IMPRESSA J9.2 One Touch Instructions for Use The Instructions for Use has been awarded the seal of approval by the independent German Technical Inspection Agency, TÜV SÜD, due to its easy-to-understand style, its thoroughness and coverage of safety aspects.
Table of contents Your IMPRESSA J9.2 One Touch Control elements 4 Important information 6 Proper use ...................................................................................................................................................... 6 For your safety ............................................................................................................................................... 6 1 Preparing and using for the first time 9 JURA on the Internet ...............................
Table of contents 5 6 7 8 9 10 11 Maintenance 31 Rinsing the machine ....................................................................................................................................31 Rinsing the cappuccino frother ................................................................................................................ 32 Cleaning the cappuccino frother ..............................................................................................................
Control elements Control elements 1 2 3 4 5 6 7 8 4 Bean container cover Water tank cover Bean container with aroma preservation cover Water tank Height-adjustable cappuccino frother Coffee grounds container Drip tray Cup platform 9 10 11 12 13 14 15 Filler funnel for ground coffee Storage compartment cover Grinder adjustment switch Hot-water nozzle Measuring spoon for ground coffee Height- and width-adjustable coffee spout Power switch and mains cable (side of mac
Control elements Surface of the machine 1 Q On/Off button 2 g Rotary Switch 3 c Maintenance button Front 4 Display 5 Preparation buttons u Ristretto button i Espresso button o Coffee button m Hot Water button z Milk button q Latte Macchiato button p Cappuccino button 5
Important information Important information Proper use The machine is designed and intended for private domestic use. It should only be used for coffee preparation and to heat milk and water. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use. Before using the machine read these instructions for use thoroughly and completely and comply with the instructions they contain.
Important information U To completely and safely disconnect the machine from the power supply, first switch off the IMPRESSA using the On/Off button and then at the power switch. Only then should you remove the mains plug from the power socket. There is a risk of scalds or burns on the spouts and the cappuccino frother. Place the machine out of the reach of children. Do not touch any hot parts. Use the handles provided. Ensure that the cappuccino frother is correctly fitted and clean.
Important information U U Only fill the water tank with fresh, cold water. Switch the machine off at the power switch if you are going to be absent for a longer period of time. People, including children, who do not have the physical, sensory or mental capabilities to use the machine safely or are inexperienced or lack knowledge in how to use the machine safely must be supervised by a responsible person when using it, or must be instructed in how to use it correctly.
1 1 Preparing and using for the first time Preparing and using for the first time JURA on the Internet Visit us on the Internet. @ You can download short operating instructions for your machine from the JURA website (www.jura.com). You will also find interesting and up-to-date information on your IMPRESSA and on every aspect of coffee. Setting up the machine When setting up your IMPRESSA, please note the following: Place the IMPRESSA on a horizontal surface that is not sensitive to water.
1 Preparing and using for the first time T Fill the bean container with coffee beans, then close the aroma preservation cover and the bean container cover. First-time use J WARNING If the machine is operated with a defective mains cable, there is a danger of potentially fatal electric shock. T Never use a machine which is damaged or has a defective mains cable. Precondition: The water tank and bean container are full. T Insert the mains plug into a power socket.
1 Inserting and activating the filter Preparing and using for the first time Your IMPRESSA no longer has to be descaled if you are using the CLARIS Blue filter cartridge. E Perform the ‘inserting the filter’ operation without any interruptions. This will ensure that your IMPRESSA always produces its best. Precondition: COFFEE READY is displayed. k T Press and hold the Rotary Switch until MAINTENANCE appears on the display. g T Turn the Rotary Switch until FILTER NO is displayed.
1 Preparing and using for the first time E The water may be slightly discoloured. This is not harmful to health and does not affect the taste. Rinsing of the filter stops automatically after approximately 500 ml. The machine heats up. COFFEE READY appears on the display. The filter is activated. Determining and adjusting the water hardness E If you are using the CLARIS Blue filter cartridge and have activated it in programming mode, you will not be able to adjust the water hardness.
