTITY / SELECT KEY Now press the key that you want to programme. Use the key for 1 cup only. The corresponding quantity for 2 cups is adjusted automatically by the machine after programming is finished. POWDER - ·········· II ·········· + The powder quantity can be selected by pressing keys + or briefly.
The required portion of tea-water is programmed now. By pressing the + button, you can select the next phase, or press the N button in order to leave the programming. 13.6 Programming Filter Please read chapter 7.1 “Placing filter“. 13.7 Programming water hardness (only with setting Filter no) HARDNESS LEVEL 3 Press key P By pressing key + or - briefly you can programme the water hardness level. Then press key P briefly to store the water hardness level in memory.
13.10 Programming automatic switch on time A programming of the timer clock is necessary if an automatic switch on is needed. UNIT ON —.— Press key P . By briefly pressing key + or - you can set the hours and then confirm by pressing key P . By briefly pressing key + or - you can set the minutes and then confirm by pressing key P . By pressing the + button, you can select the next phase, or press the N button in order to leave the programming.
14.2 Empty grounds container Coffee grounds are collected in the grounds container. EMPTY GROUNDS If this message shows on the display no more coffee can be drawn off. It is necessary to empty the grounds container. Remove drip tray carefully as there is water in it. Do not disconnect the machine from power socket while you empty grounds. Remove any remaining beans with a vacuum cleaner. Put the spanner on (Fig.7). Now turn spanner anticlockwise until the foreign object loosens.
14.9 General cleaning instructions 15. Cleaning Never use abrasive articles or corrosive chemicals to clean your machine. Wipe down the casing inside and out using a soft, damp cloth. Clean the pivoting nozzle after every use. After warming milk, draw off some hot water to clean the pivoting nozzle inside. You can take off the Auto-cappuccino for a thorough cleaning. The water tank should be rinsed and filled with clean water daily. The machine has an integrated cleaning program.
Run the decalcifying program only after the machine has been switched off for at least 5 hours and has cooled down completely. The running decalcifying program must not be interrupted. If using acidic decalcifying agents be sure to immediately remove any splashes and drops from delicate surfaces, especially natural stone and wooden surfaces, or take corresponding precautions. In any case please wait until the filled decalcifying agent is used up and the tank is empty. Never top up the decalcifying agent.
17. Disposal For correct disposal, you should return your coffee machine to your dealer, Jura service centre or Jura Elektroapparate AG. 18. Tips for a perfect coffee Height adjustable coffee-spout You can adjust the height of the coffee-spout to the size of your cups. Grinding Please refer to chapter 3.4 “Adjusting grinder“. Pre-warm cups You should warm cups in advance with hot water or steam. The smaller the quantity of coffee, the more important warming the cups is.
19. Messages Cause Action FILL WATER Water tank is empty Water level indicator in tank is jammed Tank is calcified, water level indicator is stuck Top up with water Empty tank, rinse out, fill up and replace Remove tank, decalcify, rinse well, fill up with water and replace FILL BEANS Bean container is empty Message still displayed, although beans filled Top up with beans Draw off cup of coffee.
Cause Action You have drawn off coffee 220 times or run the rinsing program 180 times Message still displayed, although machine cleaned Clean as described in chapter 14 Run cleaning program again; this time do not add cleaning tablet UNIT CALCED The espresso/coffee machine sector needs decalcifying Message still displayed, although machine decalcified Run decalcifying program as described in chapter 15 Run cleaning program again; this time using water only and without decalcifying agent FAULT 2 Temp
Problem Cause Action Not enough froth while frothing up milk – Unsuitable milk-type – Frothing nozzle blocked – Clean Auto-Cappuccino – – – – Use full cream milk Clean frothing nozzle Clean Auto-Cappuccino as described in chapter 10.3 If the above mentioned problems and/or messages still persist, please contact your dealer or get in touch directly with Jura Elektroapparate AG. 21. Legal information 22.
