IMPRESSA F50 / F5 / F505 Instructions for use
Legend: DISPLAY: serves as information. DISPLAY: please follow the instructions shown.
Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 18 Fig. 19 Fig. 14 Fig. 15 Fig. 16 Fig.17 Temp. max. Fig. 20 Temp. min.
Control elements 11 22 1. Rotary Switch 13 2. Illuminated ring 3. ON/OFF key 4. Programming key 5. Draw-off key 1 cup Rotary Switch 6. Draw-off key 2 cups 12 8. Steam pre-selection key 10 9 7. Maintenance key 13 3 4 5 6 7 8 9. Display dialog system 10. Water tank with carrying handle 2 14 11. Filler funnel for pre-ground coffee: 12. Bean tank cover 1 15/16 13. Aroma preservation cover 14. Steam/hot water draw-off valve 15. Professional Cappuccino Frother with milk pipe 17 18 16.
Contents 1. Safety information..........................................page 1.1 Warning ..............................................page 1.2 Precautions ..........................................page 2. Preparing the IMPRESSA................................page 2.1 Check supply voltage ..............................page 2.2 Check electrical fuse ..............................page 2.3 Fill water tank......................................page 2.4 Fill coffee beans....................................page 2.
Introduction 1.2 Precautions Thank you for purchasing the IMPRESSA. To ensure perfect functioning of your IMPRESSA, carefully read this operating manual and keep it for future reference. Should you need more information or if you encounter particular problems not specified in these operating instructions in sufficient detail, either contact us directly or contact your local authorized dealer.
2.3 Fill water tank Only use fresh, cold water. Never fill in milk, mineral water or other liquids. Remove the water tank and rinse it with cold tap water thoroughly (Fig. 4). Then fill the water tank and reinstall it. Make sure to install the tank properly, it must engage audibly. 2.
FILLING SYSTEM CLOSE TAP Close the steam / hot water draw-off tap (14). HEATING PRESS RINSE Press the maintenance key (7). Machine carries out a rinsing operation. RINSING READY If BEANS FILL is displayed, press the coffee draw-off key again. Machine not filled with coffee beans yet. To get an excellent crema, adjust the coffee spout (17) to the size of your cup (Fig. 3). 4. Adjusting the water hardness Water is heated in the IMPRESSA.
5. Installation of CLARIS plus filter cartridges If the CLARIS plus filter cartridge is installed properly, descaling of the coffee machine is no longer required. For more information on the CLARIS plus filter cartridge refer to brochure «CLARIS plus. Hard on limescale. Gentle on your coffee machine.» 5.1 Installing the filter Fold up the cartridge holder. Install the filter cartridge in the water tank, applying a gentle pressure (Fig. 1). Fold down the cartridge holder again until it engages audibly.
Open the steam / hot water draw-off tap (14). HEATING READY Turn the Rotary Switch (1) until the required water quantity is displayed. For example, 120 ML 6. Rinsing the IMPRESSA 8. Drawing off 1 cup of coffee When the IMPRESSA is switched off and has cooled down, a rinsing operation is started when the machine is switched on again. When the machine is switched off, a rinsing operation is started automatically.
For Example: 160 ML For Example: MILD Your product is being prepared. READY 9. Drawing off 2 cups of coffee Selecting the coffee strength is not possible when drawing off 2 cups of coffee. You will draw off 2 mild cups automatically. You can adjust the water quantity before the draw-off operation using the Rotary Switch (1). The adjusted value (ML) refers to 1 cup. You can stop the draw-off operation at any time by pressing any coffee draw-off key.
For Example: 210 ML POWDER Your product is being prepared. READY Close the steam / hot water draw-off tap (14). READY 11. Drawing off hot water 12. Drawing off steam If you do not change the settings using the Rotary Switch (1), the water quantity last adjusted will be drawn off automatically. The Steam function is used for preparing milk foam and hot milk as well as for the Professional Cappuccino Frother (15) cleaning program. Install the hot water nozzle (see Fig.
You can adjust the steam dispensing time individually by turning the Rotary Switch (1) until the required SEC are displayed on the screen. For example, 35 SEC If you do not change the steam dispensing time with the Rotary Switch (1), the machine will set the steam quantity according to the previously used settings. While drawing off steam, STEAM is shown on the display. Once the desired steam quantity has been reached, CLOSE TAP appears on the display.
The illuminated ring (2) is active. You can adjust the steam dispensing time individually by turning the Rotary Switch (1) until the required SEC are displayed on the screen. For example, 35 SEC If you do not change the steam dispensing time with the Rotary Switch (1), the machine will set the steam quantity according to the previously used settings. Adjust the steam dispensing time to suit the size of your cup. While drawing off steam, STEAM is shown on the display.