1 Preparing and using for the first time k T Press the Rotary Switch to enter the programme item. 16°dH n n n k k g T Turn the Rotary Switch until 25°dH n n n n n is displayed. k T Press the Rotary Switch to confirm the setting. CONFIRMED appears briefly on the display. HARDNESS 25°dH g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode. COFFEE READY appears on the display.
2 Preparation 2 Preparation E You can stop preparation of a speciality coffee, milk speciality or hot water at any time. Just press any button. E Before and during the grinding operation you can select the coffee strength of individual products: extra-mild (ö), mild (öö), normal (ööö), strong (öööö) or extra-strong (ööööö). E During preparation, you can change the preset amount of water by turning the Rotary Switch. E You can follow the current status of preparation on the progress bar.
2 Preparation Latte macchiato, cappuccino Your IMPRESSA can prepare a latte macchiato or cappuccino at the touch of a button. There is no need to move the glass or cup. Example: Proceed as follows to prepare one latte macchiato. T Remove the protective cover from the cappuccino frother. T Attach the milk pipe to the cappuccino frother. Use the long pipe for a milk carton and the short pipe for a milk container. T Insert the other end of the milk pipe into a milk carton or connect it to a milk container.
2 Preparation Warm milk and milk foam Example: Proceed as follows to prepare milk foam. T Remove the protective cover from the cappuccino frother. T Attach the milk pipe to the cappuccino frother. Use the long pipe for a milk carton and the short pipe for a milk container. T Insert the other end of the milk pipe into a milk carton or connect it to a milk container. T Place a cup under the cappuccino frother. T Turn the setting wheel of the cappuccino frother to the Milk Foam position ü.
2 Preparation Ground coffee You can choose to use a second coffee variety, for example decaffeinated coffee, with the filter funnel for ground coffee. E Never add more than two level measuring spoons of ground coffee. E Use ground coffee which is not ground too finely. Very fine coffee can block up the system so that the coffee only comes out in drips. E If you did not fill the machine with a sufficient amount of ground coffee, NOT ENOUGH PRE-GROUND is displayed and the IMPRESSA stops the operation.
2 Preparation Permanently setting the amount of water for the cup size It is easy to make permanent settings for the amount of water for all speciality coffees and hot water according to the cup size. Adjust the amount once as shown in the following example. Every time you prepare a drink in the future, this amount of water will be dispensed. The permanent settings for adapting the amount of water to the cup size for all speciality coffees and hot water follow this model.
2 Preparation Hot water To obtain a perfect water flow, use the hot-water nozzle. You can find the hot-water nozzle under the cover of the storage compartment. The following temperatures can be selected for preparing hot water: LOW, NORMAL, X HIGH. J CAUTION There is a danger of scalding from hot water splashes. T Avoid direct contact with the skin. T Carefully pull the cappuccino frother down and off. T Open the storage compartment cover, take out the hotwater nozzle and close the cover again.
3 3 Daily operation Daily operation Switching on When the IMPRESSA is switched on, it automatically prompts you to perform the rinse operation. Start the rinse operation by pressing the Maintenance button c. In programming mode you can change this setting so that the machine starts the switch-on rinse automatically (see Chapter 4 ‘Permanent settings in programming mode – Rinses’). Precondition: Your IMPRESSA is switched on at the power switch. T Place a receptacle under the coffee spout.
3 Switching off Daily operation When you switch your IMPRESSA off, the spouts used to prepare a speciality coffee or milk are rinsed. T Place one receptacle under the coffee spout and another under the cappuccino frother. Q T Press the On/Off button. MACHINE RINSING, the spouts used to prepare a speciality coffee or milk are rinsed. The operation stops automatically and your IMPRESSA is switched off. E When the IMPRESSA is switched off with the On/Off button, the machine consumes less than 0.
