AV-14JT5EU / AV-21JT5EU AV-14JT5EU AV-21JT5EU COLOUR TELEVISION VICTOR COMPANY OF JAPAN, LIMITED P 2000 VICTOR COMPANY OF JAPAN, LIMITED PMJV1V2022 0500-T-CR-DW TV/AV VIDEO AUDIO INSTRUCTIONS
ADDITIONAL INFORMATIONS FOR THE SET SOLD IN GREAT BRITAIN The appliance is supplied with a moulded three pin main plug fitted with 5Amp fuse. Should the fuse require replacement, it must be replaced with a fuse rated at 5 amp and approved by ASTA or BSI to BS1362. The plug contains a removable fuse cover that must be refitted when the fuse is replaced.In the event of the fuse cover being lost or damaged, the plug must not be used until a replacement cover has been obtained.
CONTENTS IMPORTANT SAFEGUARDS ................................ 2 BEFORE LAUNCHING ......................................... 3 CONNECTING THE EXTERNAL EQUIPMENT .... 4 IDENTITY OF FEATURES ON LOCAL AND REMOTE CONTROL ............................................ 6 INSTALLATION...................................................... 8 DAILY USE ............................................................ 16 TELETEXT ............................................................ 24 TROUBLESHOOTING .........
IMPORTANT SAFEGUARDS WATER AND MOISTURE Never install the set in the following places; In a wet basement, bathroom. Do not place any container with liquid on the set. HEAT Never place the set near heat sources. VENTILATION Do not cover the ventilation opening in the cabinet and never place the set in a confined space such as bookcase or built-in unless proper ventilation is provided. Leave a minimum 10cm gap all around the unit.
BEFORE LAUNCHING INSERTING BATTERIES INTO THE CONTROL UNIT Insert the batteries (two 1.5V, type AAA(R03)) MAINS CONNECTION Plug the mains cable into the power socket with 230V/50Hz AC. AERIAL CONNECTION When using an outdoor aerial, it is usually connected to the set by means of 75 ohms. SWITCHING ON AND OFF Switching on Switch the set on with the MAIN POWER button ( ), and then PR UP or DOWN button (8P9) on the front of the set.
CONNECTING THE EXTERNAL EQUIPMENT TV and AV Use the AV button on the remote control, or on the front of the set to select one of the three options. Whenever the AV button is pressed, on the on-screen display will be changed as shown: AV S-VHS TV SCART JACK ( ): This is used to connect a VCR 1, a PERI-TV decoder 2, a Camcoder or a video game console. In most case, the set changes automatically to AV when the VCR connected is in display mode.
P TV/AV VIDEO AUDIO HEADPHONES JACK Insert the headphones plug (3,5 mm) into the headphones socket. The sound from the speaker will be cut off. VIDEO GAME OR CAMCODER FRONT AV JACK (AUDIO/VIDEO) Connect the AV (Audio/Video) socket with an appreciate cable to the corresponding socket of the external equipment. Select AV mode by pressing the AV button. Press the AV button to return to the TV mode. Note that you can play only one apparatus, if two apparatuses are connected FRONT AV JACK and SCART JACK.
IDENTITY OF FEATURES ON LOCAL AND REMOTE CONTROL LOCAL CONTROL Front P P MAIN POWER BUTTON PROGRAMME DOWN/UP BUTTONS AV STAND-BY REMOTE BUTTON INDICATOR SENSOR Back AERIAL TERMINAL ANT SCART JACK 6 VIDEO AUDIO VIDEO AUDIO TV/AV VOLUME DOWN/UP BUTTONS TV/AV VIDEO INPUT AUDIO INPUT HEAD PHONE
REMOTE CONTROL TV mode 1 10 1 POWER 2 NUMBER 0-9 3 P. MODE/OK 4 AV 5 (PR/CURSOR) UP 6 VOLUME UP (CURSOR RIGHT) 7 MENU 4 8 (PR/CURSOR) DOWN 9 9 VOLUME DOWN (CURSOR LEFT) 1 2 3 4 5 6 7 8 9 0 14 15 16 P.
INSTALLATION Read this “INSTALLATION” before using the TV for the first time. USING THE MENU 1 2 Press the MENU button to display the MENU. To exit the MENU, press the MENU button again. P Menu Picture Timer Language Install MENU Select the sub-menu title with the UP/ DOWN buttons, then press the RIGHT button to display the sub-menu. To return to the MENU, press the MENU button.
