IMPRESSA F7 Instructions for Use The Instructions for use has been awarded the seal of approval by the independent German Technical Inspection Agency, TÜV SÜD, due to its easy-to-understand style, its thoroughness and coverage of safety aspects.
Table of contents Your IMPRESSA F7 Control elements 4 Important information 6 Proper use....................................................................................................................................................... 6 For your safety................................................................................................................................................ 6 1 Preparing and using for the first time 10 JURA on the Internet...........................................
Table of contents 6 7 8 9 10 11 Dismantling and rinsing the professional fine foam frother................................................................35 Inserting and activating the filter..............................................................................................................36 Changing the filter....................................................................................................................................... 37 Cleaning the machine..........................
Control elements Control elements 8 9 10 11 1 2 12 13 3 14 15 4 16 17 5 6 7 1 2 3 4 5 6 7 8 9 4 Bean container with aroma preservation cover Water tank cover Water tank Power switch and mains cable (back of the machine) Coffee grounds container Drip tray Cup grille Filler funnel cover Filler funnel for ground coffee 10 11 12 13 14 15 16 17 Storage compartment cover Grinder adjustment switch Measuring spoon for ground coffee Height-adjustable hot-water nozzle Switch for hot water and steam pre
Control elements 1 2 3 4 5 Top of the machine 1 Q On/Off button 2 g Rotary Switch 3 c Maintenance button Front 4 Display 5 Preparation buttons Y Ristretto button < Espresso button > Coffee button § Hot Water button n Steam button * Cappuccino button The Connector System© permits the use of different cappuccino frothers. These are available from stockists.
Important information Important information Proper use The machine is designed and intended for private domestic use. It should only be used for coffee preparation and to heat milk and water. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use. Before using the machine read these instructions for use thoroughly and completely and comply with the instructions they contain.
Important information UU Never open and repair the machine yourself. UU Do not modify the machine in any way that is not described in these instructions for use. The machine contains live parts. If opened, there is a danger of potentially fatal injury. Repairs may only be carried out by authorised JURA service centres, using original spare parts and accessories.
Important information UU Do not put the IMPRESSA or any individual UU UU UU UU UU UU UU UU UU UU 8 parts in the dishwasher. Switch your IMPRESSA off at the power switch before any cleaning operation. Always wipe the IMPRESSA with a damp cloth rather than a wet one, and protect it from prolonged exposure to water splash. Only connect the machine to the mains voltage in accordance with the information on the rating plate. The rating plate is located on the underside of your IMPRESSA.
Important information People, including children, who UU do not have the physical, sensory or mental capabilities to use the machine safely or UU are inexperienced or lack knowledge in how to use the machine safely must be supervised by a responsible person when using it, or must be instructed in how to use it correctly. Safety when handling the CLARIS Blue filter cartridge: UU Filter cartridges should be kept out of the reach of children. UU Store filter cartridges in a dry place in the sealed packaging.
1 1 Preparing and using for the first time Preparing and using for the first time JURA on the Internet Visit us on the Internet. You can download short operating instructions for your machine from the JURA website (www.jura.com). You will also find interesting and up-to-date information on your IMPRESSA and on every aspect of coffee. Setting up the machine When setting up your IMPRESSA, please note the following: Place the IMPRESSA on a horizontal surface that is not sensitive to water.
1 Preparing and using for the first time Precondition: The bean container has been filled. T Insert the mains plug into a power socket. 3 T Switch on the IMPRESSA using the power switch on the back of the machine. Q T Press the On/Off button to switch the IMPRESSA on. SPRACHE DEUTSCH appears on the display. g T Turn the Rotary Switch until the required language is displayed, e.g. LANGUAGE ENGLISH. k T Press the Rotary Switch to confirm the language.
1 Preparing and using for the first time T Place a receptacle (at least 300 ml) under the fine foam frother and the coffee spout. j T Turn the switch to the m position. FILTER RINSING, water flows out of the fine foam frother. EE You can interrupt rinsing of the filter at any time. To do this, turn the switch clockwise. Turn the switch anticlockwise to continue rinsing the filter. EE The water may be slightly discoloured. This is not harmful to health and does not affect the taste.
