IMPRESSA C60/C65 Instructions for Use
Table of contents Your IMPRESSA C60/C65 Control elements 4 Important information 6 Proper use ...................................................................................................................................................... 6 For your safety ............................................................................................................................................... 6 1 Preparing and using for the first time 10 JURA on the Internet .....................................
Table of contents 6 Display messages 40 7 Troubleshooting 42 8 Transport and environmentally friendly disposal 44 Transport / Emptying the system.............................................................................................................44 Disposal.........................................................................................................................................................
Control elements Control elements 9 1 10 11 2 12 3 13 4 14 15 5 6 7 8 1 2 3 4 5 6 7 8 4 Q On/Off button Water tank cover Water tank Mains cable (back of the machine) Height-adjustable coffee spout Coffee grounds container Drip tray Cup grille 9 10 11 12 13 14 15 Filler funnel cover Filler funnel for ground coffee Bean container cover Grinder adjustment switch Bean container with aroma preservation cover Switch for hot water and steam preparation Fine foam frother
Control elements 1 2 3 1 2 Display Rotary Switch 4 5 3 4 5 O c n P symbol (programming) Maintenance symbol Steam symbol The Connector System© permits the use of different cappuccino frothers. These are available from stockists.
Important information Important information Proper use The machine is designed and intended for private domestic use. It should only be used for coffee preparation and to heat milk and water. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use. Before using the machine read these instructions for use thoroughly and completely and comply with the instructions they contain.
Important information U U Never open and repair the machine yourself. Do not modify the machine in any way that is not described in these instructions for use. The machine contains live parts. If opened, there is a danger of potentially fatal injury. Repairs may only be carried out by authorised JURA service centres, using original spare parts and accessories.
Important information U U U U U U U U U U U 8 Do not immerse the IMPRESSA, mains cable or connections in water. Do not put the IMPRESSA or any individual parts in the dishwasher. Switch your IMPRESSA off at the power switch before any cleaning operation. Always wipe the IMPRESSA with a damp cloth rather than a wet one, and protect it from prolonged exposure to water splash. Only connect the machine to the mains voltage in accordance with the information on the rating plate.
Important information U Children aged 8 and over may only operate the machine without supervision if they have been instructed in how to use it safely. Children must be able to recognise and understand the potential dangers arising from incorrect use.
1 Preparing and using for the first time 1 Preparing and using for the first time JURA on the Internet Visit us on the Internet. You can download short operating instructions for your machine from the JURA website (www.jura.com). You will also find interesting and up-to-date information on your IMPRESSA and on every aspect of coffee. Setting up the machine When setting up your IMPRESSA, please note the following: Place the IMPRESSA on a horizontal surface that is not sensitive to water.
1 Preparing and using for the first time J WARNING If the machine is operated with a defective mains cable, there is a danger of potentially fatal electric shock. T Never use a machine which is damaged or has a defective mains cable. Precondition: The bean container has been filled. T Insert the mains plug into a power socket. Q T Press the On/Off button to switch the IMPRESSA on. SPRACHE DE appears on the display. g T Turn the Rotary Switch until the required language is displayed, e.g. LANGUAGE EN.
1 Preparing and using for the first time SWITCH OPEN, the light segment on the switch lights up. T Place one receptacle under the coffee spout and another under the fine foam frother. h T Turn the switch to the m position. FILTER RINSING, water flows out of the fine foam frother. E You can interrupt rinsing of the filter at any time. To do this, turn the switch clockwise. Turn the switch anticlockwise to continue rinsing the filter. E The water may be slightly discoloured.
1 Preparing and using for the first time T Fill the water tank with fresh, cold water and reinsert the tank. SWITCH OPEN, the light segment on the switch lights up. T Place one receptacle under the coffee spout and another under the fine foam frother. h T Turn the switch to the m position. SYSTEM FILLING, the system fills up with water. SWITCH CLOSE j T Turn the switch to the o position. SYSTEM FILLING, the system fills up with water. HEATING, the machine heats up. RINSING, the system is rinsed.
1 Preparing and using for the first time Example: Proceed as follows to change the consistency of grind during the preparation of an espresso. T Place a cup under the coffee spout. T Open the bean container cover and remove the aroma preservation cover. k T Press the Rotary Switch to start preparation. T Turn the grinder adjustment switch to the desired position while the grinder is running. The preset amount of water flows into the cup. Preparation stops automatically. T Fit the aroma preservation cover.
1 Preparing and using for the first time Connecting milk Your IMPRESSA creates fine, creamy, feather-light milk foam with a perfect consistency. The most important requirement for frothing milk is a milk temperature of 4–8 °C. We would therefore recommend using a milk cooler or a vacuum milk container. T Remove the protective cover from the fine foam frother. T Connect the milk pipe to the fine foam frother.
