IMPRESSA S85 Art. Nr.
Legend: DISPLAY: serves as information. DISPLAY: please follow the instructions shown. = Note = Important = Tip JURA Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www.jura.
Fig. 1 Fig. 2 Fig. 3 Fig. 4 A Fig. 5 Fig. 6 Fig. 7 B Fig. 8 2 1 3 Fig. 9 Fig. 10 Fig. 11 Fig.
12 13 14 15 16 11 17 10 9 8 7 6 5 4 18 3 2 1 D E C F B G A H 19 20 21 22
Operating elements JURA Impressa S85 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Drip tray / residual water container Drip tray cover Cover for programming keys Coffee key for 2 normal cups Coffee key for 1 normal cup Coffee key for 2 small cups Coffee key for 1 small cup Key for special coffee ON/OFF switch Rinsing key Display dialogue system Water tank with carrying handle Cover for bean container and aroma protection lid Cover for pre-ground coffee filler funnel Height-adjustable coffee-spo
Table of contents JURA Impressa S85 1. Description ...................................................page 2. Safety instructions .........................................page 2.1 Warnings ............................................page 2.2 Safety precautions .................................page 3. Check before use............................................page 3.1 Checking mains voltage ..........................page 3.2 Checking fuse .......................................page 3.3 Adding coffee beans .
Important information for the user 2. Safety instructions Thank you for choosing this JURA product. 2.1 Warnings Please study these instructions carefully before using your new machine and keep them in a safe place for easy reference in the future.
If using acidic decalcifying agents be sure to immediately remove any splashes and drops from delicate surfaces, especially natural stone and wooden surfaces, or take corresponding precautions. 3. Check before use 3.1 Checking mains voltage The machine is set for the correct voltage before leaving our factory. Ensure that your mains voltage corresponds to the details quoted on the rating plate attached to the bottom of the machine. 3.2 Checking fuse The machine is designed for a current of 10 amps.
5. Rinsing the machine RINSE UNIT Place an empty cup under the coffee-spout (15). Press rinsing key . If the machine has been switched off and has already cooled down it will be necessary to carry out this rinsing function when the machine is switched on again. After switching off the machine, the rinsing sets off automatically. 6. Adjusting for water hardness The water is heated inside the machine. With use, this leads to calcium deposits (furring) forming on the machine.
Switch the machine on by pressing key ON/OFF. Open front cover (3) and press key P until you hear an acoustic signal. PRESS KEY / POWDER QUANTITY Press key + several times until the following message appears: FILTER NO By pressing key P you can hear an acoustic signal. NO flashes You can alter the setting by pressing key - or + . YES flashes To confirm press key P . An acoustic signal can be heard. RINSE FILTER / OPEN TAP Place a sufficiently large container (approx.
You can interrupt the flow of coffee at any time by simply pressing any of the coffee keys. To obtain a perfect head of froth adjust the coffee-spout (15) to the size of your cups (Fig. 3). 8.1 Drawing off powder coffee Open cover (3) Press selector key for pre-ground powder coffee . FILL POWDER Now put 1 or 2 level measuring spoons of pre-ground coffee into the pre-ground powder funnel (14). Put 1, respectively 2 cups under the coffee-spout and press the required key.
Immerse the frothing nozzle (21) into the milk you want to froth or into the liquid you want to heat up. Turn selector switch for coffee or hot water / steam (19) to the symbol . To draw off steam open the steam/hot water draw-off valve (19). STEAM INTAKE To stop steam-function turn selector switch for coffee or hot water / steam (19) back to the symbol . After drawing off steam immediately draw off approx. 1dl of water and clean the outside of the nozzle with a cloth.
12. Switching off machine When the machine is switched off, the rinsing program is automatically run again. Therefore place an empty container under the coffee-spout (15) and press ON/OFF key . When the rinsing water has run into the container, the machine powers down. Discard the water. 13. Programming Before leaving our factory, the machine is adjusted to enable you to obtain coffee without any additional programming.