1 Preparing and using for the first time T Fill the water tank with fresh, cold water and reinsert the tank. SWITCH OPEN The arrow on the switch lights up. T Place a receptacle under the fine foam frother and under the coffee spout. j T Turn the switch to the m position. SYSTEM FILLING, the system fills up with water. SWITCH CLOSE h T Turn the switch to the ° position. The illuminated arrow on the switch goes out. SYSTEM FILLING, the system fills up with water. HEATING, the machine heats up.
1 Preparing and using for the first time Adjusting the grinder CAUTION You can adjust the grinder on a continuous scale to suit the degree of roast of your coffee. If you adjust the consistency of grind when the grinder is not operating, the grinder adjustment switch could be damaged. T Only adjust the consistency of grind when the grinder is running. The consistency of grind is correct if the coffee flows regularly from the coffee spout. In addition a fine, thick crema forms.
2 2 Preparation Preparation EE You can stop the machine at any time while a speciality coffee, steam or hot water is being prepared. Just press any button (for a speciality coffee) or return the switch to its original position (for steam and hot water). EE Before the grinding operation you can select the coffee strength by turning the Rotary Switch g: MILD, NORMAL, STRONG or EXTRA. EE During the grinding operation you can select the coffee strength of single products by turning the Rotary Switch g.
2 Preparation Two speciality coffees at the touch of a button Two ristretti, two espressi or two coffees can always be prepared following the same model: Press the preparation button you want twice within two seconds. Cappuccino Your IMPRESSA can prepare a cappuccino without the cup having to be moved. EE This chapter applies to the professional fine foam frother and the fine foam frother. Example: Proceed as follows to prepare one cappuccino. Precondition: READY is displayed.
2 Preparation h T Turn the switch to the ° position. The illuminated arrow on the switch goes out. CAPPUCCINO appears on the display. Coffee preparation starts. The preset amount of water for espresso flows into the cup. Preparation stops automatically. READY appears on the display. To ensure that the fine foam frother always works properly, you must clean it daily when you have been preparing milk (see Chapter 5 ‘Maintenance – Cleaning the fine foam frother’).
2 Preparation j T Turn the switch to the m position. STEAM, the milk foam is prepared. Preparation stops automatically when the preset amount of steam is reached. SWITCH CLOSE h T Turn the switch to the ° position. The illuminated arrow on the switch goes out. READY / STEAM appears on the display. EE You can continue to prepare steam for the next 40 seconds or so without the machine having to heat up again.
2 Preparation T Open the cover of the filler funnel for ground coffee. FILL PRE-GROUND T Place one level measuring spoon of ground coffee into the filler funnel. T Close the cover of the filler funnel. SELECT BUTTON < T Press the Espresso button. Preparation starts. 1 ESPRESSO, the preset amount of water for espresso flows into the cup. Preparation stops automatically. READY appears on the display.
2 Preparation EE You can also permanently set the amount of water for all speciality coffees and hot water in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Product settings’). Hot water To obtain a perfect water flow, use the hot-water nozzle. You can find the hot-water nozzle under the cover of the storage compartment. J CAUTION There is a danger of scalding from hot water splashes. T Avoid direct contact with the skin. Example: Proceed as follows to prepare hot water.
3 3 Daily operation Daily operation Switching on Daily maintenance of the machine and hygiene when handling milk, coffee and water are key to a perfect coffee result in the cup every time. You should therefore change the water daily. Precondition: Your IMPRESSA is switched on at the power switch. T Place a receptacle under the coffee spout. Q T Press the On/Off button to switch the IMPRESSA on. HEATING RINSING, the system is rinsed. The rinse stops automatically. READY appears on the display.
3 Daily operation Switching off When the IMPRESSA is switched off, the system is automatically rinsed if a speciality coffee has been prepared. If cappuccino or milk foam has been prepared, the machine will also prompt you to rinse the cappuccino frother. Precondition: READY is displayed. T Place a receptacle under the fine foam frother and under the coffee spout. Q T Press the On/Off button. SWITCH OPEN (if you have prepared cappuccino or milk foam) The arrow on the switch lights up.
