E8/E80 Instructions for Use
Table of contents Your E8/E80 Control elements 4 Important information 6 Proper use ...................................................................................................................................................... 6 For your safety ............................................................................................................................................... 6 1 Preparing and using for the first time 10 JURA on the Internet ...............................................
Table of contents 6 7 8 9 10 11 Descaling the machine .............................................................................................................................. 32 Cleaning the bean container .....................................................................................................................34 Descaling the water tank ...........................................................................................................................
Control elements Control elements 9 1 10 2 11 3 4 5 12 6 13 7 8 1 2 3 4 5 6 7 8 4 14 Filler funnel cover Filler funnel for ground coffee Bean container with aroma preservation cover Water tank cover Water tank Mains cable (back of the machine) Coffee grounds container Drip tray 9 10 11 12 13 14 Cover cap for grinder adjustment switch Grinder adjustment switch On/Off button Q Connector System© with professional fine foam frother Height-adjustable coffee spout Cup grille
Control elements 1 2 1 Display 2 Multi-function buttons (button function depends on what is shown in the display) Fine foam frother (used in different model variants) Accessories Container for milk system cleaning Measuring spoon for ground coffee Hot-water nozzle 6 5
Important information Important information Proper use The machine is designed and intended for private domestic use. It should only be used for coffee preparation and to heat milk and water. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use. Before using the machine read these instructions for use thoroughly and completely and comply with the instructions they contain.
Important information U U U U which is available directly from JURA or from authorised JURA service centres. Make sure that the JURA and the mains cable are not located close to hot surfaces. Be careful to ensure that the mains cable is not trapped and does not rub against sharp edges. Never open and repair the machine yourself. Do not modify the machine in any way that is not described in these instructions for use. The machine contains live parts.
Important information U U U U U U U U U U U U 8 Protect the JURA from environmental influences such as rain, frost and direct sunlight. Do not immerse the JURA, mains cable or connections in water. Do not put the JURA or any individual parts in the dishwasher. Before cleaning, switch your JURA off with the On/Off button. Always wipe the JURA with a damp cloth rather than a wet one, and protect it from prolonged exposure to water splash.
Important information U U U Do not allow children to play with the machine. Keep children under the age of 8 away from the machine, or supervise them constantly. Children aged 8 and over may only operate the machine without supervision if they have been instructed in how to use it safely. Children must be able to recognise and understand the potential dangers arising from incorrect use.
1 Preparing and using for the first time 1 Preparing and using for the first time JURA on the Internet Visit us on the Internet. You can download short operating instructions for your machine from the JURA website (www.jura.com). You will also find interesting and up-to-date information on your JURA and on every aspect of coffee. Setting up the machine When setting up your JURA, please note the following: Place the JURA on a horizontal surface that is not sensitive to water.
1 Preparing and using for the first time T You will then be able to read the degree of water hardness from the discolouration of the Aquadur® test strip and the description on the packaging. First-time use When using the machine for the first time, you can choose whether you want to operate JURA with or without the CLARIS Smart filter cartridge. If the water hardness is 10 °dH or more, we recommend using the filter cartridge.
1 Preparing and using for the first time E Now decide whether you want to operate your JURA with or without a CLARIS Smart filter cartridge. Operation with filter cartridge: go straight to the next section (see Chapter 1 ‘Preparing and using for the first time – First-time use with filter cartridge activation’). Operation without filter cartridge (see Chapter 1 ‘Preparing and using for the first time – First-time use without filter cartridge activation’).
1 Preparing and using for the first time Rinsing of the filter stops automatically after approximately 300 ml. ‘System is filling’, the system fills up with water. ‘Empty drip tray’ T Empty the drip tray and coffee grounds container and put them back into the machine. ‘Machine is rinsing’, the system is rinsed. Water flows out of the coffee spout. The rinse stops automatically. Your JURA is ready for use. E The start screen shows the products you can prepare.
1 Preparing and using for the first time E The start screen shows the products you can prepare. Press the ‘ > ’ button to display more products. Connecting milk é Your JURA creates fine, creamy, feather-light milk foam with a perfect consistency. The most important requirement for frothing milk is a milk temperature of 4–8 °C. We would therefore recommend using a milk cooler or a vacuum milk container. T Remove the protective cover from the fine foam frother.