The IMPRESSA will not prompt you to clean the Professional Cappuccino Frother. The JURA Auto-Cappuccino Cleaner is available from stockists. Place a container under the Professional Cappuccino Frother (Fig. 9). Fill a second container with 250 ml of fresh water and add one capful of Auto-Cappuccino Cleaner. Immerse the milk pipe into the container with the Auto-Cappuccino Cleaner (Fig. 9). READY Press the steam pre-selection key (8).
Time Automatic switch-on time Automatic switch-off time Draw-offs Language Display Programming key (4) Use the programming key (4) to open or quit the programming mode (no saving of values effected). Rotary switch Turn the Rotary Switch to change the adjusted values or to select the next programming step. Press the Rotary Switch to check the values adjusted or to save the values selected 15.1 Programming the filter Refer to Chapter 5.1 «Inserting the filter». 15.
Press the programming key (4) to quit the programming mode or select the next programming item using the Rotary Switch (1). READY 15.5 Programming the time You must programme the time if you want to use the automatic switch-on function. READY Press programming key (4) until FILTER appears. The illuminated ring (2) is active. Turn the Rotary Switch (1) until TIME is displayed. TIME Now press the Rotary Switch (1) to start programming the time.
15.7 Programming the automatic switch-off time You can programme your coffee machine such that it will switch off automatically after a certain time. You can programme the switch-off time in a range between 0.5 and 9 hours, or select ––:–– (i.e. inactive). READY Press programming key (4) until FILTER appears. The illuminated ring (2) is active. Turn the Rotary Switch (1) until OFF AFT. HR is displayed. OFF AFT. HR Now press the Rotary Switch (1) to start programming the switch-off time.
LANGUAGE Now press the Rotary Switch (1) to start programming the item LANGUAGE. Turn the Rotary Switch (1) until the required language is displayed. For example ENGLISH Press the Rotary Switch (1) to save the selected language LANGUAGE Press the programming key (4) to quit the programming mode or select the next programming item using the Rotary Switch (1). READY 15.
READY The water tank should be rinsed daily and refilled with fresh water. Only fill in fresh, cold water. Never fill in milk, mineral water or other liquids. 16.4 Fill coffee beans FILL BEANS Refill beans as described in Chapter 2.4. The message REFILL BEANS will disappear after you draw off your next cup of coffee. 16.2 Emptying the coffee grounds container EMPTY GROUNDS If this message appears on the display, you can no longer draw off coffee.
16.7 IMPRESSA decalcify 16.9 Emptying the system During operation, the machine will calcify. The degree of scaling depends on the hardness of the water in your region. The machine will inform you when de-scaling is required. You can still draw off coffee or hot water/steam. However, we recommend that you should de-scale the machine (Chapter 18) within the next few days. Precondition: IMPRESSA switched off READY DECALCIFY 16.
Press the maintenance key (7) until the following message is displayed: EMPTY TRAY Empty the tray NO TRAY Insert the tray again. Remove the drip grate (19). Put a container (Fig. 12) under the adjustable coffee spout (17). PRESS RINSE Press the maintenance key (7). CLEANING FILL TABLET Fill in the tablet (see Fig. 15) PRESS RINSE Press the maintenance key (7).
NO – TRAY Insert the tray again. SOLVENT IN TANK Completely dissolve the content of one blister (3 tablets) in a jug containing 0.5 litres of water, and fill the mixture in the water tank. Reinstall the water tank. OPEN TAP SOLVENT IN TANK Put a sufficiently large container under the hot water spout (Fig. 17). Open the steam / hot water draw-off valve (14) (Fig. 13). DE-SCALING CLOSE TAP Close the steam / hot water draw-off tap (14).
20. Tips for perfect coffee Height-adjustable coffee spout (17) You can adjust the height of the coffee spout to the size of your cups (Fig. 3) Grinding degree Refer to Chapter 2.5 «Adjusting the grinding gear». Preheating cups You can preheat the cups using hot water or steam. The smaller the coffee you want to draw off, the more important preheating is. Sugar and cream Stirring coffee/tea will result in heat being released.
21. Messages Cause Remedy Water tank is empty. Refill water Float defective Rinse or de-scale water tank Bean tank is empty. Refill beans Although you have refilled beans, the message still appears. Draw off a cup of coffee. The message will disappear only after you have drawn off a cup of coffee Coffee grounds container full Empty coffee grounds container Tray reinstalled too early after emptying Wait 10 sec.
22.
23. Legal information 24. Technical data These operating instructions contain all the information required for using, operating and maintaining the machine properly. Knowledge of and compliance with the specifications contained in these operating instructions is required for using the machine safely as well as for operational safety and safety during maintenance. These operating instructions cannot cover any conceivable application. The machine was designed for private household use.
Art. 67296 – 4/07 JURA Elektroapparate AG – Kaffeeweltstrasse 10 – CH-4626 Niederbuchsiten Phone +41 62 389 82 09 – Fax +41 62 389 81 37 – E-mail export@jura.com – www.jura.