4 4 Permanent settings in programming mode Permanent settings in programming mode You can make permanent settings in programming mode. You can navigate through the programme items and permanently save the required settings simply by turning and pressing the Rotary Switch. You can make the following settings with the Rotary Switch: Programme item Sub-item Explanation RINSE C CLEANING, RINSE, C RINSE, CLEAN, FILTER (only if filter T Start the required maintenance programme here.
4 Permanent settings in programming mode Programme item Sub-item Explanation INFO COUNTER, T Keep track of all products prepared and view CLEAN, the number of maintenance programmes DESCALE (only if filter performed and the maintenance status. is not activated), FILTER (only if filter is activated), VERSION ML, OZ DISPLAY T Select the unit for the amount of water. LANGUAGE T Select your language. EXIT T Exit programming mode.
4 Permanent settings in programming mode g T Turn the Rotary Switch until BUTTONS is displayed. k T Press the Rotary Switch to enter the programme item. SELECT BUTTON EE Next select the button of the product for which you would like to make settings. No product is prepared at this point. EE To change the setting for a double product, press the corresponding symbol twice within 2 seconds. > T Press the Coffee button. 1 COFFEE appears briefly on the display.
4 Permanent settings in programming mode k T Press the Rotary Switch to enter the programme item. 16 °dH g T Turn the Rotary Switch until 25 °dH is displayed. k T Press the Rotary Switch to confirm the setting. OK appears briefly on the display. HARDNESS g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode. READY Energy-saving mode The energy-saving mode (Energy Save Mode, E.S.M.
4 Automatic switch-off Permanent settings in programming mode By instructing your IMPRESSA to automatically switch itself off, you can cut down your energy consumption. If this function is activated, your IMPRESSA switches off automatically after the preset time following the last action on the machine. You can set the automatic switch-off to 15 minutes, 30 minutes or 1–15 hours. Example: Proceed as follows to change the switch-off time from 2 HRS. to 1 HRS.. Precondition: READY is displayed.
4 Permanent settings in programming mode Precondition: READY is displayed. k T Press and hold the Rotary Switch until RINSE appears. g T Turn the Rotary Switch until RINSES is displayed. k T Press the Rotary Switch to enter the programme item. INIT RINSE g T Turn the Rotary Switch until C-RINSE is displayed. k T Press the Rotary Switch to enter the programme item. AFTER 10' g T Turn the Rotary Switch until NOW is displayed. k T Press the Rotary Switch to confirm the setting.
4 Permanent settings in programming mode k T Press the Rotary Switch to enter the programme item. PRODUCT k T Press the Rotary Switch. SELECT BUTTON < T Press the Espresso button. OK appears briefly on the display. PRODUCT g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit the programme item. RESET ALL g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.
4 Permanent settings in programming mode EE The maintenance status can also be displayed in addition to the number of performed maintenance programmes. The bar shows the current maintenance status. When the bar is completely filled, your IMPRESSA will request the respective maintenance programme. k T Press the Rotary Switch to exit the programme item. COUNTER EE Turn the Rotary Switch g to view additional information. g T Turn the Rotary Switch until EXIT is displayed.
4 Language Permanent settings in programming mode In the programme item LANGUAGE you can select the language used by your IMPRESSA. Example: Proceed as follows to change the language from ENGLISH to DEUTSCH. Precondition: READY is displayed. k T Press and hold the Rotary Switch until RINSE appears. g T Turn the Rotary Switch until LANGUAGE is displayed. k T Press the Rotary Switch to enter the programme item. LANGUAGE ENGLISH g T Turn the Rotary Switch until DEUTSCH is displayed.
5 5 Maintenance Maintenance Your IMPRESSA has the following integrated maintenance programmes: Rinsing the machine (RINSE) Rinsing the fine foam frother (C RINSE) Cleaning the fine foam frother (C CLEANING) Changing the filter (FILTER) Cleaning the machine (CLEAN) Descaling the machine (DESCALE) (only if filter is not activated) UU UU UU UU UU UU EE Clean the machine, change the filter or descale the machine when you are prompted to do so.