2 Preparation 2 Preparation E You can stop the machine at any time while a speciality coffee, steam or hot water is being prepared. Just press the Rotary Switch (for a speciality coffee) or return the switch to its original position (for steam and hot water). E During the grinding operation you can select the coffee strength of single products by turning the Rotary Switch g: MILD, NORMAL, STRONG or EXTRA.
2 Preparation Two speciality coffees at the touch of a button When you prepare two drinks at once, the amount of water selected for the single product is used for each cup. The preparation of two espressi and two coffees follows this same model. Example: Proceed as follows to prepare two espressi. Precondition: ESPRESSO is displayed (example). T Place two espresso cups under the coffee spout. k T Press the Rotary Switch twice (within 2 seconds), to start preparation of two espressi.
2 Preparation E You can continue to prepare steam for the next 40 seconds or so without the machine having to heat up again. E Touch the Steam symbol n. ESPRESSO appears on the display (example). Now you can prepare speciality coffees again. T Place the cup under the coffee spout. k T Press the Rotary Switch. Coffee preparation starts. The preset amount of water for espresso flows into the cup. Preparation stops automatically. ESPRESSO appears on the display.
2 Preparation E You can continue to prepare steam for the next 40 seconds or so without the machine having to heat up again. To ensure that the fine foam frother always works properly, you must clean it daily when you have been preparing milk (see Chapter 5 ‘Maintenance – Cleaning the fine foam frother’). Your IMPRESSA will not prompt you to clean the fine foam frother. Ground coffee You can choose to use a second coffee variety, for example decaffeinated coffee, with the filter funnel for ground coffee.
2 Preparation T Open the cover of the filler funnel for ground coffee. T Place one level measuring spoon of ground coffee into the filler funnel. T Close the cover of the filler funnel. k T Press the Rotary Switch. ESPRESSO (example) g T Turn the Rotary Switch until COFFEE is displayed. k T Press the Rotary Switch. Preparation starts. COFFEE, the preset amount of water for coffee flows into the cup. Preparation stops automatically. COFFEE appears on the display.
2 Preparation E You can alter this setting at any time by repeating the above procedure. E You can also permanently set the amount of water for all speciality coffees in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Product settings’). Hot water J CAUTION There is a danger of scalding from hot water splashes. T Avoid direct contact with the skin. Example: Proceed as follows to prepare hot water. Precondition: ESPRESSO is displayed (example).
3 3 Daily operation Daily operation Switching on Daily maintenance of the machine and hygiene when handling milk, coffee and water are key to a perfect coffee result in the cup every time. You should therefore change the water daily. T Place a receptacle under the coffee spout. Q T Press the On/Off button to switch the IMPRESSA on. HEATING RINSING, the system is rinsed. The rinse stops automatically. ESPRESSO appears on the display (example). Your IMPRESSA is ready for use.
3 Daily operation E In the interests of hygiene, we recommend changing the milk pipe on a regular basis (approx. every 3 months). Replacement pipes are available from specialised dealers. Switching off When the IMPRESSA is switched off, the system is automatically rinsed if a speciality coffee has been prepared. Precondition: ESPRESSO is displayed (example). Q T Place a receptacle under the coffee spout. T Press the On/Off button. RINSING, the system is rinsed. The operation stops automatically.
4 Permanent settings in programming mode 4 Permanent settings in programming mode You can make permanent settings in programming mode. You can navigate through the programme items and permanently save the required settings simply by turning and pressing the Rotary Switch. You can make the following settings with the Rotary Switch: Programme item Sub-item Explanation RINSE RINSE, CLEAN, FILTER (only if filter T Select the desired maintenance programme.
4 Product settings Product Espresso, coffee 2 cups Permanent settings in programming mode In the programme item BUTTONS you can make individual settings for espresso and coffee. The following permanent settings can be made: Amount Coffee strength Temperature Volume: MILD, NORMAL, STRONG, EXTRA NORMAL, HIGH 25 ML – 240 ML When you prepare two drinks at once, the temperature and amount of water selected for the single product are used for each cup.
4 Permanent settings in programming mode Setting the water hardness The harder the water is, the more frequently the IMPRESSA needs to be descaled. It is therefore important to set the water hardness accurately. The water hardness can be adjusted on a continuous scale between 1 °dH and 30 °dH. E If you are using the CLARIS Blue filter cartridge and have activated it, it is not possible to set the water hardness. Example: Proceed as follows to change the water hardness setting from 16 °dH to 25 °dH.