4 Permanent settings in programming mode 4 Permanent settings in programming mode You can make permanent settings in programming mode. You can navigate through the programme items and permanently save the required settings simply by turning and pressing the Rotary Switch.
4 Permanent settings in programming mode Programme item Sub-item Explanation SYMBOL BRIGHTNESS LANGUAGE BRIGHTNESS T Adjust the brightness of the symbols. T Select your language. T Exit programming mode. EXIT Products In the programme item PRODUCTS you can make individual settings for all speciality coffees and hot water.
4 Permanent settings in programming mode g T Turn the Rotary Switch until PRODUCTS is displayed. k T Press the Rotary Switch to enter the programme item. SELECT PRODUCT E Next select the button of the product for which you would like to make settings. No product is prepared at this point. E To change the setting for a double product, press the corresponding symbol twice within 2 seconds. q T Press the Latte Macchiato button. COFFEE 45 ML k T Press the Rotary Switch to enter the programme item.
4 Permanent settings in programming mode k T Press the Rotary Switch to exit the programme item. COFFEE READY Energy-saving mode In the programme item ECONOMY MODE you can permanently set an energy-saving mode (Energy Save Mode, E.S.M.©): U SAVE NO U All speciality coffees, speciality coffees with milk and hot water can be prepared without having to wait. U U Before milk preparation, the machine heats up.
4 Permanent settings in programming mode Automatic switch-off By instructing your IMPRESSA to automatically switch itself off, you can cut down your energy consumption. If this function is activated, your IMPRESSA switches off automatically after the preset time following the last action on the machine. You can set the automatic switch-off time to 15 minutes or 0.5–15 hours. Example: Proceed as follows to change the automatic switch-off from 2 H to 15 MIN.. Precondition: COFFEE READY is displayed.
4 Permanent settings in programming mode Example: Proceed as follows to make the machine prompt you to perform the cappuccino rinse immediately after preparing a speciality coffee with milk. Precondition: COFFEE READY is displayed. k T Press and hold the Rotary Switch until MAINTENANCE appears. g T Turn the Rotary Switch until RINSES is displayed. k T Press the Rotary Switch to enter the programme item. INIT RINSE MANUAL g T Turn the Rotary Switch until CAPP RINSE AFTER 10' is displayed.
4 Permanent settings in programming mode Example: Proceed as follows to reset the values for ‘Espresso’ to the factory settings. Precondition: COFFEE READY is displayed. k T Press and hold the Rotary Switch until MAINTENANCE appears. g T Turn the Rotary Switch until RESET is displayed. k T Press the Rotary Switch to enter the programme item. PRODUCT i T Press the Espresso button. CONFIRMED appears briefly on the display. The settings for ‘Espresso’ are reset to the factory settings.
4 Permanent settings in programming mode E The maintenance status can also be displayed in addition to the number of performed maintenance programmes. The bar shows the current maintenance status. When the bar is completely filled, your IMPRESSA will request the respective maintenance programme. k T Press the Rotary Switch to exit the programme item. INFORMATION g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.
4 Permanent settings in programming mode g T Turn the Rotary Switch to set the required brightness of the symbols. k T Press the Rotary Switch to confirm the setting. CONFIRMED appears briefly on the display. SYMBOL BRIGHTNESS g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode. COFFEE READY Language In this programme item you can set the language used by your IMPRESSA. Example: Proceed as follows to change the language from ENGLISH to DEUTSCH.
5 5 Maintenance Maintenance Your IMPRESSA has the following integrated maintenance programmes: Cleaning the cappuccino frother (CLEAN CAPPUCCINO) Rinsing the cappuccino frother (RINSE CAPPUCCINO) Changing the filter (CHANGE FILTER) Cleaning the machine (CLEAN MACHINE) Rinsing the machine (RINSE MACHINE) Descaling the machine (DECALCIFY MACHINE) U U U U U U E Clean or descale the machine or change the filter when the display prompts you to do so.