LANGUAGE SELECTION 1 2 Select LANGUAGE from the MENU with the UP/DOWN buttons, then press the RIGHT button. Menu Menu P Picture Timer Language Install P Picture Timer Language Install Select the required language with the UP/DOWN buttons. English Francais Deutsch Italiano Espanol Nederlands Svenska P P P P English Francais Deutsch Italiano Espanol Nederlands Svenska 3 Choose the appropriate country with the UP/DOWN buttons, then press the RIGHT button.
INSTALLATION 1 USING THE EDIT MENU Select INSTALL from the MENU with the UP/DOWN buttons, then press the RIGHT button. P Menu Picture Timer Language Install Menu P Picture Timer Language Install P P Install Auto setup Manual tune Fine tune Edit 3 Use the UP/DOWN buttons to select the number of the programme you want to edit.
2 Select EDIT with the UP/DOWN buttons, then press the RIGHT button. P Install P Auto setup Manual tuneu Fine tune Edit P P Edit Pr Name Ch Picture Sound Skip 01 02 03 04 05 06 07 08 C01 C07 C25 C35 C50 C63 C72 C77 Euro Euro Euro Euro Euro Euro France E/Euro --------------------------------- BG BG BG I I BG LL' DK No No No No No No No No 4 Edit the programme in accordance with the explanations of SKIP, DELETE, MOVE, NAME, CH., PICTURE and SOUND.
INSTALLATION 2 MOVE 1 The MOVE function can be used to move a channel to a different programme number. Press the MOVE button to start the MOVE function. P.MODE/OK Edit Pr Name Ch Picture Sound Skip 01 02 03 04 05 06 07 08 C01 C07 C25 C35 C50 C63 C72 C77 Euro Euro Euro Euro Euro Euro France E/Euro --------------------------------- BG BG BG I I BG LL' DK Use the UP/DOWN buttons to select the programme number to which you want to move the channel and press the MOVE button again.
PICTURE 1 2 If the picture is not displayed correctly, use the PICTURE function to change the colour system. Use the LEFT/RIGHT buttons to move the cursor to below “PICTURE”. P P Use the UP/DOWN buttons to select the colour system which displays the picture correctly.
INSTALLATION 1 2 Manually register the channel to a programme number. When no menu is displayed, use the UP/ DOWN buttons or the NUMBER 0-9 buttons to select the program number to which you want to register the channel. Display the MENU with the MENU button, then select INSTALL with the UP/ DOWN buttons and press the RIGHT button.
3 4 Select MANUAL TUNE with the UP/DOWN buttons. Press the LEFT/RIGHT buttons to search for a channel. Scanning stops when the TV finds a channel. The channel is then displayed. P P Install Auto set Manual tune Fine tune Edit Manual tune P C32 Pr01 P Note: • If the sound is not correct even when the picture of the channel is displayed correctly, press the MODE button to select the sound system that has the correct sound.
VOLUME CONTROL SELECTING A PROGRAMME NUMBER DAILY USE The set has a total of 100 programme numbers, 0...99. The NUMBER button 0...9 are used for direct programme selection. In order two digit programme, press the second numbered button within two seconds. Switch through the programme number step by step with the UP/DOWN buttons (P 8/9). Adjust the volume with the VOLUME DOWN/UP buttons (– r +) on the front of the set, or with the LEFT/RIGHT buttons on the remote control.
RECALL The RECALL button is used to display the current status: programme number, station name, clock. This display appears for 5 seconds unless any button is pressed. ? SLEEP By pressing the SLEEP button repeatedly, you can select one of the following settings: 0:00 0:20 0:40 1:00 1:20 1:40 2:00 The set will turn off after time you select. Automatic Switch-Off in No Broadcast Signal: If broadcast signal is not present for about 30 minutes, the set will be automatically turned off.
DAILY USE PICTURE ADJUSTMENT 1 2 Press the MENU button, then press the RIGHT button. P Menu MENU Picture Timer Language Install Select an item with the UP/DOWN buttons, then adjust it with the LEFT/ RIGHT buttons. P Picture Picture Brightness Contrast Colour Sharpness Brightness Contrast Colour Sharpness P USING THE MENUS WITHOUT THE REMOTE CONTROL VCR/DVD CONTROL BUTTONS P 1 P 2 You can control your JVC brand VCR or DVD player with the TV remote control.
