IMPRESSA E70/75 Art. Nr.
Jura Impressa E70/75 English. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 – 19 Legend: DISPLAY: serves as information. DISPLAY: please follow the instructions shown. = Note = Important = Tip Jura Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www.juraworld.
Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig.
Operating elements Jura Impressa E70/75 10 11 9 12 8 7 6 5 4 3 2 1 13 14 15 16 1 2 3 4 5 6 7 8 8a 8b 9 10 11 12 13 14 15 16 17 18 Water quantity switch Powder coffee selection switch Coffee key for 2 cups Rinsing-, cleaning-, descaling key Coffee key for 1 cup ON/OFF switch Display dialogue system Key P Key Key Water tank with carrying handle Height-adjustable coffee spout Pre-ground coffee filler funnel Cover for bean container Selector switch for hot water/steam Pivoting nozzle for hot water/s
Contents Jura Impressa E70/75 11.1 Programming Filter................................page 11 11.2 Programming water hardness ...................page 11 11.3 Programming Aroma ..............................page 11 1. Description....................................................page 6 11.4 Programming automatic switch-off time ......page 11 2. Safety instructions ..........................................page 6 11.5 Cup counter..........................................page 11 2.1 Warnings......
Important information for the user 2. Safety instructions Thank you for choosing this Jura product. 2.1 Warnings Please study these instructions carefully before using your new machine for the first time and keep them in safe place for easy reference in future. Should you require further information or should particular problems occur that are not dealt with in sufficient detail for you in these operating instructions, please contact your local dealer or us for the information you require.
3. Preparation of the machine 3.1 Checking the mains voltage The machine is set to the correct voltage before leaving our factory. Ensure that your mains voltage corresponds to the details quoted on the rating plate attached to the bottom of the machine. 3.2 Checking the fuse The machine is designed for a current of 10 Amps. Check that the fuse used matches this. 3.3 Filling the water tank Remove the water tank and rinse it out well with cold tap water (Fig. 1).
The symbols on the display mean: HARDNESS LEVEL — Water hardness function switched off HARDNESS LEVEL 1 German water hardness 1 – 7° French water hardness 1.79 – 12.53° HARDNESS LEVEL 2 German water hardness 8 – 15° French water hardness 14.32 – 26.85° HARDNESS LEVEL 3 German water hardness 16 – 23° French water hardness 28.64 – 41.14° HARDNESS LEVEL 4 German water hardness 24 – 30° French water hardness 42.96 – 53.7° The machine is adjusted to HARDNESS LEVEL 3 in the factory.
6. Adjusting the water quantity The water quantity can be infinitely adjusted with rotary knob (1). The small key means little water for espresso, the large cup means a lot of water for coffee. SELECT PRODUCT Turn the water quantity rotary knob into the position at which the required amount of water appears on the display: 130 ML – 90 ML ESPRESSO 100 ML – 240 ML COFFEE You can also alter the water quantity during the process. Simply turn the water quantity rotary knob (1) to more or less ml.
Never use water-soluble instant coffee or quick coffee. We recommend that you only use powder from freshly ground coffee beans or pre-ground, vacuum-packed coffee. Never put more than 2 portions of coffee in. The filler funnel is not a storage container. Make sure that the coffee powder which you use is not ground too finely. This can lead to blockages, and the coffee then only runs through drip by drip.
When you have reached the required quantity of hot water, turn the steam/hot water rotary knob (15) back to the position . SELECT PRODUCT At the start of a water draw-off, there can be splashes. The pivoting nozzle gets hot. Please avoid direct contact with the skin. 10. Switching machine off When the machine is switched off, the rinsing programme is automatically started. Therefore, place an empty container under the coffee-spout and press the ON/OFF switch.
EXIT Press the key P to return to stand-by status. 12. Care and maintenance 12.1 Fill water FILL WATER When this display lights up, no drawing-off is possible. Fill with water as described under point 3.3. 12.2 Empty grounds container The grounds container collects the coffee grounds. EMPTY GROUNDS When this display lights up, no drawing-off is possible and the grounds container must be emptied (Fig. 6). Remove the drip tray. Be careful, as there is water in it. 12.
12.8 Insert filter Pull up the cartridge holder. Pressing gently, put the filter cartridge into the water tank (Fig. 7). Close the cartridge holder until it engages audibly. Fill the water tank with cold fresh tap water and put it back into the machine. Switch the machine on with the ON/OFF switch. Press the key P until you hear an acoustic signal. FILTER NO Press the key P, and an acoustic signal is heard NO flashes You can change the setting by pressing the keys and . YES flashes.
12.10 General cleaning instructions Never use abrasive articles or corrosive chemicals to clean your machine. Wipe down the casing on the inside and out using a soft, damp cloth. Clean the pivoting nozzle after each use. After heating milk, draw off a little hot water in order to clean the inside of the pivoting nozzle. You can take off the frothing aid for a thorough cleaning (Fig. 8). The water tank should be rinsed out every day and filled with clean water.
ADD TABLET (Fig. 9) / PRESS RINSE UNIT CLEANING / PLEASE WAIT An acoustic signal can be heard. EMPTY TRAY Wait for about 10 seconds before you put the drip tray back in again. PRESS RINSE UNIT CLEANING / PLEASE WAIT An acoustic signal can be heard. EMPTY TRAY SELECT PRODUCT After each cleaning operation the filler funnel for the 2nd coffee type should be cleaned. 14. Descaling The machine has an integrated de-scaling programme.
FILL WATER / OPEN TAP / PRESS RINSE Turn the selector switch for coffee or hot water / steam (13) to position and press the rinsing key . UNIT DECALCING / PLEASE WAIT An acoustic signal is heard. EMPTY TRAY CLOSE TAP UNIT DECALCING / PLEASE WAIT The water is guided into the drip tray in the interior of the machine. An acoustic signal is heard. EMPTY TRAY RINSE MACHINE SELECT PRODUCT 15.
. Messages Cause Action SYSTEM EMPTY System empty Fill system (see point 4.1) FILL WATER The tank is empty Fill with water Floater defective Rinse out or descale water tank The bean container is empty Fill up with beans Although beans have been poured in, the display remains on Draw off a cup of coffee. ”FILL BEANS” only goes off after a draw-off Grounds container full Empty grounds container Tray replaced too early after emptying Only replace the tray after about 10 sec.
. Problems Problem Cause Action Grinder is very noisy – foreign body in grinder – Drawing off coffee with pre-ground powder – is still possible – Have machine examined by Jura service centre Not enough froth when frothing milk – frothing aid blocked – frothing aid in wrong position – clean frothing aid – draw off steam (see point 8) When drawing off coffee, the coffee only flows in drips – grinding too fine – Coffee powder ground too finely – set the grinder to a coarser grind – Use a more coar
. Legal information 20. Technical data These operating instructions contain the information necessary for the correct use, operation and maintenance of the machine. Understanding of and complying with the directions contained in these operating instructions are essential for use of the machine without risk and for safety in operation and maintenance. The operation instructions cannot cover every imaginable example of use. The machine has been designed for use in private households.