4 Permanent settings in programming mode Example: Proceed as follows to change the energy-saving mode from ENERGY w to ENERGY -. Precondition: ESPRESSO is displayed (example). O T Touch the P symbol for approximately 2 seconds until RINSE appears on the display. g T Turn the Rotary Switch until ENERGY w is displayed. k T Press the Rotary Switch to enter the programme item. SAVE w g T Turn the Rotary Switch until SAVE - is displayed. k T Press the Rotary Switch to confirm the setting.
4 Permanent settings in programming mode Unit for amount of water In the programme item DISPLAY you can select the unit used for the amount of water. Example: Proceed as follows to change the unit for the amount of water from ML to OZ. Precondition: ESPRESSO is displayed (example). O T Touch the P symbol for approximately 2 seconds until RINSE appears on the display. g T Turn the Rotary Switch until DISPLAY is displayed. k T Press the Rotary Switch to enter the programme item.
5 5 Maintenance Maintenance Your IMPRESSA has the following integrated maintenance programmes: Rinsing the machine (RINSE) Cleaning the machine (CLEAN) Changing the filter (FILTER) (only if filter is activated) Descaling the machine (DESCALE) (only if filter is not activated) U U U U E Clean the machine, change the filter or descale the machine when you are prompted to do so. E You can start the maintenance programmes at any time in programming mode (programme item RINSE).
5 Maintenance Rinsing the fine foam frother E This chapter applies to the professional fine foam frother and the fine foam frother. To ensure that the fine foam frother always works properly, you must rinse it with water after every milk preparation. Your IMPRESSA will not prompt you to rinse the fine foam frother. Precondition: ESPRESSO is displayed (example). T Remove the milk pipe from the milk container or carton. T Fill a receptacle with 250 ml of fresh water.
5 Maintenance Precondition: ESPRESSO is displayed (example). T Remove the milk pipe from the milk container or carton. T Pour 250 ml of fresh water into a receptacle and add one capful of milk system cleaner. T Immerse the milk pipe in the receptacle. T Place a receptacle under the fine foam frother. n T Touch the Steam symbol. HEATING / STEAM As soon as the machine has heated up, STEAM / READY appears, the light segment on the switch lights up. h T Turn the switch to the m position.
5 Maintenance T Dismantle the fine foam frother into its individual parts. T Rinse all the parts of the fine foam frother thoroughly under running water. If there are severely dried-on milk residues, firstly immerse the individual parts in JURA milk system cleaner and then rinse them thoroughly. T Re-assemble the fine foam frother. E Ensure that all individual parts are correctly and firmly connected to ensure optimum operation. T Firmly attach the fine foam frother to the Connector System©.
5 Inserting and activating the filter Maintenance Your IMPRESSA no longer has to be descaled if you are using the CLARIS Blue filter cartridge. If you did not activate the filter cartridge the first time you used the machine, you can do this now as follows. E Perform the ‘inserting the filter’ operation without any interruptions. This will ensure that your IMPRESSA always produces its best. Precondition: ESPRESSO is displayed (example).
5 Maintenance E You can interrupt rinsing of the filter at any time. To do this, turn the switch clockwise. Turn the switch anticlockwise to continue rinsing the filter. E The water may be slightly discoloured. This is not harmful to health and does not affect the taste. Rinsing of the filter stops automatically after approximately 500 ml. SWITCH CLOSE appears on the display. j T Turn the switch to the o position. HEATING, the machine heats up. ESPRESSO appears on the display (example).
5 Maintenance T Place a receptacle (at least 500 ml) under the fine foam frother. c T Touch the Maintenance symbol. SWITCH OPEN, the light segment on the switch lights up. h T Turn the switch to the m position. FILTER RINSING, water flows out of the fine foam frother. E You can interrupt rinsing of the filter at any time. To do this, turn the switch clockwise. Turn the switch anticlockwise to continue rinsing the filter. E The water may be slightly discoloured.
5 Maintenance c c T Place a receptacle under the coffee spout. T Touch the Maintenance symbol. CLEANING, water flows out of the coffee spout. The operation is interrupted, ADD TABLET. T Open the cover of the filler funnel for ground coffee. T Insert a JURA cleaning tablet into the filler funnel. T Close the cover of the filler funnel. T Touch the Maintenance symbol. CLEANING, water flows out of the coffee spout several times. The operation stops automatically.
5 CAUTION Maintenance If the descaling agent comes into contact with sensitive surfaces (e.g. marble), damage cannot be ruled out. T Clean up any splashes immediately. E The descaling programme lasts approximately 45 minutes. E JURA descaling tablets are available from specialised dealers. E If you use a CLARIS Blue filter cartridge and this is activated, you will not be prompted to descale. Precondition: DESCALE / ESPRESSO is displayed (example).
