IMPRESSA X90/X95 Art. Nr.
Jura Impressa X90/X95 English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 – 22 Legend: DISPLAY: serves as information. DISPLAY: please follow the instructions shown. = Note = Important = Tip Jura Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www.juraworld.
Fig. 1 A Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 B Fig.
12 13 14 15 16 D E C F B G A H 11 10 9 8 7 6 5 4 17 18 19 20 21 22 3 23 2 1
Instructions for use 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21.
Table of contents 1. Description ........................................................page 2. Safety instructions ..............................................page 2.1 Warnings ...................................................page 2.2 Safety precautions ........................................page 3. Check before use.................................................page 3.1 Checking mains voltage..................................page 3.2 Checking fuse ..............................................
Important information for the user 2. Safety instructions Thank you for choosing this Jura product. 2.1 Warnings Please study these instructions carefully before using your new machine and keep them in a safe place for easy reference in the future.
If using acidic decalcifying agents be sure to immediately remove any splashes and drops from delicate surfaces, especially natural stone and wooden surfaces, or take corresponding precautions. 3. Check before use 3.1 Checking mains voltage The machine is set for the correct voltage before leaving our factory. Ensure that your mains voltage corresponds to the details quoted on the rating plate attached to the bottom of the machine. 3.2 Checking fuse The machine is designed for a current of 10 amps.
Place a container under the coffee-spout (15) and press rinsing key . UNIT RINSING COFFEE READY 4.2 Cup illumination The cup illumination puts your coffee in a good light, making it a treat for the eyes. When you switch on the machine or press any key, the cup illumination is activated for 3 minutes. To switch on the cup illumination, with the machine switched off, press any key. 5. Rinsing the machine RINSE UNIT Place an empty cup under the coffee-spout (15). Press rinsing key .
7. Use of Claris filter cartridges Under proper implementation of Claris filter cartridges, decalcifying of the machine becomes unnecessary. For further information, please read the brochure “Claris. Tough to calcium deposits, gentle to your coffee machine“. 7.1 Placing filter Pull up cartridge mounting. Pressing lightly, place the filter cartridge in the water tank (Fig. 2). Pull down cartridge mounting, until it engages audibly. Fill water tank with cold, fresh tap-water and replace it.
UNIT RINSING COFFEE READY Put 1, respectively 2 cups under the coffee-spout and press the required key. The pre-brew system (I.P.B.A.S.©) moistens the coffee powder, briefly interrupts the flow and then starts the real brewing process. 9. Drawing off hot water You can interrupt the flow of coffee at any time by simply pressing any of the coffee keys. Put a cup under the height-adjustable coffee spout (22) and turn selector switch for hot water (19) to the symbol .
Place a cup under the steam/frothing nozzle (20) and immerse the frothing aid in the milk to be frothed or the liquid to be heated. Press steam portion draw-off key . STEAM PORTION You can stop the draw-off operation at any time by pressing the steam draw-off key . COFFEE READY 11. Connecting the Profi-Auto-Cappuccino/ Caffè Latte to the X90/X95 Disassemble the replaceable hot water nozzle or the replaceable steam/frothing nozzle. Mount the Profi-Auto-Cappuccino/Caffè Latte (Fig. 10).
. Programming Before leaving our factory, the machine is adjusted to enable you to obtain coffee without any additional programming. In order to adapt the result to your personal taste, various settings can be programmed individually. The programming keys are located behind the front cover (3).
By pressing the + button, you can select the next phase, or press the N button in order to leave the programming. 13.4 Programming steam portion STEAM PORTION Press key P . PORTION /....20 SEC. By pressing key + or - you can programme time in seconds (drawing off time of 3 – 250 sec.) Press key P . STEAM PORTION By pressing the + button, you can select the next phase, or press the N button in order to leave the programming. 13.
ECONOMY MODE OFF means that the stand-by-status for steam is set to 20 minutes and the heating for the cup warming tray is on. After 10 minutes the warning lamp goes out. By pressing the steam key anew, the machine returns to stand-by-status for drawing off steam. To switch off the automatic timer proceed as follows: Press key P Press key N UNIT ON —:— 13.11 Programming automatic switch off time 13.
13.14 Program key N By using key N you can set back the following settings (powder quantity, coffee temperature, water quantity, steam portion, tea portion) to their original standard settings. COFFEE READY Press key N until you can hear an acoustic signal. If a mistake occurs while programming one of the above settings, just press key N and the chosen setting moves back to its original standard setting. 14. Care and maintenance 14.
14.6 Clean machine CLEAN UNIT After coffee, etc., has been drawn off 220 times or after 180 rinsing programs have been run, the machine must be cleaned. You can continue to draw off coffee and hot water / steam. However we recommend that you clean the machine (as described in chapter 15) within the next few days. CLEAN NOW An acoustic signal indicates the need of an immediate cleaning. 14.7 Unit calcified UNIT CALCED The machine signals when decalcifying becomes necessary.
Switch on your machine by pressing ON/OFF key Press key until you can hear an acoustic signal. EMPTY TRAY (FILL WATER might show as well) Put a sufficiently large container under the coffee-spout (15) in order to prevent cleaning liquid from running into the drip tray. ADD TABLET (Fig. 9) / PRESS CLEANING UNIT CLEANING / PLEASE WAIT EMPTY TRAY PLEASE WAIT RINSE UNIT COFFEE READY The powder funnel for pre-ground coffee should be cleaned after each cleaning process.
FILL WATER Place a container under the pivoting nozzle (20). OPEN TAP PRESS CALC UNIT DECALCIFIYING / PLEASE WAIT Place a container under the height-adjustable tea-spout (22). PRESS CALC UNIT DECALCIFIYING / PLEASE WAIT CLOSE TAP UNIT DECALCIFIYING / PLEASE WAIT Inside the machine the water is conducted to the drip tray. CLEAN CONTACTS / EMPTY TRAY (please refer to chapter 14.8) PLEASE WAIT RINSE UNIT UNIT RINSING COFFEE READY 17.
19. Messages Cause Action FILL WATER Water tank is empty Water level indicator in tank is jammed Tank is calcified, water level indicator is stuck Top up with water Empty tank, rinse out, fill up and replace Remove tank, decalcify, rinse well, fill up with water and replace FILL BEANS Bean container is empty Message still displayed, although beans filled Top up with beans Draw off cup of coffee.
Cause Action You have drawn off coffee 220 times or run the rinsing program 180 times Message still displayed, although machine cleaned Clean as described in chapter 14.
Problem Cause Action Not enough froth while frothing up milk – Frothing nozzle blocked – Clean Auto-Cappuccino – Clean frothing nozzle – Clean Profi Auto-Cappuccino/Caffè Latte – as described in chapter 11.2 If the above mentioned problems and/or messages still persist, please contact your dealer or get in touch directly with Jura Elektroapparate AG. 21. Legal information 22.