5 Rinsing the fine foam frother Maintenance EE This chapter applies to the professional fine foam frother and the fine foam frother. After each milk preparation, the IMPRESSA prompts you to perform a cappuccino rinse. Precondition: RINSE CAPPUCCINO is displayed and the Maintenance button c lights up. T Place a receptacle under the fine foam frother. c T Press the Maintenance button. SWITCH OPEN The arrow on the switch lights up. j T Turn the switch to the m position.
5 Maintenance T Remove the milk pipe from the milk container or carton. T Pour 250 ml of fresh water into a receptacle and add one capful of Cappuccino Cleaner. T Immerse the milk pipe in the receptacle. T Place a receptacle under the fine foam frother. k T Press the Rotary Switch. HEATING / STEAM As soon as the machine has heated up, SWITCH OPEN appears. The arrow on the switch lights up. j T Turn the switch to the m position. CAPPUCCINO CLEANING, the fine foam frother and the milk pipe are cleaned.
5 Maintenance T Dismantle the fine foam frother into its individual parts. T Rinse all the parts of the fine foam frother thoroughly under running water. If there are severely dried-on milk residues, firstly immerse the individual parts in JURA Cappuccino Cleaner and then rinse them thoroughly. T Re-assemble the fine foam frother. EE Ensure that all individual parts are correctly and firmly connected to ensure optimum operation. T Firmly attach the fine foam frother to the Connector System©.
5 Maintenance Inserting and activating the filter Your IMPRESSA no longer has to be descaled if you are using the CLARIS Blue filter cartridge. If you did not activate the filter cartridge the first time you used the machine, you can do this now as follows. EE Perform the ‘inserting the filter’ operation without any interruptions. This will ensure that your IMPRESSA always produces its best. Precondition: READY is displayed. k T Press and hold the Rotary Switch until RINSE appears.
5 Maintenance EE You can interrupt rinsing of the filter at any time. To do this, turn the switch clockwise. Turn the switch anticlockwise to continue rinsing the filter. EE The water may be slightly discoloured. This is not harmful to health and does not affect the taste. Rinsing of the filter stops automatically after approximately 300 ml. SWITCH CLOSE appears on the display. h T Turn the switch to the ° position. The illuminated arrow on the switch goes out. HEATING, the machine heats up.
5 Maintenance T Place a receptacle (at least 300 ml) under the fine foam frother. k T Press the Rotary Switch. SWITCH OPEN The arrow on the switch lights up. j T Turn the switch to the m position. FILTER RINSING, water flows out of the fine foam frother. EE You can interrupt rinsing of the filter at any time. To do this, turn the switch clockwise. Turn the switch anticlockwise to continue rinsing the filter. EE The water may be slightly discoloured.
5 c c Maintenance T Empty the drip tray and coffee grounds container and put them back into the machine. PRESS RINSE, the Maintenance button c lights up. T Place a receptacle under the coffee spout. T Press the Maintenance button. CLEANING, water flows out of the coffee spout. The operation is interrupted, ADD TABLET. T Open the cover of the filler funnel for ground coffee. T Insert a JURA cleaning tablet into the filler funnel. T Close the cover of the filler funnel.
5 Maintenance CAUTION If the descaling operation is interrupted, there may be damage to the machine. T Allow the descaling programme to run to the end. CAUTION If the descaling agent comes into contact with sensitive surfaces (e.g. marble), damage cannot be ruled out. T Clean up any splashes immediately. EE The descaling programme lasts approximately 45 minutes. EE JURA descaling tablets are available from specialised dealers.
5 Maintenance h T Turn the switch to the ° position. DESCALING, the descaling operation is continued. The Maintenance button c flashes during the descaling operation. The operation is interrupted, EMPTY TRAY. T Empty the drip tray and coffee grounds container and put them back into the machine. FILL WATER TANK T Empty the receptacle and place it under the Connector System© and the coffee spout. T Remove the water tank and rinse it thoroughly.
5 Maintenance Cleaning the bean container Coffee beans may be covered with a slight oil film which remains on the walls of the bean container. These traces may negatively affect the coffee result. For this reason clean the bean container from time to time. Precondition: FILL BEANS is displayed. Q T Switch the machine off with the On/Off button. 3 T Switch the machine off at the power switch. T Remove the aroma preservation cover. T Clean the bean container with a soft, dry cloth.