5 Maintenance T Empty the receptacle and place it back under the Connector System©. T Place another receptacle under the coffee spout. T Remove the water tank and rinse it thoroughly. T Fill the water tank with fresh, cold water and reinsert the tank. SWITCH OPEN, the light segment on the switch lights up. h T Turn the switch to the m position. DESCALE, the descaling operation is continued. The operation is interrupted, SWITCH CLOSE. j T Turn the switch to the o position.
5 Descaling the water tank Maintenance Limescale deposits may form in the water tank. To ensure correct function of the machine, descale the water tank from time to time. T Remove the water tank. T If you use a CLARIS Blue filter cartridge, remove this. T Descale the tank with a mild conventional descaling agent in accordance with the manufacturer's instructions. T Rinse out the water tank thoroughly. T If you use a CLARIS Blue filter cartridge, insert this again.
6 Display messages 6 Display messages Message FILL TANK EMPTY GROUNDS TRAY MISSING FILL BEANS PRESS RINSE FILTER / ESPRESSO Cause/Result The water tank is empty. You cannot prepare any products. (example) DESCALE / ESPRESSO T Empty the coffee grounds container and the drip tray (see Chapter 3 ‘Daily operation – Daily maintenance’). The IMPRESSA is prompting you to continue a previously started maintenance programme. The filter cartridge no longer works.
6 Display messages Message TOO HOT Cause/Result The system is too hot to start a maintenance programme. Action T Wait for several minutes until the system has cooled or prepare a speciality coffee or hot water.
7 Troubleshooting 7 Troubleshooting Problem Insufficient foam is produced when the milk is frothed or milk sprays out of the fine foam frother. Cause/Result The fine foam frother is dirty. Coffee only comes out Coffee or ground coffee in drips when it is being has been ground too finely and is blocking the system. prepared. The same filter cartridge may have been used several times or the water hardness set incorrectly in the programming mode. Water hardness cannot The CLARIS Blue filter be adjusted.
7 Problem Other ERROR messages are displayed. Cause/Result – Troubleshooting Action Switch the machine off with the On/Off button. Contact customer support in your country (see Chapter 11 ‘JURA contact details / Legal information’). E If you were unable to solve the problem, contact customer support in your country (see Chapter 11 ‘JURA contact details / Legal information’).
8 8 Transport and environmentally friendly disposal Transport and environmentally friendly disposal Transport / Emptying the system Keep the packaging for your IMPRESSA. It should be used to protect the machine during transport. In order to protect the IMPRESSA from frost during transport, the system must be emptied. Precondition: ESPRESSO is displayed (example). T Remove the milk pipe from the fine foam frother. T Place a receptacle under the fine foam frother. n T Touch the Steam symbol.
9 Technical data 9 Technical data Voltage Power Conformity mark Energy consumption 220–240 V ~, 50 Hz 1450 W AS Approx. 9 Wh ENERGY w Energy consumption Approx. 15 Wh ENERGY Pump pressure Holding capacity of water tank Holding capacity of bean container Holding capacity of coffee grounds container Cable length Weight Dimensions (W H D) Static, max. 15 bar 1.9 l 200 g Max. 16 portions Approx. 1.1 m Approx. 9.6 kg 28 34.
10 Index 10 A B C D Index Addresses 48 Aroma preservation cover Bean container with aroma preservation cover 4 Automatic switch-off 27 Bean container Bean container with aroma preservation cover 4 Cleaning 38 Filling 10 Bus bar Technical data 45 Button On/Off button 4 Cappuccino 17 Cappuccino frother rinsing 30 CLARIS Blue filter cartridge Changing 34 Inserting and activating the filter 33 Cleaning Bean container 38 Fine foam frother 30 Machine 35 Coffee 16 Coffee grounds container 4 Coffee spout Hei
10 L M P Language 28 Machine Cleaning 35 Descaling 36 Rinsing 29 Setting up 10 Switching off 23 Switching on 22 Mains cable 4 Maintenance 29 Daily maintenance 22 Messages, display 40 Milk Connecting milk 15 Milk foam 18 Permanently setting the water for the cup size 20 Permanent settings in programming mode 24 Preparation 16 Cappuccino 17 Coffee 16 Espresso 16 Ground coffee 19 Hot water 21 Milk foam 18 Two speciality coffees 17 Problems Troubleshooting 42 Product settings 25 Professional fine foam frothe
J71670/C60-C65/en/201611 11 JURA contact details / Legal information 11 JURA contact details / Legal information JURA Elektroapparate AG Kaffeeweltstrasse 10 CH-4626 Niederbuchsiten Tel. +41 (0)62 38 98 233 @ You will find additional contact details for your country at www.jura.com.