2 Preparation 2 Preparation E The display shows four products you can prepare. Press the ‘ > ’ button to display more products. E You can stop the machine at any time while a speciality coffee or hot water is being prepared. Just press any button. E During the grinding operation you can select the coffee strength of single products by pressing the ‘ < ’ and ‘ > ’ buttons. E During preparation you can change the preset amounts (e.g. water and amount of milk) by pressing the ‘ < ’ and ‘ > ’ buttons.
2 Preparation E There is a short interval while the hot milk separates from the milk foam. This allows the typical layers of a latte macchiato to form. You can choose the length of this interval in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Adjusting the product settings’). Coffee preparation starts. The preset amount of water for espresso flows into the glass. Preparation stops automatically. Your JURA is once more ready for use.
2 Preparation E This chapter applies to the professional fine foam frother and the fine foam frother. Milk foam Example: Proceed as follows to prepare milk foam. Precondition: The speciality coffees with milk are displayed. Milk is connected to the fine foam frother. T Place a cup under the fine foam frother. é è E If you are using the professional fine foam frother, turn the selector switch to the Milk Foam position é.
2 Preparation Example: Proceed as follows to prepare one espresso using ground coffee. Precondition: The speciality coffees are displayed. T Place an espresso cup under the coffee spout. T Open the powder chute cover. ‘Ground coffee’ / ‘Please add ground coffee’ T Place one level measuring spoon of ground coffee into the filler funnel. T Close the cover of the filler funnel. T Press the ‘Espresso’ button. Preparation starts. ‘Espresso’ appears and the preset amount of water for espresso flows into the cup.
2 Preparation Adjusting the grinder CAUTION You can adjust the grinder on a continuous scale to suit the degree of roast of your coffee. If you adjust the consistency of grind when the grinder is not operating, the grinder adjustment switch could be damaged. T Only adjust the consistency of grind when the grinder is running. The consistency of grind is correct if the coffee flows regularly from the coffee spout. In addition a fine, thick crema forms.
3 3 Daily operation Daily operation Filling the water tank Daily maintenance of the machine and hygiene when handling milk, coffee and water are key to a perfect coffee result in the cup every time. You should therefore change the water daily. CAUTION Milk, sparkling mineral water or other liquids can damage the water tank or the machine. T Only fill the water tank with fresh, cold water. T Open the water tank cover. T Remove the water tank and rinse it with cold water.
3 Daily operation T Clean the fine foam frother (see Chapter 5 ‘Maintenance – Cleaning the fine foam frother’). T Remove the milk pipe and rinse it thoroughly under running water. T Dismantle and rinse the fine foam frother (see Chapter 5 ‘Maintenance – Dismantling and rinsing the professional fine foam frother’). T Wipe the surface of the machine with a clean, soft, damp cloth (e.g. microfibre cloth).
4 Permanent settings in programming mode 4 Permanent settings in programming mode Press the ‘ Pc ’ button to enter programming mode. You can navigate through the programme items and permanently save the required settings using the multi-function buttons.
4 Product Latte macchiato Coffee strength 8 levels Portion of milk Hot water – – Permanent settings in programming mode Amount Coffee: 25 ml – 240 ml Milk: 3 sec. – 120 sec. Interval: 0 sec. – 60 sec. Milk: 3 sec. – 120 sec. Water: 25 ml – 450 ml Temperature normal, high – low, normal, high Permanent settings in programming mode always follow the same model. Example: Proceed as follows to change the coffee strength for one coffee. T Press the ‘ Pc ’ button.
4 Permanent settings in programming mode T Press the ‘ Pc ’ button. T Press the ‘ > ’ button several times until ‘4/5’ is displayed. T Press the ‘Switch off after’ button. ‘Switch off after’ T Press the ‘ < ’ or ‘ > ’ button to change the switch-off time. T Press the ‘Save’ button. ‘Saved’ appears briefly on the display. ‘4/5’ T Press the ‘’ button to exit programming mode. Setting the water hardness The harder the water is, the more frequently the JURA needs to be descaled.