If you wish to draw another coffee to control the water quantity, press key again otherwise press key P briefly to store water quantity in memory. You can call up the next setting by pressing key + . 13.4 Programming FILTER Please read chapter 7.1 “Placing filter”. 13.5 Programming WATER HARDNESS (only with setting FILTER NO) HARDNESS LEVEL 3 Press key P By pressing key + or - briefly you can programme the water hardness level.
13.8 Programming automatic switch on time A programming of the timer clock is necessary if an automatic switch on is needed. UNIT ON –.– Press key P . By briefly pressing key + or - you can set the hours and then confirm by pressing key P . By briefly pressing key + or - you can set the minutes and then confirm by pressing key P . You can call up the next setting by pressing key + . To switch off the automatic timer proceed as follows: Press key P Press key N UNIT ON —:— 13.
14.2 Empty grounds container Coffee grounds are collected in the grounds container. EMPTY GROUNDS If this message shows on the display no more coffee can be drawn off. It is necessary to empty the grounds container. Remove drip tray carefully as there is water in it. Do not disconnect the machine from power socket while you empty grounds. 14.3 Empty drip tray EMPTY TRAY If this message shows on the display no more coffee can be drawn off. It is necessary to empty the drip tray.
Rinse fastenings in groove (B) (Fig. 8) as well as the metal contacts (A) with hot water and some washing-up liquid. Then clean the fastenings in groove (B) as well as metal contacts with a brush. 14.9 General cleaning instructions Never use abrasive articles or corrosive chemicals to clean your machine. Wipe down the casing inside and out using a soft damp cloth. Clean the pivoting hot water / steam nozzle after every use.
16.1 Decalcifying coffee sector Remove and empty water tank. Replace empty water tank. Switch off your machine by pressing ON/OFF key. Open cover (3). Press key until you can hear an acoustic signal. EMPTY TRAY AGENT IN TANK Pour 0.6 litres of water into a container and completely dissolve the contents of a blister pack (3 tablets). Then fill the mixture into the water tank. CHOOSE SECTOR / AGENT IN TANK / PRESS CALC Turn selector switch for coffee to the symbol .
17. Disposal For correct disposal, you should return your coffee machine to your dealer, JURA service centre or JURA Elektroapparate AG. 18. Tips for a perfect coffee Height adjustable coffee-spout You can adjust the height of the coffee-spout to your cup sizes. Grinding Please refer to chapter 3.4 “Adjusting grinder”. Pre-warm cups You should warm cups in advance with hot water or steam. The smaller the quantity of coffee, the more important warming the cups is.
19. Messages Cause Action FILL WATER Water tank is empty Water level indicator in tank is jammed Tank is calcified, water level indicator is stuck Top up with water Empty tank, rinse out, fill up and replace Remove tank, decalcify, rinse well, fill up with water and replace FILL BEANS Bean container is empty Message still displayed, although beans filled Top up with beans Draw off cup of coffee.
CLEAN UNIT Cause Action You have drawn off coffee 220 times or run the rinsing program 180 times Message still displayed, although machine cleaned Clean as described in chapter 15 Run cleaning program again; this time do not add cleaning tablet UNIT CALCED COFFEE SECTOR WATER SECTOR The appropriate sector needs decalcifying CLOSE TAP Not ready to provide water or steam Switch over to coffee sector, press water or steam key and then draw off the water or steam required FAULT Various causes Ring t
20. Problems Problem Cause Action Coffee only flows in dribs – Powder too fine and drabs while drawing off – – – – Adjust grinder to a coarser grinding Run one or two rinse programs If result is no better, clean the machine as per instruction Coffee flow is stopped after pre-brewing – Not enough coffee powder in the system – Draw off one cup of coffee Grinder is extremely noisy – Foreign element in grinder – Proceed as described in chapter 14.
21. Legal information 22. Technical specifications These operating instructions contain all the information necessary for the correct use, operation and maintenance of your espresso/ coffee machine. Understanding and complying with the directions contained in these operating instructions are essential to ensure that the machine is utilised without risk and to ensure safety during operation and maintenance. These operating instructions cannot cover all the possible ways in which this machine may be used.