5 Maintenance Rinsing the cappuccino frother After each milk preparation, the IMPRESSA prompts you to run a cappuccino rinse. Precondition: COFFEE READY / RINSE CAPPUCCINO is displayed and the Maintenance button c lights up. T Place a receptacle under the cappuccino frother. c T Press the Maintenance button. CAPPU. RINSING, the cappuccino frother is rinsed. The operation stops automatically and COFFEE READY appears on the display.
5 c Maintenance T Place another receptacle under the cappuccino frother. T Press the Maintenance button. CAPPUCCINO CLEANS, the cappuccino frother and the pipe are cleaned. WATER FOR CAPPUCCINO c Dismantling and rinsing the cappuccino frother T Rinse the receptacle thoroughly, fill it with 250 ml of fresh water and immerse the milk pipe in the water. T Empty the other receptacle and place it under the cappuccino frother again. T Press the Maintenance button.
5 Maintenance Precondition: COFFEE READY / CHANGE FILTER is displayed and the Maintenance button c lights up. c T Press the Maintenance button. DURATION 2 MIN. / START YES E If you do not want to start changing the filter just yet, turn the Rotary Switch until START NO is displayed. Press the Rotary Switch to exit the maintenance programme. The prompt to ‘change the filter’ remains active. c c T Press the Maintenance button. CHANGE FILTER / PRESS RINSE T Remove and empty the water tank.
5 Cleaning the machine CAUTION Maintenance After 200 preparations or 80 switch-on rinses, the IMPRESSA will prompt you to clean it. If the wrong cleaning agent is used, the machine could be damaged and/or traces could be left behind in the water. T Use only original JURA maintenance products. E The cleaning programme lasts approximately 20 minutes. E Do not interrupt the cleaning programme. The quality of cleaning will be impaired if you do so. E JURA cleaning tablets are available from stockists.
5 Maintenance c Descaling the machine T Insert a JURA cleaning tablet into the filler funnel. T Close the cover of the filler funnel. ADD TABLET / PRESS RINSE, the Maintenance button c lights up. T Press the Maintenance button. CLEANS, water flows repeatedly out of the coffee spout and the cappuccino frother. The operation is interrupted, EMPTY TRAY. T Empty the drip tray and coffee grounds container and put them back into the machine. Cleaning is now complete.
5 Maintenance Precondition: COFFEE READY / DECALCIFY MACHINE is displayed and the Maintenance button c lights up. c T Press the Maintenance button. DURATION 45 MIN. / START YES E If you do not want to start descaling just yet, turn the Rotary Switch until START NO is displayed. Press the Rotary Switch to exit the maintenance programme. The prompt to ‘descale the machine’ remains active. c T Press the Maintenance button.
5 Maintenance c T Fill the water tank with fresh, cold water and reinsert the tank. PRESS RINSE, the Maintenance button c lights up. T Refit the cappuccino frother. T Place a receptacle under the cappuccino frother and another under the coffee spout. T Press the Maintenance button. DECALCS, water flows out of the cappuccino frother and the coffee spout. HEATING UP, MACHINE RINSING, water flows out of the coffee spout. The operation stops automatically, EMPTY TRAY.
5 Descaling the water tank Maintenance Limescale deposits may form in the water tank. To ensure correct function of the machine, descale the water tank from time to time. T Remove the water tank. T If you use a CLARIS Blue filter cartridge, remove this. T Descale the tank with a mild conventional descaling agent in accordance with the manufacturer's instructions. T Rinse out the water tank thoroughly. T If you use a CLARIS Blue filter cartridge, insert this again.
6 Display messages 6 Display messages Message Cause/Result Action FILL WATER TANK The water tank is empty. You cannot prepare any products. T Fill the water tank (see Chapter 1 ‘Preparing and using for the first time – Filling the water tank’). EMPTY GROUNDS The coffee grounds container is full. You cannot prepare any speciality coffees, but you can prepare hot water and milk. T Empty the coffee grounds container and the drip tray (see Chapter 3 ‘Daily operation – Daily maintenance’).
