User's Manual

87
12 OPERATOR CONVENIENCES
USING ANOTHER TS-2000 AS A COMMANDER
To use another TS-2000(X) transceiver as a
“Commander” (an external remote control unit), follow
the steps below. Basically, it is the same as using a
TM-D700A as a “Commander” (described on pages
83 and 84).
TS-2000(X) (Transporter) Setup:
1 Press [MENU], then turn the MULTI/ CH control to
access Menu No. 62A.
2 Enter your callsign (ex: WD6DJY) as a
“Commander” callsign, using [+]/[–] or the
MULTI/ CH control. To move the cursor, press
[MAIN] or [SUB]. Press [M.IN] to store the
callsign to Menu No. 62A.
3 Press [MENU], then turn the MULTI/ CH control to
access Menu No. 62B.
4 Enter your alias callsign (ex: WD6DJY-1) as a
“Transporter” callsign, using [+]/[–] or the
MULTI/ CH control. To move the cursor, press
[MAIN] or [SUB]. Press [M.IN] to store the
callsign to Menu No. 62B.
Note: You can use alpha-numeric characters, A to Z, 0 to 9 and
“–”. The callsign must be no more than 9 characters long
including “–”. Also, the following callsign formats cannot be
entered:
• WD6DJYZ
If you use only letters and numbers for the callsign, the
maximum length is 6 characters.
• WD6–DJY–1
You cannot use more than 1 “–” within a callsign.
• –WD6DJY
You cannot use a “–” as the first callsign character.
• WD6DJY–19
An SSID must be within the range of 1 to 15.
5 Access Menu No. 62C, then turn the MULTI/ CH
control to select a CTCSS tone frequency for Sky
Commander II+ (default is 88.5 Hz).
6 Access Menu No. 62D and select the
communication speed for Sky Command II+.
• Select 1200 bps or 9600 bps.
7 Access Menu No. 46 and select SUB.
8 Select a 144 MHz band frequency in FM mode on
the main transceiver and 430 (440) MHz band
frequency in FM mode for the sub-receiver for Sky
Command operation.
TS-2000 (Commander) Setup:
1 Access Menu No. 62A and 62B to enter the same
callsigns that you entered for the TS-2000
(Transporter).
2 Access Menu No. 62C to select the same CTCSS
tone frequency that you selected for the TS-2000
(Transporter).
3 Access Menu No. 62D and select the same
communication speed that you selected for the
TS-2000 (Transporter).
4 Access Menu No. 46 and select SUB.
5 Set the same frequencies that you selected for the
lortnoC noitcnuF
NIAM lortnoc
gnitarepoehtlortnocotnruT
.ycneuqerf
HC/ITLUM
lortnoc
gnitarepoehtlortnocotnruT
.yldiparycneuqerf
]NIAM[
gniviecertnerrucehtrotinomotsserP
.ycneuqerf
]BUS[
ehtllaehtezinorcnys-erotsserP
retropsnartehtneewtebnoitamrofni
.rednammocdna
]+[ / ]–[
ehtnwodropuevomotsserP
ruetamazHM05/FH(dnabgnitarepo
.)sdnaboidar
]M/OFV[
dnaedomOFVelggototsserP
.edomllaceRyromeM
]TNE[
ycneuqerfderisedaretneotsserP
yromemrodapyekciremungnisu
llaceRyromeMnirebmunlennahc
.edom
M[ ss
s
ss ]OFV
lennahcyromemehtrefsnartotsserP
.OFVotnoitamrofni
]B/A[ .BroAOFVehttcelesotsserP
]TILPS[
NOnoitarepoTILPSelggototsserP
.FFOro
]BSU/BSL[ .BSUroBSLtcelesotsserP
]KSF/WC[
ebtonnacKSF.WCtcelesotsserP
.detceles
]MA/MF[ .MAroMFtcelesotsserP
]TIR[ / ]TIX[
TIXdna/roTIRetavitcaotsserP
.noitcnuf
]RAELC[
TIRrofycneuqerftesfforaelcotsserP
.TIXdna/ro
]CORP[
rossecorPhceepSehthctiwsotsserP
.NOnoitcnuF
].N.A[
noitcnufhctoNotuAetavitcaotsserP
.FFOroNO
].C.B[
noitcnuflecnaCtaeBetavitcaotsserP
.FFOroNO
].R.N[
,1noitcudeResioNetavitcaotsserP
.FFOronoitcnuf2noitcudeResioN
]CNUF[ , ]TA[
dna1TNAneewtebelggototsserP
.dnabzHM05/FHrof2TNA
]CNUF[ , /7[
]LEVEL/BN
reknalBesioNetavitcaotsserP
.FFOroNOnoitcnuf
]CNUF[ ,
]REWOP[
.FFOrewopretropsnarTehthctiwS
“Transporter” for the main transceiver and sub-
receiver.
Starting Sky Command ll+ operation:
1 On the Transporter, access Menu No. 62E.
2 Select T-PORTER (Transporter).
3 On the Commander, access Menu No. 62E.
4 Select COMMANDER (Commander).
5 Press [MAIN] on the Commander to start the
operation.