3 Note: Your adjustments are automatically stored in the FAVOURITE mode of PICTURE MODEs. When the adjustments have been completed, press the MENU button twice and exit from the MENU. MENU OSD HALF TONE FUNCTION Contrast MENU 38 If you press the RECALL button with the MENU displayed on the screen, the OSD, except text will be half-toned. If you want to return to the normal OSD, press the RECALL button again. 2 Use the following buttons to operate the menus.
DAILY USE USING THE TIMER MENU 1 2 Select TIMER from the MENU with the UP/DOWN buttons, then press the RIGHT button. Use the UP/DOWN buttons to select the item and use the RIGHT button to move the cursor to the setting position. P Menu Menu Picture Timer Language Install Picture Timer Language Install P P P Clock Wake up Time Prog. Auto Clock Prog. P 1 --:-No --:-Pr01 No Pr01 P 2 Use the UP/DOWN buttons to set the hours, then press the RIGHT button. CLOCK Setting the TV clock.
3 4 Perform the settings in accordance with the explanations of CLOCK, WAKE UP and AUTO CLOCK. When the operation has been completed, press the MENU button twice and exit from the MENU. When you want to continue and perform some more settings, return to step 2 after using the LEFT/RIGHT buttons and move the cursor back to the left of the menu. P Clock Wake up Time Prog. Auto Clock Prog. Clock Wake up Time Prog. Auto Clock Prog.
DAILY USE 1 2 You can use the WAKE UP function to automatically turn the TV on at a set time. You can also select the channel to be displayed when the TV is turned on. Select WAKE UP from the TIMER menu with the UP/DOWN buttons, then press the RIGHT button. Clock Wake up Time Prog. Auto Clock Prog. P WAKE UP P 17:30 No --:-Pr01 No Pr01 P P 5 Select YES with the UP/DOWN buttons, then press the RIGHT button. Clock Wake up Time Prog. Auto Clock Prog.
3 4 Select TIME with the UP/DOWN buttons, then press the RIGHT button. Clock Wake up Time Prog. Auto Clock Prog. 17:30 Yes --:-Pr01 No Pr01 Clock Wake up Time Prog. Auto Clock Prog. P P Use the UP/DOWN buttons and RIGHT button to set the time at which you want the TV to be turned on. When the setting is completed, press the RIGHT button. 17:30 Yes --:-Pr01 No Pr01 Clock Wake up Time Prog. Auto Clock Prog. P P 7 17:30 Yes 07:30 Pr01 No Pr01 P P Clock Wake up Time Prog. Auto Clock Prog.
TELETEXT 1-SWITCHING TELETEXT ON/OFF Set the VCR/ /DVD switch to the (text) position, then press the TELETEXT button ( ). To return to the TV mode, press the TELETEXT button again. Note: Some of the buttons may not work if the VCR/ position. /DVD switch is not set to the (text) 2-COLOUR BUTTONS IN TOP/FLOF TELETEXT A red, green, yellow and blue field is shown at the bottom of the screen.
6-CALLING UP SUBPAGE DIRECTLY Pressing the SUBPAGE, ( ), button, “Sub-Code – – – –” appears beside page number. Enter the subpage number that you want to call up with the NUMBER button 0...9, for example, the 2nd page, sequence 0002. The desired subpage is sought and displayed. 7-WATCHING TELEVISION DURING TELETEXT MODE Some pages are continually updated, for example, stock market reports, sports announcement and the latest news. If you want to watch television and stay informed at the same ), button.
TROUBLESHOOTING • If the plug is disconnected from the AC socket, or the TV aerial has problems, you may think there is a problem with the TV itself. Be sure to check the following before calling for service. IMPORTANT • Review all instructions in this manual Problem ■ GENERAL ■ PICTURE ■ SOUND Action The TV cannot be turned on. • Insert the plug in an AC socket. • Turn the main power on. (See page 3) • The buttons on the front panel of the TV will not work if the CHILD LOCK is operating.
SPECIFICATIONS Model Item AV-14JT5EU AV-21JT5EU TV RF systems CCIR B/G, I, D/K, L Colour systems PAL, SECAM (NTSC 3.58 / 4.