4 Permanent settings in programming mode T Press the ‘ Pc ’ button. T Press the ‘ > ’ button several times until ‘4/5’ is displayed. T Press the ‘Rinse the milk system’ button. ‘Rinse the milk system’ T Press the ‘Automatic’ button. T Press the ‘Save’ button. ‘Saved’ appears briefly on the display. ‘4/5’ T Press the ‘’ button to exit programming mode. Unit for amount of water Example: Proceed as follows to change the unit for the amount of water from ‘ml’ to ‘oz’. T Press the ‘ Pc ’ button.
5 5 Maintenance Maintenance Your JURA has the following integrated maintenance programmes: Rinsing the machine (‘Rinse the coffee system’) Rinsing the fine foam frother (‘Rinse the milk system’) Cleaning the fine foam frother (‘Clean the milk system’) Changing the filter (‘Change the filter’) Cleaning the machine (‘Clean’) Descaling the machine (‘Descale’) U U U U U U E Carry out each maintenance programme when you are prompted to do so.
5 é è Cleaning the fine foam frother Maintenance Precondition: ‘Rinse the milk system’ is displayed. T Place a receptacle under the fine foam frother. T Press the ‘ Pc ’ button. T Press the ‘ > ’ button. T Press the ‘Rinse the milk system’ button to start the rinse operation. ‘Milk system is being rinsed’ appears and the fine foam frother is rinsed. The operation stops automatically. E This chapter applies to the professional fine foam frother and the fine foam frother.
5 Maintenance T Connect the milk pipe to the container. é è 6 é è Dismantling and rinsing the professional fine foam frother é è E To connect the milk pipe to the container correctly, the pipe must be fitted with a connector. T Press the ‘Next’ button. ‘Milk system is being cleaned’ appears and the fine foam frother and the milk pipe are cleaned. T During the first brief interruption, set the setting wheel of the professional fine foam frother to the Milk position è.
5 Dismantling and rinsing the fine foam frother Maintenance To make sure the fine foam frother works properly, and in the interests of hygiene, it must be dismantled and rinsed daily if you have been preparing milk. Your JURA will not prompt you to dismantle and rinse the frother. T Remove the milk pipe and rinse it thoroughly under running water. T Carefully remove the fine foam frother from the Connector System© by twisting slightly. T Dismantle the fine foam frother into its individual parts.
5 Maintenance E The machine automatically detects that you have just inserted the filter cartridge. ‘Saved’ appears briefly on the display. ‘Filter is being rinsed’, water flows out of the fine foam frother. E The water may be slightly discoloured. This is not harmful to health and does not affect the taste. Rinsing of the filter stops automatically after approximately 300 ml. The start screen is displayed. E If the filter is active, this is indicated by a blue filter symbol at the bottom of the display.
5 Maintenance E The water may be slightly discoloured. This is not harmful to health and does not affect the taste. Rinsing of the filter stops automatically after approximately 300 ml. The start screen is displayed. Cleaning the machine After 180 preparations or 80 switch-on rinses, the JURA will prompt you to clean it. CAUTION If the wrong cleaning agent is used, the machine could be damaged and/or traces could be left behind in the water. T Use only original JURA maintenance products.
5 Maintenance T Empty the drip tray and coffee grounds container and put them back into the machine. Cleaning is now complete. The start screen is displayed. Descaling the machine The JURA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the hardness of your water. E If you are using a CLARIS Smart filter cartridge, you will not be prompted to descale.
5 Maintenance T Completely dissolve the contents of one blister (3 JURA descaling tablets) in a receptacle holding 500 ml of lukewarm water. This may take several minutes. T Pour the solution into the empty water tank and insert it into the machine. é è é è T Place a receptacle under the fine foam frother. T Press the ‘Next’ button. ‘Machine is being descaled’ appears and water flows out of the fine foam frother repeatedly. The operation is interrupted, ‘Empty drip tray’.
