Projector Service Manual
Table Of Contents
- DECLARATION OF CONFORMITY
- BZSAFE.PDF
- CH1INTRO.PDF
- CH2SYSDE.PDF
- Functional Descriptions
- Contents
- Cover and Base
- External Power Requirements
- Electronics Systems Overview
- System Power
- Card Cage
- Circuit Boards
- Raster Timing Generator Board (RTG) p/n 100568
- Sync Generator
- Sync Detector and Selector
- Serration and Equalization Lockout
- Phase Locked Loop
- VSYNC Detector, Field Separator, and Mux
- Adjustment Counters
- Serial Communication
- Raster Timing Generator I/O
- Interlocks and Protection
- Horizontal Deflection Board P/N 102523 (HDB)
- Vertical Oscillator
- Horizontal Phase Locked Loop
- Horizontal Centering
- Horizontal Power Supply
- Flyback Switching
- Geometric Correction
- Output Section
- Horizontal Sweep Failure Detection
- Serial Communication
- Horizontal Deflection Board I/O
- Interlocks and Protection
- Vertical Deflection Board P/N 102521(VDB)
- Vertical Preamps
- Vertical Amplifiers
- Sweep Failure Detection
- Side Pincushion and Keystone Correction
- Horizontal Linearity Correction
- Top and Bottom Pincushion and Keystone Correction
- Correction Amplifiers
- Serial Communication
- General I/O
- Interlocks and Shutdowns
- Video Processor Board P/N 104672 (VPB)
- Decoder
- Video/Sync Mux
- V & H Sync Strip
- SG Sync Strip
- B, G, and R Brightness and Contrast Amplifiers
- On-Screen Switch
- Gamma Correction
- Switch Logic and Video Enable
- RGB Sensitivity and Threshold Amplifier
- ILA® Bias
- Dynamic Focus Amplifier
- Serial Communication
- General I/O
- Interlocks and Protection
- Video Amplifier Board P/N 103567 or 103774 (VAB)
- Video Signal
- Failure Detection
- Beam Current Sense
- DC Restore
- Arc Protection
- Blanking
- Enable Circuit
- Focus
- Filament Supply
- General I/O
- System Controller Board P/N 104668 (SCB)
- General Functional Description
- CPU
- Working and Compressed Memory
- Expanded Memory
- Correction Address Generator
- DACs
- DSP
- Overlay Memory
- Overlay Address Generator
- Overlay Interface
- LED Display Buffers and Logic
- RS232 Interface
- IR Interface
- IIC Interface
- Serial Interface
- General I/O
- Backplane Board p/n 100571
- Optical Section
- Image Light Amplifier
- Functional Descriptions
- CH3ADJST.PDF
- CH4MAINT.PDF
- Maintenance Remove/Replace)
- Contents
- Introduction
- Projector Covers
- Ventilation Filters
- Arc Lamp Assembly
- System Power Supply
- Electronics Module
- Cathode Ray Tube (CRT)
- Video Amplifier Board (VAB)
- CRT Yoke
- High Voltage Power Supply (HVPS)
- Card Cage (Printed Circuit Boards)
- Image Light Amplifier Assembly
- Projection Lens
- (SCB) Socket Battery Replacement
- Recommended Spares
- Maintenance Remove/Replace)
- CH5TRBSH.PDF
- HGLOSS.PDF
Chapter 3---Service Adjustments
3-14 Model 330, 340SC, 370SC Service Manual
indicates the proper location for front and rear projection. The HJT Series 300
Projector is shipped with the jumper plug inserted in J500 for front projection. For
a rear projection setup, insert this jumper plug into J501.
J501 J500
REAR
projection
FRONT
projection
Figure 3-7
Horizontal Scan Jumper and Jacks on Horizontal Deflection Board.
The jumper is installed at the factory in J500 for front projection.
NOTE:
When replacing the horizontal deflection board, the Horizontal Deflection
Board (P/N 102523) could be damaged if the board is not seated properly on the
backplane. This problem usually occurs when the HDB is removed and reinserted
after a board failure or when changing the sweep reversal connector. A failure can
occur if connector J11 on the HDB (located at the far right when viewing from the
component side) does not connect completely with P11 on the backplane.
To ensure a proper connection between J11 and P11 follow the procedure below:
NOTE:
Before installing the Horizontal Deflection Board, remove the Vertical
Deflection Board. This allows for a full inspection of the proper connection of J11
and P11. The P11 connector on the backplane is slightly loose to allow movement
for minor dimensional differences in the position of the J11 connector on the
HDB—
Do not
tighten
connector P11 on the backplane.
To set the Horizontal Scan Jumper:
1. Turn power off at the projector and wait about five (5) minutes for the arc
lamp to cool.
2. Remove the rear cover from the projector.
3. Remove the cover from the card cage.