User's Manual

12 OPERATOR CONVENIENCES
84
yeKciM noitcnuF
1 FFO/NOrewoP
2 FFO/NOeviecerycneuqerfFH
3 hctiwsedomnoitaludoM
4 FFO/NOTIR
5 FFO/NOTIX
6 raelctesffoTIXrotesffoTIR
7 FFO/NOycneuqerf-tilpS
8 OFVotyromeMmorfrefsnarT
9
hctiwsBOFV/AOFV:edomOFVnI
egnahcon:edomllaceRyromeMnI
0
FHmorf(eveirtersgnittestnerruC
)reviecsnart
B hctiwsedomllaceRyromeM/OFV
C esaercniycneuqerftesffoTIR/TIX
D esaercedycneuqerftesffoTIR/TIX
1
zHk1/zH01:edomWCro,BSU,BSLnI
hctiws
hctiwszHk01/zHk1:edomMAroMFnI
#
2
NOyrtneycneuqerf:edomOFVnI
rebmunlennahc:edomllaceRyromeMnI
NOyrtne
Starting Sky Command II+ operation:
After you have completed the following setups, you
can start Sky Command II+ operation. Without
programming these parameters, you cannot perform
Sky Command II+ operation.
On the TS-2000 (Transporter):
1 Select the desired HF frequency that you want to
be controlled on the main transceiver.
2 Select an open VHF frequency in FM mode for the
main transceiver and another open UHF
frequency in FM mode for the sub-receiver.
3 Press [MENU], then turn the MULTI/ CH control to
access Menu No. 62E.
4 Select T-PORTER (Transporter).
5 Press [MENU] to enter the Transporter mode.
On the TM-D700A (Commander):
1 Select the same VHF and UHF frequencies that
you selected for the TS-2000 (Transporter)
2 Access Menu 4-4 to select COMMANDER.
• “PRESS [0] KEY TO START COMMANDER!!”
appears.
3 Press [0] on the DTMF Mic of the TM-D700A to
start the Sky Command II+ operation.
CONTROL OPERATION
After setting up both the TS-2000 (Transporter) and
the TM-D700A (Commander) for Sky Command II+
operation, press Mic [0] on the Commander. While in
Sky Command mode, the Mic keys of the
Commander will function as describled below.
Each time you press a key, the Commander will
automatically enter transmit mode and send the
corresponding control command to the Transporter.
1
“FS” appears when you select 1 kHz step (LSB/ USB/ CW) or
10 kHz step (FM/ AM).
2
After pressing Mic [#], press Mic [0] to [9] to enter a frequency or
memory channel number.
When Mic [0] is pressed, the Commander shows the
current settings of the HF transceiver:
q HF frequency
w VFO: A, VFO: B,
MR: 00 ~ 99 (memory channel number)
e RIT, XIT
r OFF, –9.99 ~ +9.99
t LSB, USB, CW, FM, or AM
y SPLIT–A: VFO A is used for transmitting.
SPLIT–B: VFO B is used for transmitting.
SPLIT–M: A memory channel is used for transmitting.
u “FS” appears when Mic [
] is pressed.
Note:
◆ After pressing [MENU], you can access only Menu 4–4.
◆ The Transporter will transmit its call sign in Morse code every
10 minutes, using the 144 MHz band.
◆ The APO timer will not operate on the transceiver while the
Transporter is ON.
FHehtFFO/NOhctiwsoT
reviecsnart
ciMsserP ]1[ .
roycneuqerfehtegnahcoT
FHehtnolennahcyromem
reviecsnart
ciMsserP ]PU[ / ]NWD[ .
FHnanooiduatimsnartoT
ycneuqerf
ciMdlohdnasserP ]TTP[ ,
ehtotnikaepsneht
.enohporcim
FHnanooiduaevieceroT
ycneuqerf
ciMsserP ]2[ .
dnabFHUehtrotinomoT
rednammoCehtno
yekFPciMehtsserP
rotinoMehtdengissa
.noitcnuf
q
eyr
u
w
t