6 Display messages Message Cause/Result Action COFFEE READY / DECALCIFY MACHINE or COFFEE READY / DECALCIFY NOW COFFEE READY / CHANGE FILTER or COFFEE READY / CHANGE NOW The IMPRESSA is prompting you to descale it. T Perform descaling (see Chapter 5 ‘Maintenance – Descaling the machine ’). The filter cartridge no longer works. T Replace the CLARIS Blue filter cartridge (see Chapter 5 ‘Maintenance – Changing the filter’).
7 Troubleshooting 7 Troubleshooting Problem Cause/Result Action T Turn the setting wheel of the cappuccino to the far right and the Milk Foam position ü. T Change the length of the interval to at least 30 seconds (see Chapter 4 ‘Permanent settings in programming mode – Products’) in the programming mode. When preparing a latte macchiato, the typical three layers do not form. – Insufficient foam is produced when the milk is frothed or milk sprays from the cappuccino frother.
7 Troubleshooting Problem Cause/Result Action Little or no water or steam comes out of the cappuccino frother. The pump is very quiet. The connector of the cappuccino frother may be blocked by milk residues or limescale fragments loosened during descaling. T Remove the cappuccino frother. T Unscrew the black connector with the aid of the hexagonal hole on the measuring spoon for ground coffee. T Clean the connector thoroughly. T Screw the connector back on by hand.
8 8 Transport and environmentally friendly disposal Transport and environmentally friendly disposal Transport / Emptying the system In order to protect the IMPRESSA from frost during transport, the system must be emptied. Precondition: COFFEE READY is displayed. T Carefully pull the cappuccino frother down and off. T Place a receptacle under the connector of the cappuccino frother. z T Press the Milk button. HEATING UP As soon as the machine has heated up, COFFEE READY appears.
9 Technical data 9 Technical data Voltage 220–240 V ~, 50 Hz Power 1450 W Safety test S Energy consumption SAVE YES Approx. 5 Wh Energy consumption SAVE NO Approx. 12 Wh Pump pressure Static, max. 15 bar Holding capacity of water tank 2.1 l Holding capacity of bean container 250 g Holding capacity of coffee grounds container Max. 16 portions Cable length Approx. 1.1 m Weight 10.9 kg Dimensions (W × H × D) 28.5 × 34.2 × 43.
10 Index 10 Index Cover Bean container 4 Cup platform 4 Customer support 48 A Addresses 48 Automatic switch-off 26 B Bean container Bean container with aroma preservation cover 4 Cleaning 38 Filling 9 Bus bar Technical data 45 Button Cappuccino button 5 Coffee button 5 Espresso button 5 Hot Water button 5 Latte Macchiato button 5 Maintenance button 5 Milk button 5 On/Off button 5 Ristretto button 5 D Degree of water hardness 12 Descaling Machine 36 Water tank 39 Determining and adjusting the water har
10 Programming mode 22 Automatic switch-off 26 Brightness of symbols 29 Energy-saving mode 25 Language 30 Products 23 Restore factory settings 27 Rinses 26 Unit for amount of water 29 Proper use 6 I Instant coffee Ground coffee 16 Internet 9 J JURA Contact details 48 Internet 9 L Language 30 Latte macchiato 15 R Rinses 26 Rinsing Cappuccino frother 32 Machine 31 Ristretto 14 Rotary Switch 5 M Machine Cleaning 35 Descaling 36 Rinsing 31 Setting up 9 Switching off 21 Switching on 20 Mains cable 4 Mainte
Art. 69422/J9.2/en/201009 11 JURA contact details / Legal information 11 JURA contact details / Legal information JURA Elektroapparate AG Kaffeeweltstrasse 10 CH-4626 Niederbuchsiten Tel. +41 (0)62 38 98 233 @ You will find additional contact details for your country at www.jura.com.