6 6 Display messages Display messages Message Cause/Result The water tank is empty. You cannot prepare any products. Action EMPTY GROUNDS The coffee grounds container is full. You cannot prepare any products. T Empty the coffee grounds container and the drip tray (see Chapter 3 ‘Daily operation – Daily maintenance’). TRAY MISSING The drip tray is not inserted correctly or is not inserted at all. You cannot prepare any products. The bean container is empty. You cannot prepare any products.
7 Troubleshooting 7 Troubleshooting Problem Insufficient foam is produced when the milk is frothed or milk sprays out of the fine foam frother. Cause/Result The fine foam frother is dirty. Action Coffee only comes out in drips when it is being prepared. T Put the grinder on a coarser setting or use coarser ground coffee (see Chapter 1 ‘Preparing and using for the first time – Adjusting the grinder’). T Perform descaling (see Chapter 5 ‘Maintenance – Descaling the machine’).
7 Problem ERROR 2 or ERROR 5 is displayed. Other ERROR messages are displayed. Cause/Result If the machine has been exposed to the cold for a long period of time, heating may be disabled for safety reasons. – Troubleshooting Action T Warm the machine at room temperature. T Switch the IMPRESSA off at the power switch. Contact customer support in your country (see Chapter 11 ‘JURA contact details / Legal information’).
8 8 Transport and environmentally friendly disposal Transport and environmentally friendly disposal Transport / Emptying the system Keep the packaging for your IMPRESSA. It should be used to protect the machine during transport. In order to protect the IMPRESSA from frost during transport, the system must be emptied. Precondition: READY is displayed. T Place a receptacle under the fine foam frother. n T Press the Steam button. HEATING / STEAM As soon as the machine has heated up, READY / STEAM appears.
9 9 Technical data Technical data Voltage Power Conformity mark Energy consumption 220–240 V ~, 50 Hz 1450 W AS approx. 6 Wh ENERGY w Energy consumption approx. 13 Wh ENERGY Pump pressure Holding capacity of water tank Holding capacity of bean container Holding capacity of coffee grounds container Cable length Weight Dimensions (W × H × D) Static, max. 15 bar 1.9 l 310 g Max. 15 portions approx. 1.1 m 9.6 kg 28.5 × 35.5 × 44.
10 Index 10 A B C Index Contact details 52 Cover Filler funnel for ground coffee 4 Storage compartment 4 Water tank 4 Cup grille 4 Customer support 52 Addresses 52 Aroma preservation cover Bean container with aroma preservation cover 4 Automatic switch-off 27 Bean container Bean container with aroma preservation cover 4 Cleaning 42 Filling 10 Bus bar Technical data 47 Button Cappuccino button 5 Coffee button 5 Espresso button 5 Hot Water button 5 Maintenance button 5 On/Off button 5 Ristretto button 5
10 G H I J L M Grinder adjustment switch 4 Ground coffee 18 Measuring spoon for ground coffee 4 Grounding point 47 P Height-adjustable coffee spout 4 Hotline 52 Hot water 20 Hot water and steam preparation Switch for hot water and steam preparation 4 Hot-water nozzle 4 Instant coffee Ground coffee 18 Internet 10 JURA Contact details 52 Internet 10 Language 31 Machine Cleaning 38 Descaling 39 Rinsing 32 Setting up 10 Switching off 22 Switching on 21 Mains cable 4 Maintenance 32 Daily maintenance 21 M
10 S T U Index Safety 6 Safety information 6 Settings Permanent settings in programming mode 23 Setting up Setting up the machine 10 Short operating instructions 10 Switch for hot water and steam preparation 4 Switching off Machine 22 Switching on Machine 21 Switch-off Automatic switch-off 27 Switch-on rinse 27 Symbol description 3 Technical data 47 Tel 52 Transport 46 Troubleshooting 44 Two products 16 Unit for amount of water 30 Use, First-time 10 W Water hardness Determining the water hardness 13
Art. 70554/F7/en/201308 11 11 JURA contact details / Legal information JURA contact details / Legal information JURA Elektroapparate AG Kaffeeweltstrasse 10 CH-4626 Niederbuchsiten Tel. +41 (0)62 38 98 233 @@ You will find additional contact details for your country at www.jura.com.