5 Maintenance Cleaning the bean container Coffee beans may be covered with a slight oil film which remains on the walls of the bean container. These traces may negatively affect the coffee result. For this reason clean the bean container from time to time. Precondition: ‘Fill bean container’ is displayed. T Switch the machine off with the On/Off button Q. T Remove the aroma preservation cover. T Clean the bean container with a soft, dry cloth.
6 Display messages 6 Display messages Message ‘Fill water tank’ Cause/Result The water tank is empty. You cannot prepare any products. ‘Empty coffee grounds container’ The coffee grounds container T Empty the coffee grounds container is full. You cannot prepare any and the drip tray (see Chapter 3 ‘Daily products. operation – Daily maintenance’). The drip tray is not inserted T Fit the drip tray. correctly or is not inserted at all. You cannot prepare any products. The bean container is empty.
7 Troubleshooting 7 Troubleshooting Problem Insufficient foam is produced when the milk is frothed or milk sprays out of the fine foam frother. Coffee only comes out in drips when it is being prepared. Cause/Result Action The fine foam frother is dirty. T Clean the fine foam frother (see Chapter 5 ‘Maintenance – Cleaning the fine foam frother’). T Dismantle and rinse the fine foam frother (see Chapter 5 ‘Maintenance – Dismantling and rinsing the professional fine foam frother’).
7 Problem Other ‘ERROR’ messages are displayed. Cause/Result Troubleshooting Action – T Switch the JURA off with the On/Off button Q. Contact customer support in your country (see Chapter 11 ‘JURA contact details / Legal information’). E If you were unable to solve the problem, contact customer support in your country (see Chapter 11 ‘JURA contact details / Legal information’).
8 8 Transport and environmentally friendly disposal Transport and environmentally friendly disposal Transport / Emptying the system Keep the packaging for your JURA. It should be used to protect the machine during transport. In order to protect the JURA from frost during transport, the system must be emptied. é Disposal 38 è Precondition: The speciality coffees with milk are displayed. T Remove the milk pipe from the fine foam frother. T Place a receptacle under the fine foam frother.
9 Technical data 9 Technical data Voltage Power Conformity mark Pump pressure Holding capacity of water tank (without filter) Holding capacity of bean container Holding capacity of coffee grounds container Cable length Weight Dimensions (W H D) 220–240 V ~, 50 Hz 1450 W A static, max. 15 bar 1.9 l 280 g max. 16 portions approx. 1.1 m approx. 9.8 kg 28.0 35.1 43.
10 Index 10 A B C Index Addresses 44 Adjusting the product settings 22 Aroma preservation cover Bean container with aroma preservation cover 4 Automatic switch-off 23 Bean container Bean container with aroma preservation cover 4 Cleaning 34 Filling 10 Bus bar Technical data 39 Button On/Off button 4 Cappuccino 15 Central grounding point 39 CLARIS Smart filter cartridge Change 30 Insert 29 Cleaning Bean container 34 Fine foam frother 27 Machine 31 Coffee 16 Two coffees 16 Coffee grounds container 4 Cof
10 I J L M P Latte macchiato 15 Milk foam 17 Ristretto 16 Two coffees 16 Two espressi 16 Two ristretti 16 Two speciality coffees 16 Problems Troubleshooting 36 Product settings Adjusting 22 Professional fine foam frother 4 Dismantling and rinsing 28 Programming mode 22 Automatic switch-off 23 Language 25 Milk system rinsing 24 Setting the water hardness 24 Unit for amount of water 25 Proper use 6 Instant coffee Ground coffee 17 Internet 10 JURA Contact details 44 Internet 10 Language 25 Latte macchiat
10 T U Index Technical data 39 Tel 44 Transport 38 Troubleshooting 36 Two products 16 Unit for amount of water 25 Use, First-time 11 W Water hardness Determining the water hardness 10 Setting the water hardness 24 Water tank 4 Descaling 34 Filling 20 Website 10 42
J72215/E8-E80/en/201510 11 JURA contact details / Legal information 11 JURA contact details / Legal information JURA Elektroapparate AG Kaffeeweltstrasse 10 CH-4626 Niederbuchsiten Tel. +41 (0)62 38 98 233 @ You will find additional contact details for your country at www.jura.com.
